Allied-telesis AT-S95 CLI Bedienungsanleitung

613-001359 Rev AManagement SoftwareAT-S95◆CLIUser’s GuideFor use with the AT-8000GS Series Stackable Gigabit Ethernet SwitchesVersion 2.0.0.22

Page 10 Allied Telesis AT-S95 Management Software CLI User’s Guidesnmp-server set...

Page 100 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 8. Ethernet Configuration Commandsinterface ethernetThe interface ethernet

Ethernet Configuration CommandsPage 101Command ModeGlobal Configuration modeUser GuidelinesCommands under the interface range context are executed ind

Page 102 Allied Telesis AT-S95 Management Software CLI User’s GuidedescriptionThe description Interface Configuration (Ethernet, port-channel) mode c

Ethernet Configuration CommandsPage 103Command ModeInterface Configuration (Ethernet, port-channel) modeUser GuidelinesThe no speed command in a port-

Page 104 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example configures the duplex operation of Ethernet port 1/e5

Ethernet Configuration CommandsPage 105Parameters•on — Force flow control as enabled.• off — Force flow control as disabled.• auto — Enable AUTO flow

Page 106 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleIn the following example, automatic crossover is enabled on port 1/e5.back-

Ethernet Configuration CommandsPage 107Default ConfigurationThis command has no default configuration.Command ModeGlobal Configuration modeUser Guidel

Page 108 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•interface — Valid Ethernet port. (Full syntax: unit/port)• port-channel

Ethernet Configuration CommandsPage 109show interfaces configurationThe show interfaces configuration Privileged EXEC mode command displays the config

Page 11show ip ssh ...

Page 110 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example displays the configuration of all configured interfac

Ethernet Configuration CommandsPage 111Command ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for this command.ExampleThe followi

Page 112 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•interface — Valid Ethernet port. (Full syntax: unit/port)• port-channel

Ethernet Configuration CommandsPage 113Command ModesUser EXEC modeUser GuidelinesThere are no user guidelines for this command.Example The following e

Page 114 Allied Telesis AT-S95 Management Software CLI User’s GuideThe following table describes the fields shown in the display:ch70000ch80000consol

Ethernet Configuration CommandsPage 115port storm-control include-multicast (IC)The port storm-control include-multicast Interface Configuration (Ethe

Page 116 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxport storm-control broadcast enableno port storm-control broadcast enablePar

Ethernet Configuration CommandsPage 117User GuidelinesUse the port storm-control broadcast enable Interface Configuration mode command to enable Broad

Page 118 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 9. GVRP Commandsgvrp enable (Global)GARP VLAN Registration Protocol (GVRP)

GVRP CommandsPage 119Default ConfigurationGVRP is disabled on all interfaces.Command ModeInterface Configuration (Ethernet, port-channel) modeUser Gui

Page 12 Allied Telesis AT-S95 Management Software CLI User’s Guideshow users ...

Page 120 Allied Telesis AT-S95 Management Software CLI User’s GuideSet the same GARP timer values on all Layer 2-connected devices. If the GARP timer

GVRP CommandsPage 121no gvrp registration-forbidDefault ConfigurationDynamic registration of VLANs on the port is allowed.Command ModeInterface Config

Page 122 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxshow gvrp configuration [ethernet interface | port-channel port-channel-numb

GVRP CommandsPage 123Syntaxshow gvrp statistics [ethernet interface | port-channel port-channel-number]Parameters•interface — A valid Ethernet port. (

Page 124 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeUser EX

IGMP Snooping CommandsPage 125Chapter 10.IGMP Snooping CommandsNoteIn order to enable IGMP snooping, the user must enable bridge Multicast filteringip

Page 126 Allied Telesis AT-S95 Management Software CLI User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationIGMP snoo

IGMP Snooping CommandsPage 127ExampleThe following example enables automatic learning of Multicast device ports on VLAN 2.ip igmp snooping host-time-o

Page 128 Allied Telesis AT-S95 Management Software CLI User’s GuideParametersThis command has no arguments or keywordsDefault ConfigurationDisabled.C

IGMP Snooping CommandsPage 129User GuidelinesIf an IP address is not configured by this command, and no IP address is configured for the IGMP querier

Page 13ip http exec-timeout...

Page 130 Allied Telesis AT-S95 Management Software CLI User’s Guideused for setting the aging-out time after Multicast device ports are automatically

IGMP Snooping CommandsPage 131Command ModeInterface Configuration (VLAN) modeUser GuidelinesThe leave timeout should be set greater than the maximum t

Page 132 Allied Telesis AT-S95 Management Software CLI User’s Guideshow ip igmp snooping interfaceThe show ip igmp snooping interface EXEC mode comma

IGMP Snooping CommandsPage 133Exampleconsole# show ip igmp snooping interface 1000IGMP Snooping is globally enabledIGMP Snooping admin: EnabledHosts a

Page 134 Allied Telesis AT-S95 Management Software CLI User’s Guideshow ip igmp snooping groupsThe show ip igmp snooping groups command displays the

IP Addressing CommandsPage 135Chapter 11.IP Addressing Commandsip addressThe ip address Interface Configuration (Ethernet, VLAN, port-channel) mode co

Page 136 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•host-name — Specifies the name of the host to be placed in the DHCP opt

IP Addressing CommandsPage 137Default ConfigurationNo default gateway is defined.Command ModeGlobal Configuration modeUser Guidelines There are no use

Page 138 Allied Telesis AT-S95 Management Software CLI User’s Guidearp The arp Global Configuration mode command adds a permanent entry in the Addres

IP Addressing CommandsPage 139no arp timeoutParameters•seconds — Time (in seconds) that an entry remains in the ARP cache. (Range: 1-40000000)Default

Page 14 Allied Telesis AT-S95 Management Software CLI User’s GuidePrefaceThis guide describes how to configure an AT-S94 v1.1.0 Series switch using t

Page 140 Allied Telesis AT-S95 Management Software CLI User’s Guideshow arpThe show arp Privileged EXEC mode command displays entries in the ARP tabl

IP Addressing CommandsPage 141no ip domain-lookupParametersThis command has no arguments or keywords.Default Configuration The default configuration i

Page 142 Allied Telesis AT-S95 Management Software CLI User’s Guideclear hostThe clear host Privileged EXEC mode command deletes entries from the hos

IP Addressing CommandsPage 143Example The following example deletes all entries from the host name-to-address mapping.show hostsThe show hosts Privile

Page 144 Allied Telesis AT-S95 Management Software CLI User’s Guide---- ----- ------- ------ ---------www.stanford.edu 72 3 IP 171.64.14.203

IPv6 Addressing CommandsPage 145Chapter 12.IPv6 Addressing Commandsipv6 enableThe ipv6 enable Interface Configuration mode command enables IPv6 proces

Page 146 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•ipv6-address — The IPv6 network assigned to the interface. The address

IPv6 Addressing CommandsPage 147User GuidelinesUsing the no ipv6 address link-local command removes the manually configured link-local IPv6 address fr

Page 148 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example defines an IPv6 default gateway.show ipv6 interfaceTh

IPv6 Addressing CommandsPage 149show ipv6 routeThe show ipv6 route command displays the current state of the ipv6 routing table. Syntaxshow ipv6 route

PrefaceIntended AudiencePage 15• Chapter 25. "RMON Commands" — Display the Remote Network Monitoring (RMON) Ethernet history statistics, ala

Page 150 Allied Telesis AT-S95 Management Software CLI User’s GuideUnicast IPv6 addresses of the interface. Use the no form of this command to return

IPv6 Addressing CommandsPage 151ipv6 hostThe ipv6 host Global Configuration mode command defines a static host name-to-address mapping in the host nam

Page 152 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•ipv6_addr — Valid IPv6 address to map to the specified MAC address.• hw

IPv6 Addressing CommandsPage 153Default ConfigurationThis command has no default setting.Command ModePrivileged EXEC mode.User Guidelines•The associat

Page 154 Allied Telesis AT-S95 Management Software CLI User’s GuideParametersThis command has no keywords or arguments.Default ConfigurationThis comm

Line CommandsPage 155Chapter 13.Line CommandslineThe line Global Configuration mode command identifies a specific line for configuration and enters th

Page 156 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThe default speed is 115200 bps.Command ModeLine Configuratio

Line CommandsPage 157exec-timeoutThe exec-timeout Line Configuration mode command sets the interval that the system waits until user input is detected

Page 158 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesThis command enables the command history function for a specified l

Line CommandsPage 159ParametersThis command has no arguments or keywords.Default ConfigurationThe default configuration for all terminal sessions is d

Page 16 Allied Telesis AT-S95 Management Software CLI User’s GuideContacting Allied TelesisThis section provides Allied Telesis contact information f

Page 160 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example configures the command history buffer size to 20 comm

Line CommandsPage 161SSH configuration:Interactive timeout: 10 minutes 10 secondsHistory: 10

Page 162 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 14.DHCP Option 82 Commandsip dhcp information optionThe ip dhcp informatio

DHCP Option 82 CommandsPage 163Command ModePrivileged EXECUser GuidelinesThere are no user guidelines for this command.ExampleThe following example di

Page 164 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 15.LACP Commandslacp system-priorityThe lacp system-priority Global Config

LACP CommandsPage 165lacp port-priorityThe lacp port-priority Interface Configuration (Ethernet) mode command configures physical port priority. Use t

Page 166 Allied Telesis AT-S95 Management Software CLI User’s Guidelacp timeoutThe lacp timeout Interface Configuration (Ethernet) mode command assig

LACP CommandsPage 167show lacp ethernetThe show lacp ethernet Privileged EXEC mode command displays LACP information for Ethernet ports. Syntaxshow la

Page 168 Allied Telesis AT-S95 Management Software CLI User’s Guidedistributing: FALSEexpired: FALSEPartnersystem priority: 0system mac addr: 00:00:0

LACP CommandsPage 169show lacp port-channelThe show lacp port-channel Privileged EXEC mode command displays LACP information for a port-channel.Syntax

Using the CLICLI Command ModesPage 17Chapter 1. Using the CLIOverviewThis chapter describes how to start using the CLI and the CLI command editing fea

Page 170 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 16.LLDP Commandslldp enable (global)The lldp enable Global Configuration m

LLDP CommandsPage 171Default ConfigurationEnabled in both modes.Command Modes Interface Configuration (Ethernet) mode.User Guidelines•LLDP manages LAG

Page 172 Allied Telesis AT-S95 Management Software CLI User’s Guidelldp hold-multiplierThe lldp hold-multiplier Global Configuration mode command spe

LLDP CommandsPage 173Command ModeGlobal Configuration mode.User GuidelinesThere are no user guidelines for this command.ExampleThe following example s

Page 174 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxlldp optional-tlv tlv1 [tlv2 … tlv5]no lldp optional-tlvParameters•tlv — Spe

LLDP CommandsPage 175ExampleThe following example specifies that the management address will be advertised from an interface as 192.168.0.1.lldp med e

Page 176 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•number — Network policy sequential number.• application — The name or t

LLDP CommandsPage 177User Guidelines•For each port, only one network policy per application (voice, voice-signaling, guest-voice, guest-voice-signalin

Page 178 Allied Telesis AT-S95 Management Software CLI User’s Guideclear lldp rxThe clear lldp rx Privileged EXEC mode command restarts the LLDP RX s

LLDP CommandsPage 179ExampleThe following example displays the Link Layer Discovery Protocol (LLDP) configuration:The following table describes the si

Page 18 Allied Telesis AT-S95 Management Software CLI User’s Guide2. Enter the password and press <Enter>. The password is displayed as *. The

Page 180 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•interface — Ethernet interface.Default ConfigurationThis command has no

LLDP CommandsPage 181show lldp localThe show lldp local Privileged EXEC mode command displays the LLDP information advertised from a specific port. Sy

Page 182 Allied Telesis AT-S95 Management Software CLI User’s Guideshow lldp neighborsThe show lldp neighbors Privileged EXEC mode command displays i

LLDP CommandsPage 183ExampleThe following example displays information about neighboring devices discovered using Link Layer Discovery Protocol (LLDP)

Page 184 Allied Telesis AT-S95 Management Software CLI User’s GuideThe following table describes significant LLDP fields:DSCP: 0LLDP-MED Power over E

LLDP CommandsPage 185Auto-negotiation Advertised CapabilitiesThe speed/duplex/flow-control capabilities of the port that are advertised by the auto-ne

Page 186 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 17.Login Banner Commandslogin bannerThe login banner Privileged EXEC mode

Login Banner CommandsPage 187Command ModePrivileged EXEC mode.User GuidelinesThere are no user guidelines for this command.ExampleThe following exampl

Page 188 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 18.Management ACL Commandsmanagement access-listThe management access-list

Management ACL CommandsPage 189ExampleThe following example creates a management Access List called mlist, configures management Ethernet interfaces 1

Using the CLICLI Command ModesPage 19Interface Configuration and Specific Configuration ModesInterface Configuration mode commands modify specific int

Page 190 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesRules with Ethernet, VLAN and port-channel parameters are valid onl

Management ACL CommandsPage 191ExampleThe following example denies all ports in the Access List called mlist.management access-classThe management acc

Page 192 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for th

PHY Diagnostics CommandsPage 193Chapter 19.PHY Diagnostics Commandstest copper-port tdrThe test copper-port tdr Privileged EXEC mode command uses Time

Page 194 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeUser EX

PHY Diagnostics CommandsPage 195ExampleThe following example displays the estimated copper cable length attached to all ports.show fiber-ports optical

Page 196 Allied Telesis AT-S95 Management Software CLI User’s Guide7/e3 CopperTemp – Internally measured transceiver temperature. Voltage - Internall

Port Channel CommandsPage 197Chapter 20.Port Channel Commandsinterface port-channelThe interface port-channel Global Configuration mode command enters

Page 198 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesCommands under the interface r

Port Channel CommandsPage 199Parameters•port-channel-number — Valid port-channel number.Default ConfigurationThis command has no default configuration

Copyright © 2010, Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Page 20 Allied Telesis AT-S95 Management Software CLI User’s GuideStarting the CLIThe device can be managed over a direct connection to the device co

Page 200 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 21.Port Monitor Commandsport monitorThe port monitor Interface Configurati

Port Monitor CommandsPage 201show ports monitorThe show ports monitor User EXEC mode command displays the port monitoring status.Syntaxshow ports moni

Page 202 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 22.Power over Ethernet Commandspower inlineThe port inline Interface Confi

Power over Ethernet CommandsPage 203Default ConfigurationThis command has no default configuration.Command ModeInterface Configuration (Ethernet) mode

Page 204 Allied Telesis AT-S95 Management Software CLI User’s Guidepower inline usage-thresholdThe power inline usage-threshold Global Configuration

Power over Ethernet CommandsPage 205User GuidelinesThere are no user guidelines for this command.ExampleThe following example enables inline power tra

Page 206 Allied Telesis AT-S95 Management Software CLI User’s GuideThe following table describes the significant fields shown in the example:console#

Power over Ethernet CommandsPage 207show power inline power-consumptionThe show power inline power-consumption User EXEC mode command displays informa

Page 208 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeUser EXEC modeUser GuidelinesThere are no user guidelines for this com

QoS CommandsPage 209Chapter 23.QoS CommandsqosThe qos Global Configuration mode command enables quality of service (QoS) on the device. Use the no for

Using the CLIEditing FeaturesPage 21To enter commands that require parameters, enter the required parameters after the command keyword. For example, t

Page 210 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe following

QoS CommandsPage 211Parameters•rate — Maximum kilobits per second of ingress traffic on a port. (Range: 3500 - 1000000).Default Configuration1000 Kbit

Page 212 Allied Telesis AT-S95 Management Software CLI User’s Guideshow qos interfaceThe show qos interface User EXEC mode command displays interface

QoS CommandsPage 213wrr-queue cos-mapThe wrr-queue cos-map Global Configuration mode command maps Class of Service (CoS) values to a specific egress q

Page 214 Allied Telesis AT-S95 Management Software CLI User’s Guideqos trust (Global)The qos trust Global Configuration mode command configures the s

QoS CommandsPage 215Parameters•dscp-list — Specifies up to 8 DSCP values separated by a space. (Range: 0 - 63)• queue-id — Specifies the queue number

Page 216 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesIf the port is trusted, the default CoS value of the port is used t

QoS CommandsPage 217The following table describes the significant fields shown above.Column Descriptiond1 Decimal Bit 1 of DSCPd2 Decimal Bit 2 of DSC

Page 218 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 24.Radius Commandsradius-server hostThe radius-server host Global Configur

Radius CommandsPage 219User GuidelinesTo specify multiple hosts, multiple radius-server host commands can be used. If no host-specific timeout, retrie

Page 22 Allied Telesis AT-S95 Management Software CLI User’s Guidecommand is entered. If the characters already entered are not enough for the system

Page 220 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxradius-server retransmit retriesno radius-server retransmitParameters•retrie

Radius CommandsPage 221ExampleThe following example configures the source IP address used for communication with RADIUS servers to 10.1.1.1.radius-ser

Page 222 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThe timeout value is 3 seconds.Command ModeGlobal Configurati

Radius CommandsPage 223Syntaxshow radius-serversParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default c

Page 224 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 25.RMON Commandsshow rmon statisticsThe show rmon statistics User EXEC mod

RMON CommandsPage 225The following table describes significant fields shown above:Field Description Octets The total number of octets of data (includi

Page 226 Allied Telesis AT-S95 Management Software CLI User’s Guidermon collection historyThe rmon collection history Interface Configuration (Ethern

RMON CommandsPage 227Default ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesThere are no user guideli

Page 228 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeUser EX

RMON CommandsPage 229The following table describes significant fields shown above:console> show rmon history 1 otherSample Set: 1 Owner: MeInterfac

Using the CLIEditing FeaturesPage 23Copying and Pasting TextUp to 1000 lines of text (i.e., commands) can be copied and pasted into the device.NoteIt

Page 230 Allied Telesis AT-S95 Management Software CLI User’s Guidermon alarmThe rmon alarm Global Configuration mode command configures alarm condit

RMON CommandsPage 231Command ModeGlobal Configuration modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following example co

Page 232 Allied Telesis AT-S95 Management Software CLI User’s GuideThe following table describes significant fields shown above:show rmon alarmThe sh

RMON CommandsPage 233ExampleThe following example displays RMON 1 alarms.The following table describes the significant fields shown in the display:con

Page 234 Allied Telesis AT-S95 Management Software CLI User’s Guidermon eventThe rmon event Global Configuration mode command configures an event. Us

RMON CommandsPage 235ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command ModeUs

Page 236 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•event — Specifies the event index. (Range: 0 - 65535)Default Configurat

RMON CommandsPage 237Syntaxrmon table-size {history entries | log entries}no rmon table-size {history | log}Parameters•history entries — Maximum numbe

Page 238 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 26.SNMP Commandssnmp-server communityThe snmp-server community Global Conf

SNMP CommandsPage 239The internal security name for SNMPv1 and SNMPv2 security models is mapped to the group name.ExampleThe following example defines

Page 24 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 2. ACL Commandsip access-listThe ip access-list Global Configuration mode c

Page 240 Allied Telesis AT-S95 Management Software CLI User’s Guidesnmp-server groupThe snmp-server group Global Configuration mode command configure

SNMP CommandsPage 241snmp-server userThe snmp-server user Global Configuration mode command configures a new SNMP Version 3 user. Use the no form of t

Page 242 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example configures an SNMPv3 user John in group user-group.sn

SNMP CommandsPage 243local engine ID. The user’s command line password is then destroyed, as required by RFC 2274. As a result, the security digests o

Page 244 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxsnmp-server filter filter-name oid-tree {included | excluded}no snmp-server

SNMP CommandsPage 245Parameters•ipv4-address — IPv4 address of the host (the targeted recipient). An out-of-band IP address can be specified as descri

Page 246 Allied Telesis AT-S95 Management Software CLI User’s Guidesnmp-server v3-hostThe snmp-server v3-host Global Configuration mode command speci

SNMP CommandsPage 247ExampleThe following example configures an SNMPv3 host.snmp-server trap authenticationThe snmp-server trap authentication Global

Page 248 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesDo not include spaces in the t

SNMP CommandsPage 249Parameters•variable-name — MIB variable name.• name value — List of name and value pairs. In the case of scalar MIBs, only a sing

ACL CommandsPage 25permit-udp {any | {source source-wildcard}} {any | source-port} {any | {destination destination-wildcard}} {any | destination-port}

Page 250 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example displays the SNMP communications status.The following

SNMP CommandsPage 251show snmp engineidThe show snmp engineID Privileged EXEC mode command displays the ID of the local Simple Network Management Prot

Page 252 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for th

SNMP CommandsPage 253The following table describes significant fields shown above.show snmp filtersThe show snmp filters Privileged EXEC mode command

Page 254 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example displays the configuration of filters.show snmp users

Spanning-Tree CommandsPage 255Chapter 27.Spanning-Tree Commandsspanning-treeThe spanning-tree Global Configuration mode command enables spanning-tree

Page 256 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationSTP is enabled.Command Modes Global Configuration modeUser Gu

Spanning-Tree CommandsPage 257spanning-tree hello-timeThe spanning-tree hello-time Global Configuration mode command configures the spanning tree brid

Page 258 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesWhen configuring the maximum age, the following relationships shoul

Spanning-Tree CommandsPage 259ParametersThis command has no arguments or keywords.Default ConfigurationSpanning tree is enabled on all ports.Command M

Page 26 Allied Telesis AT-S95 Management Software CLI User’s Guide•dscp — Indicates matching the dscp number with the packet dscp value. • ip-precede

Page 260 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesThe path cost method is configured using the spanning-tree pathcost

Spanning-Tree CommandsPage 261ParametersThis command has no arguments or keywords.Default ConfigurationPortFast mode is disabled.Command Modes Interfa

Page 262 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example enables shared spanning-tree on Ethernet port 1/e16.s

Spanning-Tree CommandsPage 263Default ConfigurationThe default setting is flooding.Command Modes Global Configuration modeUser GuidelinesThere are no

Page 264 Allied Telesis AT-S95 Management Software CLI User’s Guidespanning-tree bpduguardThe spanning-tree bpduguard Interface Configuration (Ethern

Spanning-Tree CommandsPage 265User GuidelinesThis feature should be used only when working in RSTP or MSTP mode.ExampleThe following example restarts

Page 266 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•hop-count—Number of hops in an MST region before the BDPU is discarded

Spanning-Tree CommandsPage 267spanning-tree mst costThe spanning-tree mst cost Interface Configuration mode command configures the path cost for multi

Page 268 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeGlobal

Spanning-Tree CommandsPage 269ExampleThe following example maps VLANs 10 - 20 to MST instance 1.name (mst)The name MST Configuration mode command defi

ACL CommandsPage 27am-here, mobile-registration-request, mobile-registration-reply, domain-name-request, domain-name-reply, skip and photuris. (Range:

Page 270 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThe default configuration revision number is 0.Command ModeMS

Spanning-Tree CommandsPage 271exit (mst)The exit MST Configuration mode command exits the MST configuration mode and applies all configuration changes

Page 272 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeMST Configuration modeUser GuidelinesThere are no user guidelines for

Spanning-Tree CommandsPage 273ExamplesThe following examples displays spanning-tree information.console# show spanning-treeSpanning tree enabled mode

Page 274 Allied Telesis AT-S95 Management Software CLI User’s Guide---- ------- -------- ----- --- ---- -------- ----------1/e1 Enabled 128.1 20000 F

Spanning-Tree CommandsPage 275console# show spanning-tree activeSpanning tree enabled mode RSTPDefault port cost method: longRoot ID Priority 32768Add

Page 276 Allied Telesis AT-S95 Management Software CLI User’s GuideName State Prio.Nbr Cost Sts Role PortFast Type---- ------- -------- ----- --- ---

Spanning-Tree CommandsPage 277Number of transitions to forwarding state: 1BPDU: sent 2, received 170638Port 3 (1/e3) disabledState: N/A Role: N/APort

Page 278 Allied Telesis AT-S95 Management Software CLI User’s Guideconsole# show spanning-tree ethernet 1/e1Port 1 (1/e1) enabledState: Forwarding Ro

Spanning-Tree CommandsPage 279Name State Prio.Nbr Cost Sts Role PortFast Type---- ------- -------- ----- --- ---- -------- ----------1/e1 Enabled 128.

Page 28 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•disable-port — The Ethernet interface is disabled if the condition is ma

Page 280 Allied Telesis AT-S95 Management Software CLI User’s GuideHello Time 2 sec Max Age 20 sec Forward Delay 15 secIST Master ID Priority 32768Ad

Spanning-Tree CommandsPage 281Port 4 (1/e4) enabledState: Forwarding Role: DesignatedPort id: 128.4 Port cost: 20000 Type: Shared (configured: auto)

Page 282 Allied Telesis AT-S95 Management Software CLI User’s GuideDesignated port id: 128.2 Designated cost: 20000Guard Root: Disabled BPDU Guard: D

Spanning-Tree CommandsPage 283Address 00:02:4b:19:7a:00Path Cost 10000Rem hops 19Bridge ID Priority 32768Address 00:02:4b:29:7a:00Hello Time 2 sec Max

Page 284 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 28.SSH Commandsip ssh portThe ip ssh port Global Configuration mode comman

SSH CommandsPage 285Command ModeGlobal Configuration modeUser GuidelinesIf encryption keys are not generated, the SSH server is in standby until the k

Page 286 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxcrypto key generate rsaParametersThis command has no arguments or keywords.D

SSH CommandsPage 287ExampleThe following example enables public key authentication for incoming SSH sessions.crypto key pubkey-chain sshThe crypto key

Page 288 Allied Telesis AT-S95 Management Software CLI User’s Guideuser-keyThe user-key SSH Public Key-string Configuration mode command specifies wh

SSH CommandsPage 289Default ConfigurationNo keys exist.Command ModeSSH Public Key-string Configuration modeUser GuidelinesUse the key-string SSH Publi

ACL CommandsPage 29Default ConfigurationNo IPv4 Access List is defined.Command ModeIP Access-list Configuration modeUser Guidelines•Enter IP-Access Li

Page 290 Allied Telesis AT-S95 Management Software CLI User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationThis comm

SSH CommandsPage 291Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser GuidelinesThere are no user gu

Page 292 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example displays SSH public keys stored on the device.console

Syslog CommandsPage 293Chapter 29.Syslog Commandslogging onThe logging on Global Configuration mode command controls error message logging. This comma

Page 294 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•ipv4-address — Specifies the IPv4 address of the host to be used as a s

Syslog CommandsPage 295Command ModeGlobal Configuration modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following example

Page 296 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxlogging buffered size numberno logging buffered sizeParameters•number — Spec

Syslog CommandsPage 297logging fileThe logging file Global Configuration mode command limits syslog messages sent to the logging file based on severit

Page 298 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example clears messages from the logging file.aaa loggingThe

Syslog CommandsPage 299Parameters•copy — Indicates logging messages related to file copy operations.• delete-rename — Indicates logging messages relat

Page 3Table of ContentsPreface ...

Page 30 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationNo IPv6 access list is defined.Command ModeGlobal configuratio

Page 300 Allied Telesis AT-S95 Management Software CLI User’s Guideshow loggingThe show logging Privileged EXEC mode command displays the state of lo

Syslog CommandsPage 301show logging fileThe show logging file Privileged EXEC mode command displays the state of logging and the syslog messages store

Page 302 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example displays the logging state and the syslog messages st

Syslog CommandsPage 303ExampleThe following example displays the settings of the syslog servers.console# show syslog-serversDevice ConfigurationIP add

Page 304 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 30.TACACS+ Commandstacacs-server hostThe tacacs-server host Global Configu

TACACS+ CommandsPage 305ExampleThe following example specifies a TACACS+ host.tacacs-server keyThe tacacs-server key Global Configuration mode command

Page 306 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault Configuration5 secondsCommand ModeGlobal Configuration modeUser Guidelines

TACACS+ CommandsPage 307Syntaxshow tacacs [ip-address]Parameters•ip-address — Name or IP address of the TACACS+ server.Default ConfigurationThis comma

Page 308 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 31.Tunnel Commandsinterface tunnelThe interface tunnel Global Configuratio

Tunnel CommandsPage 309Command ModeInterface Tunnel Configuration mode.User Guidelines•The system can be enabled to an ISATAP tunnel. When enabled, an

ACL CommandsPage 31Parameters•destination-port — Specifies the UDP/TCP destination port. (Range: 0- 65535)• destination-prefix/length — The destinatio

Page 310 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example configures a global string ATI_Tunnel_Router to repre

Tunnel CommandsPage 311no tunnel isatap query-intervalParameters•seconds — Specifies the number of seconds between DNS Queries. (Range: 10 - 3600)Defa

Page 312 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example configures the interval between ISATAP router solicit

Tunnel CommandsPage 313Default ConfigurationThis command has no default setting.Command ModePrivileged EXEC mode.User GuidelinesThere are no user guid

Page 314 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 32.System Management CommandspingThe ping User EXEC mode command sends ICM

System Management CommandsPage 315– physical-port-name = Product specific.• When using the ping ipv6 command to check network connectivity of a direct

Page 316 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•ip-address — IP address of the destination host. An out-of-band IP addr

System Management CommandsPage 317Several concurrent Telnet sessions can be opened and switched. To open a subsequent session, the current connection

Page 318 Allied Telesis AT-S95 Management Software CLI User’s GuidereloadThe reload Privileged EXEC mode command reloads the operating system.Syntaxr

System Management CommandsPage 319resumeSyntaxresume [connection]Default ConfigurationThe default connection number is that of the most recent connect

Page 32 Allied Telesis AT-S95 Management Software CLI User’s GuideUser Guidelines•IPv6 Syntax — The 128-bit IPv6 address format is divided into eight

Page 320 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example specifies the device host name.stack masterThe stack

System Management CommandsPage 321stack reloadNoteThis command is operational in the AT-S94/24, AT-S94/24POE, AT-S94/48 and AT-S94/48POE devices.The s

Page 322 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThe automatically configured unit number is assigned.Command

System Management CommandsPage 323show usersThe show users User EXEC mode command displays information about the active users.Syntaxshow users---- ---

Page 324 Allied Telesis AT-S95 Management Software CLI User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationThis comm

System Management CommandsPage 325Example The following example lists open Telnet sessions.The following table describes significant fields shown abov

Page 326 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example displays the system information.show system idThe sho

System Management CommandsPage 327Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser GuidelinesThere

Page 328 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example displays system version information (only for demonst

User Interface CommandsPage 329Chapter 33.User Interface CommandsdoThe do command executes an EXEC-level command from Global Configuration mode or any

ACL CommandsPage 33Parameters•destination-port — Specifies the UDP/TCP destination port. (Range: 0 - 65535)• destination-prefix/length — The destinati

Page 330 Allied Telesis AT-S95 Management Software CLI User’s GuideenableThe enable User EXEC mode command enters the Privileged EXEC mode.Syntaxenab

User Interface CommandsPage 331ExampleThe following example returns to Users EXEC mode.loginThe login User EXEC mode command changes a login username.

Page 332 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for th

User Interface CommandsPage 333ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Comm

Page 334 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxhelpParametersThis command has no arguments or keywords.Default Configuratio

User Interface CommandsPage 335Command ModeUser EXEC modeUser GuidelinesBy default, a More prompt is displayed when the output contains more lines tha

Page 336 Allied Telesis AT-S95 Management Software CLI User’s Guideshow privilegeThe show privilege Privileged/User EXEC mode command displays the cu

VLAN CommandsPage 337Chapter 34.VLAN Commandsvlan databaseThe vlan database Global Configuration mode command enters the VLAN Configuration mode.Synta

Page 338 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeVLAN Configuration modeUser GuidelinesThere are no user guidelines for

VLAN CommandsPage 339Syntaxinterface range vlan {vlan-range | all}Parameters•vlan-range — Specifies a list of VLAN IDs to be added. Separate nonconsec

Page 34 Allied Telesis AT-S95 Management Software CLI User’s GuideUser Guidelines•IPv6 Syntax — The 128-bit IPv6 address format is divided into eight

Page 340 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example gives VLAN number 19 the name Marketing.switchport pr

VLAN CommandsPage 341switchport modeThe switchport mode Interface Configuration mode command configures the VLAN membership mode of a port. Use the no

Page 342 Allied Telesis AT-S95 Management Software CLI User’s Guideswitchport access vlanThe switchport access vlan Interface Configuration mode comm

VLAN CommandsPage 343User GuidelinesThere are no user guidelines for this command.ExampleThe following example adds VLANs 1, 2, 5 to 6 to the allowed

Page 344 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•add vlan-list — Specifies the list of VLAN IDs to be added. Separate no

VLAN CommandsPage 345ExampleThe following example configures the PVID for Ethernet port 1/e16, when the interface is in general mode.switchport genera

Page 346 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeInterface Configuration (Ethernet, port-channel) modeUser GuidelinesTh

VLAN CommandsPage 347ExampleThe following example sets a mac-based classification rule.map mac macs-groupThe map mac macs-group VLAN Configuration mod

Page 348 Allied Telesis AT-S95 Management Software CLI User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationThis comm

VLAN CommandsPage 349ExampleThe following example forbids adding VLAN IDs 234 to 256 to Ethernet port 1/e16.ip internal-usage-vlanThe ip internal-usag

ACL CommandsPage 35ExampleThe following example creates a MAC ACL.permit (MAC)The permit MAC-Access List Configuration mode command sets permit condit

Page 350 Allied Telesis AT-S95 Management Software CLI User’s Guideshow vlanThe show vlan Privileged EXEC mode command displays VLAN information.Synt

VLAN CommandsPage 351ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command ModePr

Page 352 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example displays the switchport configuration for Ethernet po

VLAN CommandsPage 35373 outconsole# show interface switchport ethernet 1/e2Port 1/e2:VLAN Membership mode: GeneralOperating parameters:PVID: 4095 (dis

Page 354 Allied Telesis AT-S95 Management Software CLI User’s GuideAcceptable Frame Type: UntaggedGVRP status: Disabled

Web Server CommandsPage 355Chapter 35.Web Server Commandsip http serverThe ip http server Global Configuration mode command enables configuring the de

Page 356 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesUse the crypto certificate gen

Web Server CommandsPage 357Syntaxip https serverno ip https serverParametersThis command has no arguments or keywords.Default ConfigurationDisabled.Co

Page 358 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example configures the https port number to 100.ip https exec

Web Server CommandsPage 359Parameters•number — Specifies the certificate number. (Range: 1 - 2)• key-generate — Regenerate the SSL RSA key.• length —

Page 36 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•disable-port — Indicates the Ethernet interface is disabled if the condi

Page 360 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxcrypto certificate number request [cn common- name ] [ou organization-unit]

Web Server CommandsPage 361ExampleThe following example generates and displays a certificate request for HTTPS.crypto certificate importThe crypto cer

Page 362 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example imports a certificate signed by Certification Authori

Web Server CommandsPage 363show crypto certificate mycertificateThe show crypto certificate mycertificate Privileged EXEC mode command displays the SS

Page 364 Allied Telesis AT-S95 Management Software CLI User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationThis comm

Web Server CommandsPage 365Certificate 1 is activeIssued by: www.verisign.comValid from: 8/9/2008 to 8/9/2009Subject: CN= router.gm.com, 0= General Mo

Page 366 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 36. 802.1x Commandsaaa authentication dot1x The aaa authentication dot1x G

802.1x CommandsPage 367no dot1x system-auth-controlParametersThis command has no arguments or keywords.Default Configuration802.1x is disabled globall

Page 368 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesIt is recommended to disable spanning tree or to enable spanning-tr

802.1x CommandsPage 369Parameters•seconds — Number of seconds between re-authentication attempts. (Range: 300 - 4294967295)Default ConfigurationRe-aut

ACL CommandsPage 37Parameters•input — Applies the specified ACL to the input interface.Default ConfigurationThis command has no default configuration.

Page 370 Allied Telesis AT-S95 Management Software CLI User’s Guidedot1x timeout quiet-periodThe dot1x timeout quiet-period Interface Configuration m

802.1x CommandsPage 371Default ConfigurationTimeout period is 30 seconds.Command Mode Interface Configuration (Ethernet) modeUser GuidelinesThe defaul

Page 372 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example sets the number of times that the device sends an EAP

802.1x CommandsPage 373Parameters•seconds — Time in seconds that the device waits for a response from the authentication server. (Range: 1 - 65535 sec

Page 374 Allied Telesis AT-S95 Management Software CLI User’s Guide802.1x is disabledPort Admin Mode Oper Mode Reauth ControlReauth PeriodUsername---

802.1x CommandsPage 375The following table describes significant fields shown above:show dot1x usersThe show dot1x users Privileged EXEC mode command

Page 376 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxshow dot1x users [username username]Parameters•username — Supplicant usernam

802.1x CommandsPage 377show dot1x statisticsThe show dot1x statistics Privileged EXEC mode command displays 802.1X statistics for the specified interf

Page 378 Allied Telesis AT-S95 Management Software CLI User’s GuideThe following table describes the significant fields shown in the display:dot1x au

802.1x CommandsPage 379Command Mode Interface Configuration (VLAN) modeUser GuidelinesAn access port cannot be a member in an unauthenticated VLAN.The

Page 38 Allied Telesis AT-S95 Management Software CLI User’s Guideshow interfaces access-listsThe show interfaces access-lists Privileged EXEC mode c

Page 380 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example defines VLAN 2 as a guest VLAN.dot1x single-host-viol

802.1x CommandsPage 381ExampleThe following example forwards frames with source addresses that are not the supplicant address and sends consecutive tr

Page 382 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxshow dot1x advanced interfaceParameters•interface — Ethernet interface.Defau

802.1x CommandsPage 383dot1x guest-vlan enableThe dot1x guest-vlan enable Interface Configuration mode command enables unauthorized users on the inter

Page 384 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•sec — Specify the timeout in seconds. (Range: 30 – 180)Default Configur

802.1x CommandsPage 385User GuidelinesThe command is relevant when multiple hosts is disabled and the user has been successfully authenticated.Example

Page 386 Allied Telesis AT-S95 Management Software CLI User’s Guidedot1x legacy-supp-modeUse the dot1x legacy-supp-mode interface configuration comma

IndexPage 387IndexAaaa accounting dot1x 47aaa accounting login 46aaa authentication dot1x 366aaa authentication dot1x default 366aaa authentication en

Page 388 Allied Telesis AT-S95 Management Software CLI User’s Guideenable authentication 42end 333Entering Commands 20exec-timeout 157exit 332exit (C

IndexPage 389logging 293logging buffered 295logging buffered size 295logging console 294logging file 297logging on 293login 331login authentication 41

AAA CommandsPage 39Chapter 3. AAA Commandsaaa authentication loginThe aaa authentication login Global Configuration mode command defines login authent

Page 390 Allied Telesis AT-S95 Management Software CLI User’s Guideshow fiber-ports optical-transceiver 195show gvrp configuration 121show gvrp error

IndexPage 391snmp-server v3-host 246snmp-server view 239sntp anycast client enable 77sntp authenticate 75sntp authentication-key 74sntp broadcast clie

Page 392 Allied Telesis AT-S95 Management Software CLI User’s Guide

Page 4 Allied Telesis AT-S95 Management Software CLI User’s Guidelogin authentication...

Page 40 Allied Telesis AT-S95 Management Software CLI User’s GuideUser Guidelines•The default and optional list names created with the aaa authentica

AAA CommandsPage 41Command ModeGlobal Configuration modeUser Guidelines•The default and optional list names created with the aaa authentication enable

Page 42 Allied Telesis AT-S95 Management Software CLI User’s Guideenable authenticationThe enable authentication Line Configuration mode command spec

AAA CommandsPage 43Default ConfigurationThe local user database is checked. This has the same effect as the command ip http authentication local.Comma

Page 44 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesThe additional methods of authentication are used only if the previo

AAA CommandsPage 45passwordThe password Line Configuration mode command specifies a password on a line. Use the no form of this command to remove the

Page 46 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxusername name [password password] [level level] [encrypted]no username namePa

AAA CommandsPage 47Command ModeGlobal Configuration mode.User Guidelines•This command enables the recording of device management sessions (Telnet, ser

Page 48 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•radius — Accounting is performed by a RADIUS server.Default Configuratio

AAA CommandsPage 49show users accountsThe show users accounts Privileged EXEC mode command displays information about the local user database.Syntaxsh

Page 5sntp client enable (Interface)...78

Page 50 Allied Telesis AT-S95 Management Software CLI User’s Guideno enable password [level level]Parameters•password — Password for this level. (Ran

AAA CommandsPage 51ExampleConsole# show accountingLogin: Radius802.1x: Disabled

Page 52 Allied Telesis AT-S95 Management Software CLI User’s GuideChapter 4. Address Table Commandsbridge addressThe bridge address Interface Configu

Address Table CommandsPage 53Syntaxbridge multicast filteringno bridge multicast filteringParametersThis command has no keywords or arguments.Default

Page 54 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeInterface configuration (VLAN) modeUser Guidelines•If the command is ex

Address Table CommandsPage 55User GuidelinesBefore defining forbidden ports, the Multicast group should be registered.ExampleThe following example con

Page 56 Allied Telesis AT-S95 Management Software CLI User’s Guideno bridge multicast forward-allParameters•add — Force forwarding all Multicast pack

Address Table CommandsPage 57Command ModeInterface Configuration (VLAN) modeUser Guidelines•IGMP snooping dynamically discovers Multicast router ports

Page 58 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxclear bridgeParametersThis command has no arguments or keywords.Default Confi

Address Table CommandsPage 59ExampleThe following example forwards all packets from port 1/e1 without learning addresses of packets from unknown sourc

Page 6 Allied Telesis AT-S95 Management Software CLI User’s Guideshow interfaces description ...

Page 60 Allied Telesis AT-S95 Management Software CLI User’s GuideParameters•max-addr— Maximum number of addresses that can be learned by the port. (

Address Table CommandsPage 61ExampleThe following example adds the MAC-layer address 66:66:66:66:66:66 to port 1/e1.show bridge address-tableThe show

Page 62 Allied Telesis AT-S95 Management Software CLI User’s Guideshow bridge address-table staticThe show bridge address-table static Privileged EXE

Address Table CommandsPage 63Parameters•vlan — Specifies a valid VLAN, such as VLAN 1.• interface — A valid Ethernet port.• port-channel-number — A va

Page 64 Allied Telesis AT-S95 Management Software CLI User’s Guideshow bridge multicast address-tableThe show bridge multicast address-table Privileg

Address Table CommandsPage 65ExamplesThe following examples display Multicast MAC address and IP Address Table information.console# show bridge multic

Page 66 Allied Telesis AT-S95 Management Software CLI User’s GuideNoteA Multicast MAC address maps to multiple IP addresses as shown above.show bridg

Address Table CommandsPage 67Syntaxshow bridge multicast filtering vlan-idParameters•vlan-id — VLAN ID value.Default ConfigurationThis command has no

Page 68 Allied Telesis AT-S95 Management Software CLI User’s Guideshow bridge multicast unregisteredUse The show bridge multicast unregistered User E

Address Table CommandsPage 69Command ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following example

Page 7Chapter 12.IPv6 Addressing Commands... 145ipv6 enable...

Page 70 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault Configuration This command has no default configuration.Command ModePrivile

Clock CommandsPage 71Chapter 5. Clock Commandsclock setThe clock set Privileged EXEC mode command manually sets the system clock. To avoid an SNTP con

Page 72 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationNo external clock sourceCommand ModeGlobal Configuration modeU

Clock CommandsPage 73clock summer-timeThe clock summer-time Global Configuration mode command configures the system to automatically switch to summer

Page 74 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesIn both the date and recurring forms of the command, the first part

Clock CommandsPage 75ExampleThe following example defines the authentication key for SNTP.sntp authenticateThe sntp authenticate Global Configuration

Page 76 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationNo keys are trusted.Command ModeGlobal Configuration modeUser

Clock CommandsPage 77sntp broadcast client enableThe sntp broadcast client enable Global Configuration mode command enables Simple Network Time Protoc

Page 78 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesThe sntp client poll timer Global Configuration mode command determi

Clock CommandsPage 79Syntaxsntp unicast client enableno sntp unicast client enableParametersThis command has no arguments or keywords.Default Configur

Page 8 Allied Telesis AT-S95 Management Software CLI User’s Guidelldp med location...

Page 80 Allied Telesis AT-S95 Management Software CLI User’s GuideExampleThe following example enables polling for Simple Network Time Protocol (SNTP

Clock CommandsPage 81ExampleThe following example configures the device to accept SNTP traffic from the server on 192.1.1.1.show clockThe show clock U

Page 82 Allied Telesis AT-S95 Management Software CLI User’s Guideshow sntp configurationThe show sntp configuration Privileged EXEC mode command sho

Clock CommandsPage 83show sntp statusThe show sntp status Privileged EXEC mode command shows the status of the Simple Network Time Protocol (SNTP).Syn

Page 84 Allied Telesis AT-S95 Management Software CLI User’s Guide176.1.8.179 Unknown 12:17.17.987 PDT Feb 19 2009 8.98 189.19Anycast server:Server I

Configuration and Image File CommandsPage 85Chapter 6. Configuration and Image File CommandscopyThe copy Privileged EXEC mode command copies files fro

Page 86 Allied Telesis AT-S95 Management Software CLI User’s GuideDefault ConfigurationThis command has no default configuration.Command ModePrivileg

Configuration and Image File CommandsPage 87Copying a Configuration File from a Server to the Startup ConfigurationTo copy a configuration file from a

Page 88 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe following e

Configuration and Image File CommandsPage 89Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser Guidel

Page 9show qos ...

Page 90 Allied Telesis AT-S95 Management Software CLI User’s GuideSyntaxshow running-configParametersThis command has no arguments or keywords.Defaul

Configuration and Image File CommandsPage 91Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser Guidel

Page 92 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe following e

DHCP Snooping CommandsPage 93Chapter 7. DHCP Snooping Commandsip dhcp snoopingThe ip dhcp snooping Global Configuration mode command globally enables

Page 94 Allied Telesis AT-S95 Management Software CLI User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesDHCP snooping must be first glo

DHCP Snooping CommandsPage 95ip dhcp snooping information option allowed-untrustedThe ip dhcp snooping information option allowed-untrusted Global Con

Page 96 Allied Telesis AT-S95 Management Software CLI User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe following e

DHCP Snooping CommandsPage 97Parameters•seconds — Specify, in seconds, the update frequency (Range: 600 - 86400).Default Configuration1200Command Mode

Page 98 Allied Telesis AT-S95 Management Software CLI User’s GuideThe entry is displayed in the show commands as a ‘DHCP Snooping entry’.ExampleThe f

DHCP Snooping CommandsPage 99User GuidelinesThere are no user guidelines for this command.Example The following example displays the DHCP snooping con