Allied Telesis AT-8824 Installationsanleitung Seite 19
- Seite / 202
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Software Version 2.7.5 19
Software Version 2.7.5
C613-10454-00 REV A
For different types of port on AT-9900 series switches, the valid speed options
are shown in the following table.
Command Changes
The following table summarises the modified command (see Command
Reference Updates)
Command Reference Updates
This section describes the modified command. The new options are shown in
bold.
set switch port
Syntax SET SWItch POrt={port-list|ALL}
[SPeed={AUTOnegotiate|10MAUTo|10MHAUto|10MHALf|
10MFAuto|10MFUll|100MAUto|100MHAUto|100MHALf|100MFAuto|
100MFUll|1000MHAUto|1000MHALf|1000MFAUto|1000MFUll}]
[other-options...]
Description On the speed parameter:
■ The new 10mauto option sets the port speed to 10Mbps. The port
autonegotiates the duplex mode.
■ The new 100mauto option sets the port speed to 100Mbps. The port
autonegotiates the duplex mode.
■ The new 1000mfull option sets the port speed to 1000Mbps and the duplex
mode to full duplex. The port uses this speed and duplex mode instead of
autonegotiating.
The speed and duplex mode options that apply depend on the router or switch
model and the type of port.
Port type Speed parameter options
RJ-45 copper ports autonegotiate
10mauto, 10mhauto, 10mhalf, 10mfauto, 10mfull
100mauto, 100mhauto, 100mhalf, 100mfauto, 100mfull
1000mfull, 1000mfauto
copper SFPs autonegotiate
10mauto, 10mhauto, 10mhalf, 10mfauto, 10mfull
100mauto, 100mhauto, 100mhalf, 100mfauto, 100mfull
1000mfull, 1000mfauto
fibre SFPs autonegotiate
1000mfull, 1000mfauto
Command Change
set switch port New 1000mfull option
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Verwandte Produkte und Handbücher für Netzwerk-Switches Allied Telesis AT-8824
(179 Seiten)
(32 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern