Allied-telesis AT-S95 CLI (AT-8000GS Series) Bedienungsanleitung Seite 1

613-001982 Rev. AManagementSoftwareAT-S95CLI User’s GuideAT-8000GS Series Stackable Gigabit Ethernet SwitchesVersion 2.0.0.27

Page 10 Allied Telesis AT-8000GS Command Line Interface User’s Guidesnmp-server filter...

Page 100 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesThere are no user guidelines for this command.Example The followi

DHCP Snooping CommandsPage 101Exampleconsole# show ip dhcp snooping bindingTotal number of binding: 2MAC Adreess IP Address Lease (sec) T

Page 102 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 8. Ethernet Configuration Commandsinterface ethernetThe interface ethern

Ethernet Configuration CommandsPage 103Command ModeGlobal Configuration modeUser GuidelinesCommands under the interface range context are executed ind

Page 104 Allied Telesis AT-8000GS Command Line Interface User’s GuidedescriptionThe description Interface Configuration (Ethernet, port-channel) mode

Ethernet Configuration CommandsPage 105Command ModeInterface Configuration (Ethernet, port-channel) modeUser GuidelinesThe no speed command in a port-

Page 106 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example configures the duplex operation of Ethernet port 1/

Ethernet Configuration CommandsPage 107Parameters•on — Force flow control as enabled.• off — Force flow control as disabled.• auto — Enable AUTO flow

Page 108 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleIn the following example, automatic crossover is enabled on port 1/g5.bac

Ethernet Configuration CommandsPage 109Command ModeGlobal Configuration mode.User GuidelinesThe command is effective only after reset.ExampleThe follo

Page 11crypto key generate dsa...289

Page 110 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•ethernet — Valid Ethernet port. (Full syntax: unit/port)• port-channe

Ethernet Configuration CommandsPage 111show interfaces advertiseThe show interfaces advertise Privileged EXEC mode command displays autonegotiation da

Page 112 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow interfaces configurationThe show interfaces configuration Privileged EXEC m

Ethernet Configuration CommandsPage 113show interfaces statusThe show interfaces status Privileged EXEC mode command displays the status of all config

Page 114 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow interfaces descriptionThe show interfaces description Privileged EXEC mode

Ethernet Configuration CommandsPage 115ExampleThe following example displays descriptions of configured interfaces.show ports jumbo-frameThe show port

Page 116 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow interfaces countersThe show interfaces counters User EXEC mode command disp

Ethernet Configuration CommandsPage 117The following table describes the fields shown in the display:show system flowcontrolThe show system flowcontro

Page 118 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesThere are no user guidelines for this command.Exampleport storm-c

Ethernet Configuration CommandsPage 119ParametersThis command has no arguments or keywords.Default ConfigurationBroadcast storm control is disabled.Co

Page 12 Allied Telesis AT-8000GS Command Line Interface User’s Guideresume...

Page 120 Allied Telesis AT-8000GS Command Line Interface User’s GuideExample The following example configures the maximum storm control Broadcast rat

GVRP CommandsPage 121Chapter 9. GVRP Commandsgvrp enable (Global)GARP VLAN Registration Protocol (GVRP) is an industry-standard protocol designed to p

Page 122 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationGVRP is disabled on all interfaces.Command ModeInterface Co

GVRP CommandsPage 123Set the same GARP timer values on all Layer 2-connected devices. If the GARP timers are set differently on Layer 2-connected devi

Page 124 Allied Telesis AT-8000GS Command Line Interface User’s Guideno gvrp registration-forbidDefault ConfigurationDynamic registration of VLANs on

GVRP CommandsPage 125Syntaxshow gvrp configuration [ethernet interface | port-channel port-channel-number]Parameters•interface — A valid Ethernet port

Page 126 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxshow gvrp statistics [ethernet interface | port-channel port-channel-numbe

GVRP CommandsPage 127Default ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesThere are no user guideli

Page 128 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 10.IGMP Snooping CommandsNoteIn order to enable IGMP snooping, the user

IGMP Snooping CommandsPage 129ParametersThis command has no arguments or keywords.Default ConfigurationIGMP snooping is disabled .Command ModeInterfac

Page 13show vlan ...

Page 130 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example enables automatic learning of Multicast device port

IGMP Snooping CommandsPage 131ParametersThis command has no arguments or keywordsDefault ConfigurationDisabled.Command ModeInterface Configuration (VL

Page 132 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesIf an IP address is not configured by this command, and no IP add

IGMP Snooping CommandsPage 133used for setting the aging-out time after Multicast device ports are automatically learned. Use the no form of this comm

Page 134 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModeInterface Configuration (VLAN) modeUser GuidelinesThe leave timeout

IGMP Snooping CommandsPage 135show ip igmp snooping interfaceThe show ip igmp snooping interface EXEC mode command shows IGMP snooping configuration.S

Page 136 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleconsole# show ip igmp snooping interface 1000IGMP Snooping is globally en

IGMP Snooping CommandsPage 137show ip igmp snooping groupsThe show ip igmp snooping groups command displays the Multicast groups that was learned by t

Page 138 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 11.IP Addressing Commandsip addressThe ip address Interface Configuratio

IP Addressing CommandsPage 139Parameters•host-name — Specifies the name of the host to be placed in the DHCP option 12 field. This name does not have

Page 14 Allied Telesis AT-8000GS Command Line Interface User’s GuidePrefaceThis guide describes how to configure an AT-S95 v1.0.0 Series switch using

Page 140 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationNo default gateway is defined.Command ModeGlobal Configurat

IP Addressing CommandsPage 141arp The arp Global Configuration mode command adds a permanent entry in the Address Resolution Protocol (ARP) cache. Use

Page 142 Allied Telesis AT-8000GS Command Line Interface User’s Guideno arp timeoutParameters•seconds — Time (in seconds) that an entry remains in th

IP Addressing CommandsPage 143show arpThe show arp Privileged EXEC mode command displays entries in the ARP table.Syntaxshow arp [ip-address ip-addres

Page 144 Allied Telesis AT-8000GS Command Line Interface User’s Guideno ip domain-lookupParametersThis command has no arguments or keywords.Default C

IP Addressing CommandsPage 145ExampleThe following example defines default domain name www.website.com.ip name-serverThe ip name-server Global Configu

Page 146 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault Configuration No host is defined.Command Mode Interface Configuration (V

IP Addressing CommandsPage 147Parameters•name — Specifies the host entry to be removed. (Range: 1 - 158 characters)• * — Removes all entries.Default C

Page 148 Allied Telesis AT-8000GS Command Line Interface User’s GuideName/address lookup is enabled Name servers (Preference order): 176.16.1.18 176.

IPv6 Addressing CommandsPage 149Chapter 12.IPv6 Addressing Commandsipv6 enableThe ipv6 enable Interface Configuration mode command enables IPv6 proces

PrefaceIntended AudiencePage 15• Chapter 25. "RMON Commands" — Display the Remote Network Monitoring (RMON) Ethernet history statistics, ala

Page 150 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•ipv6-address — The IPv6 network assigned to the interface. The addres

IPv6 Addressing CommandsPage 151User GuidelinesUsing the no ipv6 address link-local command removes the manually configured link-local IPv6 address fr

Page 152 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example defines an IPv6 default gateway.show ipv6 interface

IPv6 Addressing CommandsPage 153show ipv6 routeThe show ipv6 route command displays the current state of the ipv6 routing table. Syntaxshow ipv6 route

Page 154 Allied Telesis AT-8000GS Command Line Interface User’s GuideUnicast IPv6 addresses of the interface. Use the no form of this command to retu

IPv6 Addressing CommandsPage 155ipv6 hostThe ipv6 host Global Configuration mode command defines a static host name-to-address mapping in the host nam

Page 156 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•ipv6_addr — Valid IPv6 address to map to the specified MAC address.•

IPv6 Addressing CommandsPage 157Default ConfigurationThis command has no default setting.Command ModePrivileged EXEC mode.User Guidelines•The associat

Page 158 Allied Telesis AT-8000GS Command Line Interface User’s GuideParametersThis command has no keywords or arguments.Default ConfigurationThis co

Line CommandsPage 159Chapter 13.Line CommandslineThe line Global Configuration mode command identifies a specific line for configuration and enters th

Page 16 Allied Telesis AT-8000GS Command Line Interface User’s GuideContacting Allied TelesisThis section provides Allied Telesis contact information

Page 160 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationThe default speed is 115200 bps.Command ModeLine Configurat

Line CommandsPage 161exec-timeoutThe exec-timeout Line Configuration mode command sets the interval that the system waits until user input is detected

Page 162 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesThis command enables the command history function for a specified

Line CommandsPage 163ParametersThis command has no arguments or keywords.Default ConfigurationThe default configuration for all terminal sessions is d

Page 164 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example configures the command history buffer size to 20 co

Line CommandsPage 165SSH configuration:Interactive timeout: 10 minutes 10 secondsHistory: 10

Page 166 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 14.DHCP Option 82 Commandsip dhcp information optionThe ip dhcp informat

DHCP Option 82 CommandsPage 167Command ModePrivileged EXECUser GuidelinesThere are no user guidelines for this command.ExampleThe following example di

Page 168 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 15.LACP Commandslacp system-priorityThe lacp system-priority Global Conf

LACP CommandsPage 169lacp port-priorityThe lacp port-priority Interface Configuration (Ethernet) mode command configures physical port priority. Use t

Using the CLICLI Command ModesPage 17Chapter 1. Using the CLIOverviewThis chapter describes how to start using the CLI and the CLI command editing fea

Page 170 Allied Telesis AT-8000GS Command Line Interface User’s Guidelacp timeoutThe lacp timeout Interface Configuration (Ethernet) mode command ass

LACP CommandsPage 171show lacp ethernetThe show lacp ethernet Privileged EXEC mode command displays LACP information for Ethernet ports. Syntaxshow la

Page 172 Allied Telesis AT-8000GS Command Line Interface User’s Guidedistributing: FALSEexpired: FALSEPartnersystem priority: 0system mac addr: 00:00

LACP CommandsPage 173show lacp port-channelThe show lacp port-channel Privileged EXEC mode command displays LACP information for a port-channel.Syntax

Page 174 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 16.LLDP Commandslldp enable (global)The lldp enable Global Configuration

LLDP CommandsPage 175Default ConfigurationEnabled in both modes.Command Modes Interface Configuration (Ethernet) mode.User Guidelines•LLDP manages LAG

Page 176 Allied Telesis AT-8000GS Command Line Interface User’s Guidelldp hold-multiplierThe lldp hold-multiplier Global Configuration mode command s

LLDP CommandsPage 177Command ModeGlobal Configuration mode.User GuidelinesThere are no user guidelines for this command.ExampleThe following example p

Page 178 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxlldp optional-tlv tlv1 [tlv2 … tlv5]no lldp optional-tlvParameters•tlv — S

LLDP CommandsPage 179ExampleThe following example specifies that the management address will be advertised from an interface as 192.168.0.1.lldp med e

Page 18 Allied Telesis AT-8000GS Command Line Interface User’s Guide2. Enter the password and press <Enter>. The password is displayed as *. Th

Page 180 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•number — Network policy sequential number.• application — The name or

LLDP CommandsPage 181User Guidelines•For each port, only one network policy per application ( voice, voice-signaling, guest-voice, guest-voice-signali

Page 182 Allied Telesis AT-8000GS Command Line Interface User’s Guideclear lldp rxThe clear lldp rx Privileged EXEC mode command restarts the LLDP RX

LLDP CommandsPage 183ExampleThe following example displays the Link Layer Discovery Protocol (LLDP) configuration:The following table describes the si

Page 184 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•interface — Ethernet interface.Default ConfigurationThis command has

LLDP CommandsPage 185show lldp localThe show lldp local Privileged EXEC mode command displays the LLDP information advertised from a specific port. Sy

Page 186 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow lldp neighborsThe show lldp neighbors Privileged EXEC mode command displays

LLDP CommandsPage 187ExampleThe following example displays information about neighboring devices discovered using Link Layer Discovery Protocol (LLDP)

Page 188 Allied Telesis AT-8000GS Command Line Interface User’s GuideThe following table describes significant LLDP fields:DSCP: 0LLDP-MED Power over

LLDP CommandsPage 189Auto-negotiation Advertised CapabilitiesThe speed/duplex/flow-control capabilities of the port that are advertised by the auto-ne

Using the CLICLI Command ModesPage 19Interface Configuration and Specific Configuration ModesInterface Configuration mode commands modify specific int

Page 190 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 17.Login Banner Commandslogin bannerThe login banner Privileged EXEC mod

Login Banner CommandsPage 191Command ModePrivileged EXEC mode.User GuidelinesThere are no user guidelines for this command.ExampleThe following exampl

Page 192 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 18.Management ACL Commandsmanagement access-listThe management access-li

Management ACL CommandsPage 193ExampleThe following example creates a management Access List called mlist, configures management Ethernet interfaces 1

Page 194 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesRules with Ethernet, VLAN and port-channel parameters are valid o

Management ACL CommandsPage 195ExampleThe following example denies all ports in the Access List called mlist.management access-classThe management acc

Page 196 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for

PHY Diagnostics CommandsPage 197Chapter 19.PHY Diagnostics Commandstest copper-port tdrThe test copper-port tdr Privileged EXEC mode command uses Time

Page 198 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeUser

PHY Diagnostics CommandsPage 199ExampleThe following example displays the estimated copper cable length attached to all ports.show fiber-ports optical

Copyright © 2014 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Page 20 Allied Telesis AT-8000GS Command Line Interface User’s GuideStarting the CLIThe device can be managed over a direct connection to the device

Page 200 Allied Telesis AT-8000GS Command Line Interface User’s Guide7/g3 CopperTemp – Internally measured transceiver temperature. Voltage - Interna

Port Channel CommandsPage 201Chapter 20.Port Channel Commandsinterface port-channelThe interface port-channel Global Configuration mode command enters

Page 202 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesCommands under the interface

Port Channel CommandsPage 203Parameters•port-channel-number — Valid port-channel number.Default ConfigurationThis command has no default configuration

Page 204 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 21.Port Monitor Commandsport monitorThe port monitor Interface Configura

Port Monitor CommandsPage 205show ports monitorThe show ports monitor User EXEC mode command displays the port monitoring status.Syntaxshow ports moni

Page 206 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 22.Power over Ethernet Commandspower inlineThe port inline Interface Con

Power over Ethernet CommandsPage 207Default ConfigurationThis command has no default configuration.Command ModeInterface Configuration (Ethernet) mode

Page 208 Allied Telesis AT-8000GS Command Line Interface User’s Guidepower inline usage-thresholdThe power inline usage-threshold Global Configuratio

Power over Ethernet CommandsPage 209User GuidelinesThere are no user guidelines for this command.ExampleThe following example enables inline power tra

Using the CLIEditing FeaturesPage 21To enter commands that require parameters, enter the required parameters after the command keyword. For example, t

Page 210 Allied Telesis AT-8000GS Command Line Interface User’s GuideThe following table describes the significant fields shown in the example:consol

Power over Ethernet CommandsPage 211show power inline power-consumptionThe show power inline power-consumption User EXEC mode command displays informa

Page 212 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModeUser EXEC modeUser GuidelinesThere are no user guidelines for this c

QoS CommandsPage 213Chapter 23.QoS CommandsqosThe qos Global Configuration mode command enables quality of service (QoS) on the device. Use the no for

Page 214 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe followin

QoS CommandsPage 215Parameters•rate — Maximum kilobits per second of ingress traffic on a port. (Range: 3500 - 1000000).Default Configuration1000 Kbit

Page 216 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow qos interfaceThe show qos interface User EXEC mode command displays interfa

QoS CommandsPage 217wrr-queue cos-mapThe wrr-queue cos-map Global Configuration mode command maps Class of Service (CoS) values to a specific egress q

Page 218 Allied Telesis AT-8000GS Command Line Interface User’s Guideqos trust (Global)The qos trust Global Configuration mode command configures the

QoS CommandsPage 219Parameters•dscp-list — Specifies up to 8 DSCP values separated by a space. (Range: 0 - 63)• queue-id — Specifies the queue number

Page 22 Allied Telesis AT-8000GS Command Line Interface User’s Guidecommand is entered. If the characters already entered are not enough for the syst

Page 220 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesIf the port is trusted, the default CoS value of the port is used

QoS CommandsPage 221The following table describes the significant fields shown above.Column Descriptiond1 Decimal Bit 1 of DSCPd2 Decimal Bit 2 of DSC

Page 222 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 24.Radius Commandsradius-server hostThe radius-server host Global Config

Radius CommandsPage 223User GuidelinesTo specify multiple hosts, multiple radius-server host commands can be used. If no host-specific timeout, retrie

Page 224 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxradius-server retransmit retriesno radius-server retransmitParameters•retr

Radius CommandsPage 225ExampleThe following example configures the source IP address used for communication with RADIUS servers to 10.1.1.1.radius-ser

Page 226 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationThe timeout value is 3 seconds.Command ModeGlobal Configura

Radius CommandsPage 227Syntaxshow radius-serversParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default c

Page 228 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 25.RMON Commandsshow rmon statisticsThe show rmon statistics User EXEC m

RMON CommandsPage 229The following table describes significant fields shown above:Field Description Octets The total number of octets of data (includi

Using the CLIEditing FeaturesPage 23Copying and Pasting TextUp to 1000 lines of text (i.e., commands) can be copied and pasted into the device.NoteIt

Page 230 Allied Telesis AT-8000GS Command Line Interface User’s Guidermon collection historyThe rmon collection history Interface Configuration (Ethe

RMON CommandsPage 231Default ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesThere are no user guideli

Page 232 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeUser

RMON CommandsPage 233The following table describes significant fields shown above:console> show rmon history 1 otherSample Set: 1 Owner: MeInterfac

Page 234 Allied Telesis AT-8000GS Command Line Interface User’s Guidermon alarmThe rmon alarm Global Configuration mode command configures alarm cond

RMON CommandsPage 235Command ModeGlobal Configuration modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following example co

Page 236 Allied Telesis AT-8000GS Command Line Interface User’s GuideThe following table describes significant fields shown above:show rmon alarmThe

RMON CommandsPage 237ExampleThe following example displays RMON 1 alarms.The following table describes the significant fields shown in the display:con

Page 238 Allied Telesis AT-8000GS Command Line Interface User’s Guidermon eventThe rmon event Global Configuration mode command configures an event.

RMON CommandsPage 239ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command ModeUs

Page 24 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 2. ACL Commandsip access-listThe ip access-list Global Configuration mode

Page 240 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•event — Specifies the event index. (Range: 0 - 65535)Default Configur

RMON CommandsPage 241Syntaxrmon table-size {history entries | log entries}no rmon table-size {history | log}Parameters•history entries — Maximum numbe

Page 242 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 26.SNMP Commandssnmp-server communityThe snmp-server community Global Co

SNMP CommandsPage 243The internal security name for SNMPv1 and SNMPv2 security models is mapped to the group name.ExampleThe following example defines

Page 244 Allied Telesis AT-8000GS Command Line Interface User’s Guidesnmp-server groupThe snmp-server group Global Configuration mode command configu

SNMP CommandsPage 245snmp-server userThe snmp-server user Global Configuration mode command configures a new SNMP Version 3 user. Use the no form of t

Page 246 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example configures an SNMPv3 user John in group user-group.

SNMP CommandsPage 247local engine ID. The user’s command line password is then destroyed, as required by RFC 2274. As a result, the security digests o

Page 248 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxsnmp-server filter filter-name oid-tree {included | excluded}no snmp-serve

SNMP CommandsPage 249Parameters•ipv4-address — IPv4 address of the host (the targeted recipient). An out-of-band IP address can be specified as descri

ACL CommandsPage 25permit-udp {any | { source source-wildcard}} {any | source-port} {any | {destination destination-wildcard}} {any | destination-port

Page 250 Allied Telesis AT-8000GS Command Line Interface User’s Guidesnmp-server v3-hostThe snmp-server v3-host Global Configuration mode command spe

SNMP CommandsPage 251ExampleThe following example configures an SNMPv3 host.snmp-server trap authenticationThe snmp-server trap authentication Global

Page 252 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModeGlobal Configuration modeUser GuidelinesDo not include spaces in the

SNMP CommandsPage 253Parameters•variable-name — MIB variable name.• name value — List of name and value pairs. In the case of scalar MIBs, only a sing

Page 254 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example displays the SNMP communications status.The followi

SNMP CommandsPage 255show snmp engineidThe show snmp engineID Privileged EXEC mode command displays the ID of the local Simple Network Management Prot

Page 256 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for

SNMP CommandsPage 257The following table describes significant fields shown above.show snmp filtersThe show snmp filters Privileged EXEC mode command

Page 258 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example displays the configuration of filters.show snmp use

Spanning-Tree CommandsPage 259Chapter 27.Spanning-Tree Commandsspanning-treeThe spanning-tree Global Configuration mode command enables spanning-tree

Page 26 Allied Telesis AT-8000GS Command Line Interface User’s Guide•dscp — Indicates matching the dscp number with the packet dscp value. • ip-prece

Page 260 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationSTP is enabled.Command Modes Global Configuration modeUser

Spanning-Tree CommandsPage 261spanning-tree hello-timeThe spanning-tree hello-time Global Configuration mode command configures the spanning tree brid

Page 262 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesWhen configuring the maximum age, the following relationships sho

Spanning-Tree CommandsPage 263ParametersThis command has no arguments or keywords.Default ConfigurationSpanning tree is enabled on all ports.Command M

Page 264 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesThe path cost method is configured using the spanning-tree pathco

Spanning-Tree CommandsPage 265ParametersThis command has no arguments or keywords.Default ConfigurationPortFast mode is disabled.Command Modes Interfa

Page 266 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example enables shared spanning-tree on Ethernet port 1/g16

Spanning-Tree CommandsPage 267Default ConfigurationThe default setting is flooding.Command Modes Global Configuration modeUser GuidelinesThere are no

Page 268 Allied Telesis AT-8000GS Command Line Interface User’s Guidespanning-tree bpduguardThe spanning-tree bpduguard Interface Configuration (Ethe

Spanning-Tree CommandsPage 269User GuidelinesThis feature should be used only when working in RSTP or MSTP mode.ExampleThe following example restarts

ACL CommandsPage 27am-here, mobile-registration-request, mobile-registration-reply, domain-name-request, domain-name-reply, skip and photuris. (Range:

Page 270 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•hop-count—Number of hops in an MST region before the BDPU is discarde

Spanning-Tree CommandsPage 271spanning-tree mst costThe spanning-tree mst cost Interface Configuration mode command configures the path cost for multi

Page 272 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command ModeGloba

Spanning-Tree CommandsPage 273ExampleThe following example maps VLANs 10 - 20 to MST instance 1.name (mst)The name MST Configuration mode command defi

Page 274 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationThe default configuration revision number is 0.Command Mode

Spanning-Tree CommandsPage 275exit (mst)The exit MST Configuration mode command exits the MST configuration mode and applies all configuration changes

Page 276 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModeMST Configuration modeUser GuidelinesThere are no user guidelines fo

Spanning-Tree CommandsPage 277ExamplesThe following examples displays spanning-tree information.console# show spanning-treeSpanning tree enabled mode

Page 278 Allied Telesis AT-8000GS Command Line Interface User’s Guide---- ------- -------- ----- --- ---- -------- ----------1/g1 Enabled 128.1 20000

Spanning-Tree CommandsPage 279console# show spanning-tree activeSpanning tree enabled mode RSTPDefault port cost method: longRoot ID Priority 32768Add

Page 28 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•disable-port — The Ethernet interface is disabled if the condition is

Page 280 Allied Telesis AT-8000GS Command Line Interface User’s GuideName State Prio.Nbr Cost Sts Role PortFast Type---- ------- -------- ----- --- -

Spanning-Tree CommandsPage 281Number of transitions to forwarding state: 1BPDU: sent 2, received 170638Port 3 (1/g3) disabledState: N/A Role: N/APort

Page 282 Allied Telesis AT-8000GS Command Line Interface User’s Guideconsole# show spanning-tree ethernet 1/g1Port 1 (1/g1) enabledState: Forwarding

Spanning-Tree CommandsPage 283Name State Prio.Nbr Cost Sts Role PortFast Type---- ------- -------- ----- --- ---- -------- ----------1/g1 Enabled 128.

Page 284 Allied Telesis AT-8000GS Command Line Interface User’s GuideHello Time 2 sec Max Age 20 sec Forward Delay 15 secIST Master ID Priority 32768

Spanning-Tree CommandsPage 285Port 4 (1/g4) enabledState: Forwarding Role: DesignatedPort id: 128.4 Port cost: 20000 Type: Shared (configured: auto)

Page 286 Allied Telesis AT-8000GS Command Line Interface User’s GuideDesignated port id: 128.2 Designated cost: 20000Guard Root: Disabled BPDU Guard:

Spanning-Tree CommandsPage 287Address 00:02:4b:19:7a:00Path Cost 10000Rem hops 19Bridge ID Priority 32768Address 00:02:4b:29:7a:00Hello Time 2 sec Max

Page 288 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 28.SSH Commandsip ssh portThe ip ssh port Global Configuration mode comm

SSH CommandsPage 289Command ModeGlobal Configuration modeUser GuidelinesIf encryption keys are not generated, the SSH server is in standby until the k

ACL CommandsPage 29Default ConfigurationNo IPv4 Access List is defined.Command ModeIP Access-list Configuration modeUser Guidelines•Enter IP-Access Li

Page 290 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxcrypto key generate rsaParametersThis command has no arguments or keywords

SSH CommandsPage 291ExampleThe following example enables public key authentication for incoming SSH sessions.crypto key pubkey-chain sshThe crypto key

Page 292 Allied Telesis AT-8000GS Command Line Interface User’s Guideuser-keyThe user-key SSH Public Key-string Configuration mode command specifies

SSH CommandsPage 293Default ConfigurationNo keys exist.Command ModeSSH Public Key-string Configuration modeUser GuidelinesUse the key-string SSH Publi

Page 294 Allied Telesis AT-8000GS Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationThis co

SSH CommandsPage 295Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser GuidelinesThere are no user gu

Page 296 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example displays SSH public keys stored on the device.conso

Syslog CommandsPage 297Chapter 29.Syslog Commandslogging onThe logging on Global Configuration mode command controls error message logging. This comma

Page 298 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•ipv4-address — Specifies the IPv4 address of the host to be used as a

Syslog CommandsPage 299Command ModeGlobal Configuration modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following example

Page 3Table of ContentsPreface...

Page 30 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationNo IPv6 access list is defined.Command ModeGlobal configurat

Page 300 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxlogging buffered size numberno logging buffered sizeParameters•number — Sp

Syslog CommandsPage 301logging fileThe logging file Global Configuration mode command limits syslog messages sent to the logging file based on severit

Page 302 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example clears messages from the logging file.aaa loggingTh

Syslog CommandsPage 303Parameters•copy — Indicates logging messages related to file copy operations.• delete-rename — Indicates logging messages relat

Page 304 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow loggingThe show logging Privileged EXEC mode command displays the state of

Syslog CommandsPage 305show logging fileThe show logging file Privileged EXEC mode command displays the state of logging and the syslog messages store

Page 306 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example displays the logging state and the syslog messages

Syslog CommandsPage 307Syntaxshow syslog-serversParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default c

Page 308 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 30.TACACS+ Commandstacacs-server hostThe tacacs-server host Global Confi

TACACS+ CommandsPage 309ExampleThe following example specifies a TACACS+ host.tacacs-server keyThe tacacs-server key Global Configuration mode command

ACL CommandsPage 31Parameters•destination-port — Specifies the UDP/TCP destination port. (Range: 0- 65535)• destination-prefix/length — The destinatio

Page 310 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault Configuration5 secondsCommand ModeGlobal Configuration modeUser Guidelin

TACACS+ CommandsPage 311Syntaxshow tacacs [ip-address]Parameters•ip-address — Name or IP address of the TACACS+ server.Default ConfigurationThis comma

Page 312 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 31.Tunnel Commandsinterface tunnelThe interface tunnel Global Configurat

Tunnel CommandsPage 313Command ModeInterface Tunnel Configuration mode.User Guidelines•The system can be enabled to an ISATAP tunnel. When enabled, an

Page 314 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example configures a global string ATI_Tunnel_Router to rep

Tunnel CommandsPage 315no tunnel isatap query-intervalParameters•seconds — Specifies the number of seconds between DNS Queries. (Range: 10 - 3600)Defa

Page 316 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example configures the interval between ISATAP router solic

Tunnel CommandsPage 317Default ConfigurationThis command has no default setting.Command ModePrivileged EXEC mode.User GuidelinesThere are no user guid

Page 318 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 32.System Management CommandspingThe ping User EXEC mode command sends I

System Management CommandsPage 319– physical-port-name = Product specific.• When using the ping ipv6 command to check network connectivity of a direct

Page 32 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser Guidelines•IPv6 Syntax — The 128-bit IPv6 address format is divided into eig

Page 320 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•ip-address — IP address of the destination host. An out-of-band IP ad

System Management CommandsPage 321Several concurrent Telnet sessions can be opened and switched. To open a subsequent session, the current connection

Page 322 Allied Telesis AT-8000GS Command Line Interface User’s GuidereloadThe reload Privileged EXEC mode command reloads the operating system.Synta

System Management CommandsPage 323resumeSyntaxresume [connection]Default ConfigurationThe default connection number is that of the most recent connect

Page 324 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example specifies the device host name.stack masterThe stac

System Management CommandsPage 325Syntaxstack reload [unit unit]Parameters•unit — Number of the unit to be reloaded (Range: 1 - 6)Default Configuratio

Page 326 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThis example changes Unit Number 6 to Unit Number 5. The command takes ef

System Management CommandsPage 327show usersThe show users User EXEC mode command displays information about the active users.Syntaxshow usersParamete

Page 328 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow sessionsThe show sessions User EXEC mode command lists open Telnet sessions

System Management CommandsPage 329Parameters•unit— Specifies the number of the unit. (Range: 1 - 6)Default ConfigurationThis command has no default co

ACL CommandsPage 33Parameters•destination-port — Specifies the UDP/TCP destination port. (Range: 0 - 65535)• destination-prefix/length — The destinati

Page 330 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example displays the system information.show system idThe s

System Management CommandsPage 331Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser GuidelinesThere

Page 332 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow system defaultsThe show system defaults User EXEC mode command displays spe

System Management CommandsPage 333ExampleThe following example displays the system defaults.console# show system defaultsSystem Mode: Switch# Manageme

Page 334 Allied Telesis AT-8000GS Command Line Interface User’s Guide20 GE regular4 GE comboDuplex: FullNegotiation: EnabledFlow control: OffMdix mod

System Management CommandsPage 335GVRP: DisabledPort mode: AccessVLAN membership: 1PVE: not defined# Network security defaultsDHCP snooping: Disabled#

Page 336 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 33.User Interface CommandsdoThe do command executes an EXEC-level comman

User Interface CommandsPage 337enableThe enable User EXEC mode command enters the Privileged EXEC mode.Syntaxenable [privilege-level]Parameters•privil

Page 338 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example returns to Users EXEC mode.loginThe login User EXEC

User Interface CommandsPage 339Command ModePrivileged EXEC modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following examp

Page 34 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser Guidelines•IPv6 Syntax — The 128-bit IPv6 address format is divided into eig

Page 340 Allied Telesis AT-8000GS Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationThis co

User Interface CommandsPage 341SyntaxhelpParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configur

Page 342 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModeUser EXEC modeUser GuidelinesBy default, a More prompt is displayed

User Interface CommandsPage 343show privilegeThe show privilege Privileged/User EXEC mode command displays the current privilege level.Syntaxshow priv

Page 344 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 34.VLAN Commandsvlan databaseThe vlan database Global Configuration mode

VLAN CommandsPage 345Command ModeVLAN Configuration modeUser GuidelinesThere are no user guidelines for this command.ExampleThe following example VLAN

Page 346 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxinterface range vlan {vlan-range | all}Parameters•vlan-range — Specifies a

VLAN CommandsPage 347ExampleThe following example gives VLAN number 19 the name Marketing.switchport protectedThe switchport protected Interface Confi

Page 348 Allied Telesis AT-8000GS Command Line Interface User’s Guideswitchport modeThe switchport mode Interface Configuration mode command configur

VLAN CommandsPage 349switchport access vlanThe switchport access vlan Interface Configuration mode command configures the VLAN ID when the interface i

ACL CommandsPage 35ExampleThe following example creates a MAC ACL.permit (MAC)The permit MAC-Access List Configuration mode command sets permit condit

Page 350 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesThere are no user guidelines for this command.ExampleThe followin

VLAN CommandsPage 351Parameters•add vlan-list — Specifies the list of VLAN IDs to be added. Separate nonconsecutive VLAN IDs with a comma and no space

Page 352 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example configures the PVID for Ethernet port 1/g16, when t

VLAN CommandsPage 353Command ModeInterface Configuration (Ethernet, port-channel) modeUser GuidelinesThere are no user guidelines for this command.Exa

Page 354 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example sets a mac-based classification rule.map mac macs-g

VLAN CommandsPage 355ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command ModePr

Page 356 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example forbids adding VLAN IDs 234 to 256 to Ethernet port

VLAN CommandsPage 357show vlanThe show vlan Privileged EXEC mode command displays VLAN information.Syntaxshow vlan [tag vlan-id | name vlan-name ]Para

Page 358 Allied Telesis AT-8000GS Command Line Interface User’s GuideParametersThis command has no arguments or keywords.Default ConfigurationThis co

VLAN CommandsPage 359ExampleThe following example displays the switchport configuration for Ethernet port 1/g1.console# show interface switchport ethe

Page 36 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•disable-port — Indicates the Ethernet interface is disabled if the con

Page 360 Allied Telesis AT-8000GS Command Line Interface User’s Guide73 outconsole# show interface switchport ethernet 1/g2Port 1/g2:VLAN Membership

VLAN CommandsPage 361Acceptable Frame Type: UntaggedGVRP status: Disabled

Page 362 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 35.Web Server Commandsip http serverThe ip http server Global Configurat

Web Server CommandsPage 363Command ModeGlobal Configuration modeUser GuidelinesUse the crypto certificate generate Global Configuration mode command t

Page 364 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxip https serverno ip https serverParametersThis command has no arguments o

Web Server CommandsPage 365ExampleThe following example configures the https port number to 100.ip https exec-timeoutiThe ip https exec-timeout Global

Page 366 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•number — Specifies the certificate number. (Range: 1 - 2)• key-genera

Web Server CommandsPage 367Syntaxcrypto certificate number request [cn common- name ] [ou organization-unit] [or organization] [loc location] [st stat

Page 368 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example generates and displays a certificate request for HT

Web Server CommandsPage 369ExampleThe following example imports a certificate signed by Certification Authority for HTTPS.ip https certificateThe ip h

ACL CommandsPage 37Parameters•input — Applies the specified ACL to the input interface.Default ConfigurationThis command has no default configuration.

Page 370 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow crypto certificate mycertificateThe show crypto certificate mycertificate P

Web Server CommandsPage 371ParametersThis command has no arguments or keywords.Default ConfigurationThis command has no default configuration.Command

Page 372 Allied Telesis AT-8000GS Command Line Interface User’s GuideCertificate 1 is activeIssued by: www.verisign.comValid from: 8/9/2008 to 8/9/20

802.1x CommandsPage 373Chapter 36. 802.1x Commandsaaa authentication dot1x The aaa authentication dot1x Global Configuration mode command specifies on

Page 374 Allied Telesis AT-8000GS Command Line Interface User’s Guideno dot1x system-auth-controlParametersThis command has no arguments or keywords.

802.1x CommandsPage 375User GuidelinesIt is recommended to disable spanning tree or to enable spanning-tree PortFast mode on 802.1x edge ports (ports

Page 376 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•seconds — Number of seconds between re-authentication attempts. (Rang

802.1x CommandsPage 377dot1x timeout quiet-periodThe dot1x timeout quiet-period Interface Configuration mode command sets the number of seconds that t

Page 378 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationTimeout period is 30 seconds.Command Mode Interface Configu

802.1x CommandsPage 379ExampleThe following example sets the number of times that the device sends an EAP-request/identity frame to 6 .dot1x timeout s

Page 38 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow interfaces access-listsThe show interfaces access-lists Privileged EXEC mode

Page 380 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•seconds — Time in seconds that the device waits for a response from t

802.1x CommandsPage 381802.1x is enabledPort Admin Mode Oper Mode Reauth ControlReauth PeriodUsername---- ---------- --------- ------- ------ --------

Page 382 Allied Telesis AT-8000GS Command Line Interface User’s GuideThe following table describes significant fields shown above:show dot1x usersThe

802.1x CommandsPage 383Syntaxshow dot1x users [username username]Parameters•username — Supplicant username (Range: 1 - 160 characters)Default Configur

Page 384 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow dot1x statisticsThe show dot1x statistics Privileged EXEC mode command disp

802.1x CommandsPage 385The following table describes the significant fields shown in the display:dot1x auth-not-reqThe dot1x auth-not-req Interface Co

Page 386 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand Mode Interface Configuration (VLAN) modeUser GuidelinesAn access port ca

802.1x CommandsPage 387ExampleThe following example defines VLAN 2 as a guest VLAN.dot1x mac-authenticationThe mac-authentication Interface Configurat

Page 388 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow dot1x advancedThe show dot1x advanced privileged EXEC mode command displays

802.1x CommandsPage 389dot1x guest-vlan enableThe dot1x guest-vlan enable Interface Configuration mode command enables unauthorized users on the inter

AAA CommandsPage 39Chapter 3. AAA Commandsaaa authentication loginThe aaa authentication login Global Configuration mode command defines login authent

Page 390 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxdot1x guest-vlan timeout secno dot1x guest-vlan timeoutParameters•sec — Sp

802.1x CommandsPage 391Command ModeInterface Configuration (Ethernet) modeUser GuidelinesThe command is relevant when multiple hosts is disabled and t

Page 392 Allied Telesis AT-8000GS Command Line Interface User’s GuideExamplesThe following example enables user-based VLAN assignment.console(config)

IndexPage 393IndexAaaa accounting dot1x 47aaa accounting login 46aaa authentication dot1x 373aaa authentication dot1x default 373aaa authentication en

Page 394 Allied Telesis AT-8000GS Command Line Interface User’s Guideexit (Configuration) 339exit (mst) 275Ffile-system logging 302flowcontrol 106Gga

IndexPage 395logging on 297login 338login authentication 41login banner 190Mmanagement access-class 195management access-list 192management logging 30

Page 396 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow interfaces advertise 111show interfaces counters 116show interfaces descrip

IndexPage 397sntp client enable (Interface) 79sntp client poll timer 77sntp server 81sntp trusted-key 76sntp unicast client enable 79sntp unicast clie

Page 4 Allied Telesis AT-8000GS Command Line Interface User’s Guidelogin authentication...

Page 40 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser Guidelines•The default and optional list names created with the aaa authenti

AAA CommandsPage 41Command ModeGlobal Configuration modeUser Guidelines•The default and optional list names created with the aaa authentication enable

Page 42 Allied Telesis AT-8000GS Command Line Interface User’s Guideenable authenticationThe enable authentication Line Configuration mode command sp

AAA CommandsPage 43Default ConfigurationThe local user database is checked. This has the same effect as the command ip http authentication local.Comma

Page 44 Allied Telesis AT-8000GS Command Line Interface User’s GuideUser GuidelinesThe additional methods of authentication are used only if the prev

AAA CommandsPage 45passwordThe password Line Configuration mode command specifies a password on a line. Use the no form of this command to remove the

Page 46 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxusername name [password password] [level level] [encrypted]no username name

AAA CommandsPage 47Command ModeGlobal Configuration mode.User Guidelines•This command enables the recording of device management sessions (Telnet, ser

Page 48 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•radius — Accounting is performed by a RADIUS server.Default Configurat

AAA CommandsPage 49show users accountsThe show users accounts Privileged EXEC mode command displays information about the local user database.Syntaxsh

Page 5sntp anycast client enable...78

Page 50 Allied Telesis AT-8000GS Command Line Interface User’s Guideenable password The enable password Global Configuration mode command sets a loca

AAA CommandsPage 51User GuidelinesThere are no user guidelines for this command.ExampleConsole# show accountingLogin: Radius802.1x: Disabled

Page 52 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 4. Address Table Commandsbridge addressThe bridge address Interface Confi

Address Table CommandsPage 53Syntaxbridge multicast filteringno bridge multicast filteringParametersThis command has no keywords or arguments.Default

Page 54 Allied Telesis AT-8000GS Command Line Interface User’s GuideCommand ModeInterface configuration (VLAN) modeUser Guidelines•If the command is

Address Table CommandsPage 55User GuidelinesBefore defining forbidden ports, the Multicast group should be registered.ExampleThe following example con

Page 56 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxbridge multicast forward-all {add | remove} {ethernet interface-list | port

Address Table CommandsPage 57Default ConfigurationThis setting is disabled.Command ModeInterface Configuration (VLAN) modeUser Guidelines•IGMP snoopin

Page 58 Allied Telesis AT-8000GS Command Line Interface User’s Guideclear bridgeThe clear bridge Privileged EXEC mode command removes any learned ent

Address Table CommandsPage 59User GuidelinesThere are no user guidelines for this command.ExampleThe following example forwards all packets from port

Page 6 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow interfaces configuration...

Page 60 Allied Telesis AT-8000GS Command Line Interface User’s Guideno port security maxParameters•max-addr— Maximum number of addresses that can be

Address Table CommandsPage 61ExampleThe following example adds the MAC-layer address 66:66:66:66:66:66 to port 1/g1.show bridge address-tableThe show

Page 62 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow bridge address-table staticThe show bridge address-table static Privileged E

Address Table CommandsPage 63Parameters•vlan — Specifies a valid VLAN, such as VLAN 1.• interface — A valid Ethernet port.• port-channel-number — A va

Page 64 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow bridge multicast address-tableThe show bridge multicast address-table Privil

Address Table CommandsPage 65ExamplesThe following examples display Multicast MAC address and IP Address Table information.console# show bridge multic

Page 66 Allied Telesis AT-8000GS Command Line Interface User’s GuideNoteA Multicast MAC address maps to multiple IP addresses as shown above.show bri

Address Table CommandsPage 67Syntaxshow bridge multicast filtering vlan-idParameters•vlan-id — VLAN ID value.Default ConfigurationThis command has no

Page 68 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow bridge multicast unregisteredUse The show bridge multicast unregistered User

Address Table CommandsPage 69show ports securityThe show ports security Privileged EXEC mode command displays the port-lock status.Syntaxshow ports se

Page 7ip name-server ...

Page 70 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow ports security addressesThe show ports security addresses Privileged EXEC mo

Address Table CommandsPage 71The following example displays dynamic addresses in currently locked port 1/g1.console# show ports security addresses eth

Page 72 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 5. Clock Commandsclock setThe clock set Privileged EXEC mode command manu

Clock CommandsPage 73Default ConfigurationNo external clock sourceCommand ModeGlobal Configuration modeUser GuidelinesThere are no user guidelines for

Page 74 Allied Telesis AT-8000GS Command Line Interface User’s Guideclock summer-timeThe clock summer-time Global Configuration mode command configur

Clock CommandsPage 75User GuidelinesIn both the date and recurring forms of the command, the first part of the command specifies when summer time begi

Page 76 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example defines the authentication key for SNTP.sntp authent

Clock CommandsPage 77Default ConfigurationNo keys are trusted.Command ModeGlobal Configuration modeUser GuidelinesThe command is relevant for both rec

Page 78 Allied Telesis AT-8000GS Command Line Interface User’s Guidesntp broadcast client enableThe sntp broadcast client enable Global Configuration

Clock CommandsPage 79User GuidelinesThe sntp client poll timer Global Configuration mode command determines polling time.Use the sntp client enable (I

Page 8 Allied Telesis AT-8000GS Command Line Interface User’s Guidelldp tx-delay ...

Page 80 Allied Telesis AT-8000GS Command Line Interface User’s GuideSyntaxsntp unicast client enableno sntp unicast client enableParametersThis comma

Clock CommandsPage 81ExampleThe following example enables polling for Simple Network Time Protocol (SNTP) predefined Unicast clients. sntp serverThe s

Page 82 Allied Telesis AT-8000GS Command Line Interface User’s GuideExampleThe following example configures the device to accept SNTP traffic from th

Clock CommandsPage 83show sntp configurationThe show sntp configuration Privileged EXEC mode command shows the configuration of the Simple Network Tim

Page 84 Allied Telesis AT-8000GS Command Line Interface User’s Guideshow sntp statusThe show sntp status Privileged EXEC mode command shows the statu

Clock CommandsPage 85176.1.8.179 Unknown 12:17.17.987 PDT Feb 19 2009 8.98 189.19Anycast server:Server Interface Status Last response Offset Delay[mS

Page 86 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 6. Configuration and Image File CommandscopyThe copy Privileged EXEC mode

Configuration and Image File CommandsPage 87Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser Guidel

Page 88 Allied Telesis AT-8000GS Command Line Interface User’s GuideCopying a Configuration File from a Server to the Startup ConfigurationTo copy a

Configuration and Image File CommandsPage 89User GuidelinesThere are no user guidelines for this command.ExampleThe following example displays the lis

Page 9show power inline...

Page 90 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command ModePrivil

Configuration and Image File CommandsPage 91Syntaxshow running-configParametersThis command has no arguments or keywords.Default ConfigurationThis com

Page 92 Allied Telesis AT-8000GS Command Line Interface User’s GuideDefault ConfigurationThis command has no default configuration.Command ModePrivil

Configuration and Image File CommandsPage 93User GuidelinesThere are no user guidelines for this command.ExampleThe following example displays the act

Page 94 Allied Telesis AT-8000GS Command Line Interface User’s GuideChapter 7. DHCP Snooping Commandsip dhcp snoopingThe ip dhcp snooping Global Conf

DHCP Snooping CommandsPage 95Command ModeGlobal Configuration modeUser GuidelinesDHCP snooping must be first globally enabled before enabling DHCP sno

Page 96 Allied Telesis AT-8000GS Command Line Interface User’s Guideip dhcp snooping information option allowed-untrustedThe ip dhcp snooping informa

DHCP Snooping CommandsPage 97User GuidelinesThere are no user guidelines for this command.ExampleThe following example configures the switch to verify

Page 98 Allied Telesis AT-8000GS Command Line Interface User’s GuideParameters•seconds — Specify, in seconds, the update frequency (Range: 600 - 8640

DHCP Snooping CommandsPage 99The entry is displayed in the show commands as a ‘DHCP Snooping entry’.ExampleThe following example configures the DHCP s