Allied-telesis AT-S63 Bedienungsanleitung Seite 192
- Seite / 412
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 16: IGMP Snooping
192 Section II: Advanced Operations
Configuring IGMP Snooping
To configure IGMP snooping, perform the following procedure:
1. From the home page, select Configuration.
2. From the Configuration menu, select the Multicast option.
The Multicast page is displayed with the IGMP tab selected by default,
as shown in Figure 72.
Figure 72. IGMP Tab (Configuration)
3. Configure the following parameters as necessary.
Enable IGMP Snooping Status
Enables and disables IGMP snooping on the switch. A check in the
box indicates that IGMP snooping is enabled.
Multicast Host Topology
Defines whether there is only one host node per switch port or multiple
host nodes per port. Possible settings are Edge (Single-Host/Port) and
Intermediate (Multi-Host/Port).
The Single-Host/Port (Edge) setting is appropriate when there is only
one host node connected to each port on the switch. This setting
causes the switch to immediately stop sending multicast packets out a
switch port when a host node signals its desire to leave a multicast
group by sending a leave request or when the host node stops sending
reports and times out. The switch forwards the leave request to the
router and simultaneously ceases transmission of any further multicast
packets out the port where the host node is connected.
- Web Browser 1
- User’s Guide 1
- Contents 3
- How This Guide is Organized 16
- Section VI: Port Security 17
- Product Documentation 18
- Where to Go First 19
- Starting a Management Session 19
- Document Conventions 20
- Contacting Allied Telesis 21
- Basic Operations 23
- Basic Switch Parameters 25
- Displaying System Information 38
- Port Parameters 41
- Configuring Port Parameters 42
- Chapter 2: Port Parameters 44
- Figure 9. Port Status Page 50
- Parameters” on page 42 50
- Displaying Port Statistics 51
- Chapter 3: Enhanced Stacking 56
- Chapter 4: SNMPv1 and SNMPv2c 64
- Chapter 5: MAC Address Table 74
- Changing the Aging Time 81
- Creating a Static Port Trunk 84
- Chapter 6: Static Port Trunks 86
- Modifying a Static Port Trunk 88
- Deleting a Port Trunk 90
- Displaying the Port Trunks 91
- The ports of the trunk 92
- Port Mirroring 93
- Creating a Port Mirror 94
- Section I: Basic Features 95 95
- Modifying a Port Mirror 97
- Disabling a Port Mirror 98
- Deleting a Port Mirror 99
- Displaying the Port Mirror 100
- Advanced Operations 101
- File System 103
- Chapter 8: File System 104
- File Downloads and Uploads 109
- Downloading a File 110
- Uploading a File 114
- Event Logs and Syslog Client 117
- Working with the Event Logs 118
- Clearing an 124
- Event Log 124
- Modifying the 125
- Event Log Full 125
- Saving an Event 126
- Log to a File 126
- Configuring a 127
- Syslog Output 127
- Definition 127
- Viewing a Syslog 130
- Output Definition 130
- Modifying a 130
- Deleting a Syslog 131
- Classifiers 133
- Configuring a Classifier 134
- Chapter 11: Classifiers 136
- Modifying a Classifier 140
- Deleting a Classifier 142
- Displaying the Classifiers 143
- Class of Service 153
- Configuring CoS 154
- Chapter 13: Class of Service 156
- Configuring Egress Scheduling 158
- Displaying the CoS Settings 159
- Managing Flow Groups 164
- Modifying a Flow 167
- Deleting a Flow 168
- Displaying the 168
- Flow Groups 168
- Traffic Class 174
- Deleting a Traffic 176
- Traffic Classes 176
- Managing Policies 178
- Denial of Service Defenses 185
- Displaying the DoS Settings 189
- IGMP Snooping 191
- Configuring IGMP Snooping 192
- Chapter 16: IGMP Snooping 194
- 200 Section III: SNMPv3 200
- Section III: SNMPv3 203 203
- Section III: SNMPv3 205 205
- Section III: SNMPv3 207 207
- Deleting a User 209
- Table Entry 209
- Modifying a User 210
- Section III: SNMPv3 211 211
- Section III: SNMPv3 213 213
- Section III: SNMPv3 215 215
- Deleting a View 217
- Modifying a View 217
- 1.3.6.1.2.1.2.2.1.0.3 218
- Section III: SNMPv3 219 219
- Creating an 220
- Access Table 220
- Chapter 17: SNMPv3 222
- 222 Section III: SNMPv3 222
- Modifying an 224
- Section III: SNMPv3 225 225
- Creating a 227
- SecurityToGroup 227
- 228 Section III: SNMPv3 228
- 230 Section III: SNMPv3 230
- 232 Section III: SNMPv3 232
- 234 Section III: SNMPv3 234
- Notify Table 236
- Section III: SNMPv3 237 237
- Section III: SNMPv3 239 239
- 240 Section III: SNMPv3 240
- Modifying Target 242
- Address Table 242
- Section III: SNMPv3 243 243
- Creating a Target 245
- Parameters Table 245
- 246 Section III: SNMPv3 246
- Deleting a Target 248
- 250 Section III: SNMPv3 250
- Community 252
- Section III: SNMPv3 253 253
- Section III: SNMPv3 255 255
- Section III: SNMPv3 257 257
- Section III: SNMPv3 259 259
- Displaying View 260
- Table Entries 260
- Displaying Access 261
- Displaying 262
- Displaying Notify 263
- Displaying Target 264
- Section III: SNMPv3 267 267
- Spanning Tree Protocols 269
- Protocols 271
- Configuring STP 274
- Port Settings 277
- STP Settings 278
- 4. Click View 279
- Resetting STP to 280
- Settings 280
- Configuring RSTP 282
- Configuring 285
- RSTP Port 285
- Displaying RSTP 286
- Resetting RSTP 289
- Chapter 19 291
- Enabling MSTP 292
- Configuring MSTP 294
- Configuring the 297
- CIST Priority 297
- Managing MSTIs 298
- External path cost 302
- 10 Mbps 20,000 305
- 100 Mbps 20,000 305
- 1000 Mbps 2,000 305
- Virtual LANs 313
- 314 Section V: VLANs 314
- 316 Secton V: Virtual LANs 316
- 318 Secton V: Virtual LANs 318
- 320 Secton V: Virtual LANs 320
- 322 Secton V: Virtual LANs 322
- Selecting a VLAN Mode 324
- Secton V: Virtual LANs 325 325
- Secton V: Virtual LANs 327 327
- Secton V: Virtual LANs 329 329
- 330 Secton V: Virtual LANs 330
- Configuring GVRP 332
- Section V: Virtual LANs 333 333
- Section V: Virtual LANs 335 335
- Displaying the GVRP Database 337
- Table 11 338
- Section V: Virtual LANs 339 339
- 340 Section V: Virtual LANs 340
- 342 Section V: Virtual LANs 342
- 344 Section V: Virtual LANs 344
- 346 Section VI: Port Security 346
- Configuring Port Security 348
- Section VI: Port Security 349 349
- 350 Section VI: Port Security 350
- 352 Section VI: Port Security 352
- Setting Port Roles 354
- Section VI: Port Security 355 355
- Section VI: Port Security 357 357
- Section VI: Port Security 359 359
- 360 Section VI: Port Security 360
- 362 Section VI: Port Security 362
- 364 Section VI: Port Security 364
- 366 Section VI: Port Security 366
- 368 Section VI: Port Security 368
- Accounting 370
- Management Security 371
- Encryption Keys, PKI, and SSL 373
- Displaying the SSL Settings 379
- Secure Shell (SSH) 381
- Configuring SSH 382
- Displaying the SSH Settings 384
- TACACS+ and RADIUS Protocols 387
- Chapter 27 399
- Creating an ACE 402
- Modifying an ACE 404
- Deleting an ACE 405
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-S63
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.271 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern