Allied Telesis AT-8824 Installationsanleitung Seite 174
- Seite / 202
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-52 add ip routemap Release Note
Software Version 2.7.5
C613-10454-00 REV A
EXAct Whether the community attribute in an update message must
precisely match the route map’s community list. Only valid when you
specify both match and community.
Default: no
YES An update message only matches the route map entry
if its community attribute contains all the communities
specified in the community list and only those
communities.
NO An update message still matches the route map entry if
its community attribute contains all the communities
specified in the community list plus extra communities.
INTerface A router or switch interface. A route matches the route map entry if
its next hop is out the specified interface. Valid interfaces are:
• eth (such as eth0, eth0-1)
• ATM (such as atm0.1)
• PPP (such as ppp0, ppp1-1)
• FR (such as fr0, fr0-1)
• X.25 DTE (such as x25t0, x25t0-1)
• VLAN (such as vlan1, vlan1-1)
To see a list of interfaces currently available, use the show interface
command.
Valid when filtering OSPF routes.
Default: no default
MED The update message’s Multi_Exit_Discriminator attribute. EBGP uses
the MED to determine the optimal path for reaching the advertised
prefixes. A lower metric indicates a preferred path. IBGP does not use
this attribute. An update message matches the route map entry if its
MED attribute matches this value.
Valid when filtering BGP routes.
Default: no default
METric The OSPF metric or a range of metric values. A route matches the
route map entry if its OSPF metric equals this value or is in this range.
Valid when filtering OSPF routes.
Default: no default
NEXThop The IP address of the next node in the path to the route’s destination,
specified in dotted decimal notation. For BGP, an update message
matches the route map entry if its next_hop attribute matches this
address.
Valid when filtering routes from any source.
Default: no default
ORIGin An origin attribute value, which indicates BGP’s source for the routes
at their originating AS. An update message matches the route map
entry if its origin attribute matches this value.
Valid when filtering BGP routes.
Default: no default
IGP The original source of the route was IGP.
EGP The original source of the route was EGP.
INCOmplete The original source of the route was neither IGP or EGP.
This includes statically-configured routes.
Parameter (cont.) Description (cont.)
- Software Version 2.7.5 1
- Overview of New Features 4
- MSS Clamping 5
- 8 MSS Clamping Release Note 8
- Software Version 2.7.5 9 9
- 10 MSS Clamping Release Note 10
- Syntax SHow PPP PPPoe 11
- Command changes 13
- Command Reference Updates 14
- Software Version 2.7.5 15 15
- Command Changes 18
- Syntax SHow IP 21
- DHCP Option 82 Relay 22
- Software Version 2.7.5 25 25
- Syntax SHow BOOTp RELAy 26
- IGMP Enhancements 28
- Filtering and Throttling 29
- Configuring IGMP 30
- IGMP Throttling 31
- Software Version 2.7.5 33 33
- Software Version 2.7.5 35 35
- OSPF Network Types 41
- [{FULl 45
- BGP Enhancements 46
- Automatic Summarising 48
- Aggregating Routes 50
- Software Version 2.7.5 53 53
- Syntax SHow BGP 55
- Syntax SHow BGP PEer[=ipadd] 56
- Software Version 2.7.5 59 59
- Software Version 2.7.5 61 61
- Firewall Enhancements 63
- UDP Port Timeout 65
- Software Version 2.7.5 67 67
- Software Version 2.7.5 73 73
- WAN Load Balancing 74
- VRRP Preemption Delay 75
- Software Version 2.7.5 77 77
- ..3600] [PRIOrity=1..254] 77
- Operating Principles 80
- Load Distribution Methods 81
- 1-4 Release Note 82
- WAN Load Balancing 1-5 83
- Healthcheck 84
- Assigning Weights 85
- Healthchecks 86
- Operation with Firewall 87
- 1-10 Release Note 88
- Before you 89
- Parameter Description 96
- ● eth (such as eth0, eth1) 100
- ● PPP (such as ppp0, ppp1) 100
- C613-10454-00 REV A 101
- Related Commands enable wanlb 109
- Syntax SHow WANLB 112
- Syntax SHow WANLB HEALthcheck 114
- ■ eth (such as eth0, eth1) 122
- ■ PPP (such as ppp0, ppp1) 122
- Filtering IP Routes 123
- 2-2 Release Note 124
- Introduction 125
- Types of Filters 126
- About AS Path Lists 127
- About Route Maps 127
- When to use 128
- About IP Route Filters 129
- Creating Filters 130
- Creating Route Maps for BGP 131
- How to create a route map 132
- ■ exclude the update message 133
- Example comparing 134
- AS path filter and 134
- Matching on 134
- Creating Route Maps for OSPF 138
- Creating IP Route Filters 141
- Applying Filters 142
- Applying AS path 143
- ■ prefix lists 148
- ■ AS path lists 148
- ■ route maps 148
- 2-28 Release Note 150
- [other-options] 150
- Filtering IP Routes 2-29 151
- The filtering 151
- Limitations of route 153
- Interface Routes 154
- Statically-Configured Routes 155
- Configuration Examples 156
- Using a Route Map 157
- Using an AS Path Filter 158
- Using Communities 160
- Command Reference 162
- Parameters for both 173
- Parameters for 173
- Parameters for set 176
- ■ an entire route map 181
- [PREfix=ipadd] 182
Verwandte Produkte und Handbücher für Netzwerk-Switches Allied Telesis AT-8824
(179 Seiten)
(32 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern