Allied Telesis Rapier 16Fi-FX Installationsanleitung Seite 241
- Seite / 283
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
26 set lldp notification interval Software Reference
set lldp notification interval
Syntax SET LLDP NOTIFicationinterval=5..3600
Description This command sets the amount of time between LLDP notifications.
Notifications include SNMP traps, log messages and triggers.
The notificationinterval parameter is the number of seconds to elapse between
LLDP notifications.The notification interval prevents multiple notifications
occurring within the given time. The default is 5.
By default, all LLDP notifications are disabled. To enable them, use the enable
lldp notifications command.
Example To set the LLDP notification interval to 10 seconds, use the command:
set lldp notif=10
See Also disable lldp notifications
enable lldp notifications
set lldp reinitdelay
set lldp txdelay
set lldp txhold
set lldp txinterval
show lldp
set lldp reinitdelay
Syntax SET LLDP REINITdelay=1..10
Description This command sets the LLDP re-initialization delay.
The reinitdelay parameter specifies the number of seconds that the switch
waits after a port’s status becomes disabled before it begins the LLDP re-
initialization process. The default is 2.
Example To set the re-initialization delay to 5 seconds, use the command:
set lldp reinit=5
See Also set lldp txdelay
set lldp txhold
set lldp txinterval
show lldp
- Software Version 2.9.1 1
- 2 Release Note 2
- Release Licences 5
- Upgrading the GUI File 5
- Backwards Compatibility 6
- Overview of New Features 7
- AT-8624POE Fan Enhancements 9
- C613-10486-00 REV C 10
- VPN Configuration Wizards 11
- Command Changes 12
- System Enhancements 13
- Command Reference Updates 14
- Switching Enhancements 18
- PoE Firmware Upgrade 20
- SHDSL Enhancements 23
- Bridging Enhancements 26
- Software Version 2.9.1 27 27
- Training VLAN VID=2 28
- PPP Link 28
- Software Version 2.9.1 31 31
- Syntax SHow BRIDge 32
- Dynamic DNS Client 33
- Within a Subnet 34
- IP Debug Timeout 35
- Software Version 2.9.1 37 37
- Software Version 2.9.1 41 41
- Syntax SHow DDNS 42
- DHCP Enhancements 45
- DHCP Snooping Enhancements 50
- IP Multicasting Enhancements 55
- OSPF Enhancements 59
- BGP Enhancements 61
- IPv6 Enhancements 63
- ■ all static routes 64
- ■ all interface routes 64
- Firewall Enhancements 65
- Software Version 2.9.1 75 75
- ALG, use the command: 86
- Associations 88
- Changes to Local Commands 94
- IP Multicasting 95
- IP Multicasting 3 97
- IP Multicast Routing 98
- IP Multicasting 5 99
- PIM Dense Mode 100
- Configuring PIM Dense Mode 101
- General PIM-DM 102
- IP Multicasting 9 103
- PIM Sparse Mode 103
- 10 Software Reference 104
- Rendezvous point 105
- IP Multicasting 11 105
- 12 Software Reference 106
- Configuring PIM Sparse Mode 107
- Bootstrap router 108
- General PIM-SM 109
- IP Multicasting 17 111
- Configuring IGMP 112
- Static IGMP 113
- IGMP Proxy 114
- IGMP Snooping 116
- Downstream routers 117
- Fast Leave 118
- Query Solicitation 118
- IP Multicasting 25 119
- IGMP Filtering 120
- IGMP Throttling 122
- IP Multicasting 29 123
- Dynamic MVR 123
- Compatible MVR 123
- Immediate Leave 124
- Configuring MVR 124
- Configuration Examples 125
- Switch B 126
- Switch A 126
- Switch C 126
- Command Reference 134
- IP Multicasting enable pim 69 163
- [interface=vlan] 167
- ■ DVMRP Routers, 224.0.0.4 168
- ■ All PIM routers, 224.0.0.13 168
- ■ IGMP is enabled globally 170
- ■ the interface is active 170
- IP Multicasting set ip mvr 77 171
- 78 set pim Software Reference 172
- Syntax SHow IP IGMP DEBug 191
- Syntax SHow PIM COUnters 197
- Table 11 on page 104) 197
- Syntax SHow PIM INTerface 202
- VLAN (such as vlan1, vlan1-1) 202
- Syntax SHow PIM ROUte 205
- Syntax SHow PIM RPSet 212
- Introduction 217
- Link Layer Discovery Protocol 217
- Type Length Values 218
- Transmission and Reception 219
- Transmission 220
- Reception 220
- Storing LLDP Information 221
- Configuring LLDP 223
- Monitoring LLDP 224
- LLDP Triggers 225
- 802.1AB-2005 251
- LLDP neighbours is displayed 255
- MAC-Forced Forwarding 259
- 2 Software Reference 260
- MAC-Forced 261
- Forwarding with 261
- DHCP snooping 261
- Isolating clients using VLANs 262
- Manually adding 263
- ■ ARP packets 264
- Debugging 265
- Logging 265
- 8 Software Reference 266
- See Also show macff interface 277
- Syntax SHOW MACFF DATABase 278
Verwandte Produkte und Handbücher für Netzwerk-Switches Allied Telesis Rapier 16Fi-FX
(44 Seiten)
(51 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern