Allied-telesis AT-WL2411 Bedienungsanleitung Seite 166
- Seite / 236
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Access Point Maintenance
166
Upgrading the Firmware
The procedures in this section explain how to upgrade the firmware on
the AT-WL2411 to Version 1.80.
The current access point configuration information, such as IP address,
should be retained when the new firmware is installed. However,
keeping backup records of configuration settings is recommended.
You can install the firmware release using the following methods:
❑ Serial connection
❑ TFTP transfer via a Telnet session
❑ Web browser session (only available on Version 1.72 and later
releases)
To upgrade the firmware, you must first download the firmware release
onto your local computer. The latest version of the AT-WL2411 firmware
is available from the Allied Telesyn Web site at www.alliedtelesyn.com.
Using a Serial
Connection
To upgrade the firmware using a serial connection, you must have an RS-
232 null-modem cable connecting the wireless access point to your
computer and a communications program such as HyperTerminal
installed on your computer.
To upload the firmware, perform the following procedure:
1. Configure the following parameters on your communications
software:
Baud rate 9600
Data bits 8
Parity none
Stop bit 1
Flow control none
2. Reboot the wireless access point and enter the wireless access point
monitor by pressing any key within 5 seconds when prompted. The
ap> prompt appears.
3. Type srvc at the prompt and press C and press <Enter>.
4. Type the service password. The default password is EV98203S
(case-sensitive). The service> prompt appears.
5. Type fd at the prompt and press <Enter>. The file directory appears.
- Installation 1
- User’s Guide 1
- Statement 3
- Table of Contents 5
- How This Guide is Organized 11
- Document Conventions 13
- Product Description 17
- Hardware Features 18
- 10 Mbps 19
- Twisted Pair 19
- Ethernet Port 19
- Firmware Features 21
- Using Multiple 23
- APs and 23
- Roaming End 23
- Verifying Package Contents 29
- Installing the Access Point 30
- 6. Replace the door 34
- Warranty Registration 35
- Configuration Overview 37
- Using a Serial Connection 38
- Assigning an IP Address 41
- Using a Web Browser 43
- Using a Telnet Session 47
- Using SNMP 48
- Configuring the Ethernet 51
- Supported DHCP Server Options 58
- About Network 59
- Address 59
- Translation 59
- Send ARP 61
- Requests 61
- Configuring Ethernet Filters 64
- Using Ethernet 66
- Setting Filter 73
- Expressions 74
- About the Root 81
- Bridging Layer 83
- Functions 83
- Network Organization 83
- Forwarding 83
- Switch Support 84
- Flooding Configurations 84
- Pending Messages 84
- Filtering Options 84
- Secondary LANs 85
- Configuring Global Parameters 86
- About IP Tunnels 91
- Internet Group 93
- Management 93
- Protocol (IGMP) 93
- Originating IP 94
- Outbound Frames 97
- Inbound Frames 98
- Configuring the Spanning Tree 100
- Configuring IP 101
- Address List 101
- Configuring IP Tunnel Filters 102
- Using IP Tunnel 103
- Frame Type 103
- Subtype Filters 106
- Predefined 106
- Customizing 107
- Configuring the IEEE 802.11b 111
- Ethernet 112
- 21XXT013.eps 116
- Ethernet Ethernet 116
- Primary LAN Secondary LAN 125
- Designated 125
- Configuring 126
- 802.11b Point 126
- Parameters 126
- About the Radios 133
- Configuring Security 135
- Understanding Security 136
- Enabling Access Methods 139
- Setting Up Logins 143
- Configuring the 144
- Access Point to 144
- Use a Password 144
- Changing the 146
- Default Login 146
- Configuring 802.1x Security 154
- About Secure 155
- IAPP and Secure 155
- Wireless Hops 155
- Access Point as 156
- Authenticator 156
- Access Point Maintenance 159
- Monitoring the Access Point 160
- Viewing Port 161
- Statistics 161
- Viewing the 162
- Configuration 162
- Viewing 163
- Information 163
- About the 163
- Access Point 163
- Upgrading the Firmware 166
- Using TFTP via 169
- Using a Web 170
- Browser 170
- Interface 170
- Troubleshooting 173
- Communication 175
- Security 177
- Advanced Configuration 185
- Commands 185
- Understanding 186
- Segments 186
- Entering the 187
- SR Purpose 190
- Using Service Mode Commands 191
- FFR f (s) 192
- FFR access pointBOOT.PRG 1 192
- Using Test Mode Commands 193
- Using Console Command Mode 195
- Fb ib: id: 196
- Using Sdvars Commands 199
- Using TFTP Commands 204
- Appendix A 209
- Global Flooding 210
- Menu Defaults 210
- Global RF 211
- Advanced 213
- Filters Menu 213
- Defaults 213
- IP Tunnels Menu Defaults 214
- Security Menu Defaults 216
- Technical Specifications 219
- Other Specifications 220
- Emission Information 221
- Glossary 229
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-WL2411
(114 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern