Allied-telesis AT-S63 Bedienungsanleitung Seite 46
- Seite / 412
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 2: Port Parameters
46 Section I: Basic Operations
Ingress Unknown Unicast Filter
Use this parameter to configure a port to forward or discard unknown
ingress unicast packets. The possible settings are:
Enabled - The port discards unknown ingress unicast packets.
Disabled - The port forwards unknown ingress unicast packets. This is
the default setting.
Egress Unknown Unicast Filter
Use this parameter to configure a port to forward or discard unknown
egress unicast packets. The possible settings are:
Enabled - The port discards unknown egress unicast packets.
Disabled - The port forwards unknown egress unicast packets. This is
the default setting.
Ingress Unknown Multicast Filter
Use this parameter to configure a port to forward or discard unknown
ingress multicast packets. Possible settings are:
Enabled - The port discards unknown ingress multicast packets.
Disabled - The port forwards unknown ingress multicast packets. This
is the default setting.
Egress Unknown Multicast Filter
Use this parameter to configure a port to forward or discard unknown
egress multicast packets. Possible settings are:
Enabled - The port discards unknown egress multicast packets.
Disabled - The port forwards unknown egress multicast packets. This
is the default setting.
Flow Control
Sets flow control on a port. This option only applies to ports operating
in full-duplex mode. A switch port uses flow control to control the flow
of ingress packets. The switch sends a special pause packet to stop
the end node from sending frames. The pause packet notifies the end
node to stop transmitting for a specified period of time. Possible
settings are:
Disabled - No flow control on the port. This is the default.
Enabled - Flow control is activated.
Back Pressure
Use this parameter to set backpressure on a port. This option only
appears for ports operating in half-duplex mode. A port uses
backpressure to control the flow of ingress packets. Possible settings
are:
Enabled - Backpressure is enabled.
- Web Browser 1
- User’s Guide 1
- Contents 3
- How This Guide is Organized 16
- Section VI: Port Security 17
- Product Documentation 18
- Where to Go First 19
- Starting a Management Session 19
- Document Conventions 20
- Contacting Allied Telesis 21
- Basic Operations 23
- Basic Switch Parameters 25
- Displaying System Information 38
- Port Parameters 41
- Configuring Port Parameters 42
- Chapter 2: Port Parameters 44
- Figure 9. Port Status Page 50
- Parameters” on page 42 50
- Displaying Port Statistics 51
- Chapter 3: Enhanced Stacking 56
- Chapter 4: SNMPv1 and SNMPv2c 64
- Chapter 5: MAC Address Table 74
- Changing the Aging Time 81
- Creating a Static Port Trunk 84
- Chapter 6: Static Port Trunks 86
- Modifying a Static Port Trunk 88
- Deleting a Port Trunk 90
- Displaying the Port Trunks 91
- The ports of the trunk 92
- Port Mirroring 93
- Creating a Port Mirror 94
- Section I: Basic Features 95 95
- Modifying a Port Mirror 97
- Disabling a Port Mirror 98
- Deleting a Port Mirror 99
- Displaying the Port Mirror 100
- Advanced Operations 101
- File System 103
- Chapter 8: File System 104
- File Downloads and Uploads 109
- Downloading a File 110
- Uploading a File 114
- Event Logs and Syslog Client 117
- Working with the Event Logs 118
- Clearing an 124
- Event Log 124
- Modifying the 125
- Event Log Full 125
- Saving an Event 126
- Log to a File 126
- Configuring a 127
- Syslog Output 127
- Definition 127
- Viewing a Syslog 130
- Output Definition 130
- Modifying a 130
- Deleting a Syslog 131
- Classifiers 133
- Configuring a Classifier 134
- Chapter 11: Classifiers 136
- Modifying a Classifier 140
- Deleting a Classifier 142
- Displaying the Classifiers 143
- Class of Service 153
- Configuring CoS 154
- Chapter 13: Class of Service 156
- Configuring Egress Scheduling 158
- Displaying the CoS Settings 159
- Managing Flow Groups 164
- Modifying a Flow 167
- Deleting a Flow 168
- Displaying the 168
- Flow Groups 168
- Traffic Class 174
- Deleting a Traffic 176
- Traffic Classes 176
- Managing Policies 178
- Denial of Service Defenses 185
- Displaying the DoS Settings 189
- IGMP Snooping 191
- Configuring IGMP Snooping 192
- Chapter 16: IGMP Snooping 194
- 200 Section III: SNMPv3 200
- Section III: SNMPv3 203 203
- Section III: SNMPv3 205 205
- Section III: SNMPv3 207 207
- Deleting a User 209
- Table Entry 209
- Modifying a User 210
- Section III: SNMPv3 211 211
- Section III: SNMPv3 213 213
- Section III: SNMPv3 215 215
- Deleting a View 217
- Modifying a View 217
- 1.3.6.1.2.1.2.2.1.0.3 218
- Section III: SNMPv3 219 219
- Creating an 220
- Access Table 220
- Chapter 17: SNMPv3 222
- 222 Section III: SNMPv3 222
- Modifying an 224
- Section III: SNMPv3 225 225
- Creating a 227
- SecurityToGroup 227
- 228 Section III: SNMPv3 228
- 230 Section III: SNMPv3 230
- 232 Section III: SNMPv3 232
- 234 Section III: SNMPv3 234
- Notify Table 236
- Section III: SNMPv3 237 237
- Section III: SNMPv3 239 239
- 240 Section III: SNMPv3 240
- Modifying Target 242
- Address Table 242
- Section III: SNMPv3 243 243
- Creating a Target 245
- Parameters Table 245
- 246 Section III: SNMPv3 246
- Deleting a Target 248
- 250 Section III: SNMPv3 250
- Community 252
- Section III: SNMPv3 253 253
- Section III: SNMPv3 255 255
- Section III: SNMPv3 257 257
- Section III: SNMPv3 259 259
- Displaying View 260
- Table Entries 260
- Displaying Access 261
- Displaying 262
- Displaying Notify 263
- Displaying Target 264
- Section III: SNMPv3 267 267
- Spanning Tree Protocols 269
- Protocols 271
- Configuring STP 274
- Port Settings 277
- STP Settings 278
- 4. Click View 279
- Resetting STP to 280
- Settings 280
- Configuring RSTP 282
- Configuring 285
- RSTP Port 285
- Displaying RSTP 286
- Resetting RSTP 289
- Chapter 19 291
- Enabling MSTP 292
- Configuring MSTP 294
- Configuring the 297
- CIST Priority 297
- Managing MSTIs 298
- External path cost 302
- 10 Mbps 20,000 305
- 100 Mbps 20,000 305
- 1000 Mbps 2,000 305
- Virtual LANs 313
- 314 Section V: VLANs 314
- 316 Secton V: Virtual LANs 316
- 318 Secton V: Virtual LANs 318
- 320 Secton V: Virtual LANs 320
- 322 Secton V: Virtual LANs 322
- Selecting a VLAN Mode 324
- Secton V: Virtual LANs 325 325
- Secton V: Virtual LANs 327 327
- Secton V: Virtual LANs 329 329
- 330 Secton V: Virtual LANs 330
- Configuring GVRP 332
- Section V: Virtual LANs 333 333
- Section V: Virtual LANs 335 335
- Displaying the GVRP Database 337
- Table 11 338
- Section V: Virtual LANs 339 339
- 340 Section V: Virtual LANs 340
- 342 Section V: Virtual LANs 342
- 344 Section V: Virtual LANs 344
- 346 Section VI: Port Security 346
- Configuring Port Security 348
- Section VI: Port Security 349 349
- 350 Section VI: Port Security 350
- 352 Section VI: Port Security 352
- Setting Port Roles 354
- Section VI: Port Security 355 355
- Section VI: Port Security 357 357
- Section VI: Port Security 359 359
- 360 Section VI: Port Security 360
- 362 Section VI: Port Security 362
- 364 Section VI: Port Security 364
- 366 Section VI: Port Security 366
- 368 Section VI: Port Security 368
- Accounting 370
- Management Security 371
- Encryption Keys, PKI, and SSL 373
- Displaying the SSL Settings 379
- Secure Shell (SSH) 381
- Configuring SSH 382
- Displaying the SSH Settings 384
- TACACS+ and RADIUS Protocols 387
- Chapter 27 399
- Creating an ACE 402
- Modifying an ACE 404
- Deleting an ACE 405
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-S63
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern