Allied Telesis AR450S Betriebsanweisung Seite 94
- Seite / 119
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
94 AR400 Series Router User Guide
Software Release 2.5.2
C613-02034-00 REV A
■ the manual allocation mechanism, where a host’s IP address is assigned by
the network administrator, and DHCP is used simply to convey the
assigned address to the host.
A particular network will use one or more of these mechanisms, depending on
the policies of the network administrator.
DHCP is based on its predecessor, Bootstrap Protocol (BOOTP), but adds
automatic allocation of reusable network addresses and additional
configuration options. This software implementation supports both DHCP and
its predecessor BOOTP, but you must explicitly enable this support by a
manager command. BOOTP requests are only satisfied by policies with leases
set to INFINITY, i.e. using the automatic allocation mechanism.
Configuring DHCP
This example illustrates how to configure your router to act as a DHCP server
in a small site. The site has a limited range of IP addresses and the users only
use IP for short periods of time. The dynamic DHCP mechanism is the most
appropriate for this situation. The router on the LAN will be configured to
provide DHCP services to the PCs on the local LAN.
To configure DHCP follow these steps
The following steps are required:
1. Enable the DHCP Server.
2. Create a policy.
3. Create a range.
4. Test the configuration.
5. Configure a printer.
1. Enable the DHCP Server.
To enable DHCP, enter the command:
ENABLE DHCP
2. Create a policy.
To create a policy setting the base configuration information required by
the client hosts, enter the commands:
CREATE DHCP POLICY=base LEASE=7200
ADD DHCP POLICY=base SUBNET=255.255.255.0
ADD DHCP POLICY=base ROUTER=192.168.1.1
ADD DHCP POLICY=base DNSSERVER=192.168.1.254,
192.168.1.253
3. Create a range.
To create a range the defines the list of IP address to which the policy
applies, enter the command:
CREATE DHCP RANGE=office POLICY=base IP=192.168.1.16
NUMBER=32
- AR400 SERIES ROUTER 1
- Contents 3
- Introduction 7
- Online Technical Support 9
- Management Features 10
- Software Features 10
- Interface (CLI) 13
- Connecting a Terminal or PC 14
- Logging In 15
- Assigning an IP Address 15
- Choosing a Password 18
- Using the Commands 18
- Getting Command Line Help 19
- Interface (GUI) 23
- HTTP Proxy Servers 26
- Changing the Password 29
- Context sensitive GUI help 30
- Upgrading the GUI 30
- Time and NTP 37
- Loading Software 38
- Operating the Router 39
- Reference 42
- Storing Files in FLASH Memory 45
- Using Scripts 46
- Loading and Uploading Files 47
- Loading Files 48
- Setting LOADER Defaults 49
- Upgrading Router Software 51
- SHOW INSTALL 52
- Using the Built-in Editor 55
- SNMP and MIBs 56
- This Chapter 59
- Interfaces 60
- Naming Interfaces 61
- Ethernet Ports 62
- Asynchronous Port 62
- Virtual LANs 67
- Point to Point Protocol (PPP) 68
- Frame Relay (AR410 only) 69
- (ISDN) (AR410 only) 72
- Default Setup 73
- Testing the BRI or PRI PIC 73
- Configuring ISDN (AR410 only) 74
- Configuring Primary Rate ISDN 77
- (AR410 only) 81
- SHOW SYN=0 82
- SHOW PPP=0 82
- Configuring an IP Network 83
- Before You Start 84
- Configuring IP 84
- Configuring IP Multicasting 87
- Configuring IGMP 88
- Multicasting using DVMRP 88
- 172.74.2.3 89
- 172.74.2.2 89
- Configuring DHCP 94
- Configuring IPX 96
- Network = 401 100
- Network = 12 100
- Software Release 2.5.2 101
- C613-02034-00 REV A 101
- 172.31.108.10 105
- 172.31.1.1 105
- 172.31.2.1 105
- 172.31.2.2 105
- How the Router Starts Up 108
- How to Avoid Problems 109
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Allied Telesis AR450S
(22 Seiten)LG MC-8047ARS manuels
Manuels d'utilisation et guides de l'utilisateur pour Non LG MC-8047ARS.
Nous fournissons des manuels en pdf 1 LG MC-8047ARS à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern