Allied-telesis AT-S81 Bedienungsanleitung Seite 148
- Seite / 360
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 11: IGMP Snooping
148 Section II: Menus Interface
Configuring IGMP
To configure IGMP, perform the following procedure:
1. From the Main Menu, type A to select Advanced Switch
Configuration.
The Advanced Switch Configuration Menu is shown in Figure 4 on
page 32.
2. From the Advanced Switch Configuration Menu, type I to select IGMP
Snooping Configuration.
The IGMP Configuration Menu is shown in Figure 36.
Figure 36. IGMP Configuration Menu
3. Type E to select Enable/Disable IGMP Snooping.
The following prompt is displayed:
Enable or Disable IGMP snooping (E/D)>
4. Type E to enable IGMP snooping or D to disable IGMP snooping.
5. If you are activating the feature, type S to Set Age-Out Timer.
The following prompt is displayed:
AT-8000/8POE Local Management System
Advanced Switch Configuration -> IGMP Configuration Menu
IGMP Snooping Status: Disabled
IGMP Snooping Age-Out Timer: 280 seconds
VLAN ID Multicast group address
------- ------------------------
----------------------- <COMMAND> -----------------------------
[N]ext Page [E]nable/Disable IGMP Snooping
[P]revious Page [S]et Age-Out Timer
[V]iew group members [Q]uit to previous menu
Command>
- Management 1
- Software 1
- User’s Guide 1
- Contents 3
- Contacting Allied Telesis 15
- Overview 17
- Management Overview 18
- Local Connection 19
- Remote Connection 20
- Management Access Level 21
- Chapter 1: Overview 22
- Using the Menus Interface 23
- Interface 25
- TERMINAL PORT 26
- Enter system name> 37
- Enter system location> 37
- Enter system contact> 37
- Enter current password> 40
- Enter old password> 40
- Enter new password> 40
- Retype new password> 41
- Viewing Switch Information 47
- Rebooting the Switch 50
- Enter new timeout value> 53
- Figure 14. Ping Results 54
- Chapter 4: Port Configuration 62
- Enabling and Disabling a Port 64
- Enter new mode for port 65
- (a/h/H/F/f/t/T)> 65
- > (E/D)> 67
- Chapter 5 71
- SNMP Overview 72
- Default SNMP 73
- Community 73
- Chapter 5: SNMP 74
- Enabling Authentication Traps 75
- Enter read community name> 76
- Modifying a Trap 78
- Receiver 78
- Deleting a Trap 79
- Port Trunking Overview 82
- LACP Trunks 84
- Chapter 6: Port Trunking 88
- LACP Port 92
- Priority 92
- Enter trunk group number> 95
- Set trunk group 95
- status (A/P/M/D)> 95
- Port Mirroring Overview 98
- Chapter 7: Port Mirroring 100
- Power Over Ethernet 103
- PoE Overview 104
- PoE Device 105
- Configuring PoE 107
- PoE Port’s 108
- Admin Setting 108
- Changing the 108
- Setting the PoE 109
- Port’s Priority 109
- Virtual LANs and GVRP 111
- VLAN Features 112
- VLAN Overview 114
- Tagged Port Members 115
- Untagged Port Members 115
- Incoming Frames 115
- Outgoing Frames 116
- AT-8000/8POE 117
- Tagged VLAN 119
- Working with VLANS 121
- Configuring the 124
- Port PVID 124
- Displaying the 125
- Changing the VLAN Name 127
- Enter VLAN ID > 128
- Resetting to the 129
- Default VLAN 129
- AT-9000/24 131
- Enabling or 132
- Disabling GVRP 132
- Quality of Service (QoS) 133
- QoS Overview 134
- Configuring CoS 140
- IGMP Snooping 145
- IGMP Snooping Overview 146
- Configuring IGMP 148
- Enter age out time> 149
- Viewing the Multicast Groups 150
- Chapter 11: IGMP Snooping 152
- Chapter 12 153
- RSTP Overview 154
- Path Costs and Port Costs 155
- Port Priority 156
- Point-to-Point and Edge Ports 157
- Point-to-Point Ports 158
- (Full-duplex Mode) 158
- Mixed STP and 159
- RSTP Networks 159
- Rapid Spanning 160
- Tree and VLANs 160
- Enabling or Disabling RSTP 161
- Enter bridge priority> 164
- Enter bridge hello time> 164
- Enter bridge maximum age> 165
- Configuring STP Compatibility 166
- Basic RSTP Port 167
- Settings 167
- Advanced RSTP 169
- Port Settings 169
- Displaying the RSTP Topology 172
- 802.1x Network Access Control 175
- Authentication 177
- Authenticator 177
- Network Access 179
- Guidelines 179
- Switch A 181
- Switch B 181
- Enter port number> 183
- Enter NAS ID > 183
- Chapter 14 187
- RADIUS Overview 188
- Configuring the RADIUS Server 189
- Broadcast Storm Control 193
- MAC Address Tables 197
- MAC Address Overview 198
- MAC Addresses 200
- Setting the Age-Out Time 204
- Working With System Files 205
- Enter file name> 208
- Enter retry count> 208
- Download file? (Y/N)> 208
- Uploading the 209
- Configuration 209
- Downloading a 211
- Section II 213
- Chapter 18 215
- Switch’s IP Address 216
- Web Browser Tools 219
- Basic Switch Parameters 221
- System Contact 226
- 3. Click Apply 226
- Server and SNMP settings 228
- Configuring SNTP 232
- Viewing System Information 233
- Rebooting a Switch 235
- Pinging a Remote System 236
- Working with the System Log 238
- Sending the 239
- System Log to a 239
- Remote Server 239
- Port Configuration 243
- Displaying Port Statistics 250
- Chapter 21 253
- Chapter 21: SNMP 254
- Working with Trap Receivers 256
- 2. Click Restore 257
- Port Trunking 259
- Setting Up a Port Trunk 260
- Modifying a Port 261
- Disabling a Port 261
- Chapter 22: Port Trunking 262
- Setting Up an LACP Trunk 263
- Viewing the 264
- LACP Group 264
- Disabling an 265
- LACP Trunk 265
- Port Mirroring 267
- Configuring Port Mirroring 268
- Disabling Port Mirroring 269
- Chapter 23: Port Mirroring 270
- Virtual LANs 275
- Creating a VLAN 276
- Chapter 25: Virtual LANs 278
- Displaying the VLANs 280
- Figure 85 281
- Modifying a VLAN 282
- Deleting a VLAN 284
- Deleting All VLANs 285
- Enabling or Disabling GVRP 286
- Chapter 27 293
- Chapter 27: IGMP 296
- Chapter 28 297
- Chapter 28: RSTP 298
- 4. Click Apply 299
- Basic RSTP Configuration 300
- Viewing the RSTP Topology 305
- Chapter 30 311
- Configuring the RADIUS Client 312
- Setting the Aging Time 321
- Section III 329
- Formatting 333
- Conventions 333
- User EXEC 334
- Command Mode 334
- Privileged EXEC 335
- 336 Section I: Basic Features 336
- Port Mirroring Example 338
- VLAN Example 340
- Section I: Basic Features 341 341
- Command Formatting 342
- Section I: Basic Features 343 343
- 344 Section I: Basic Features 344
- AT-S81 Default Settings 345
- Basic Switch Default Settings 346
- SNMP Default Settings 348
- Status Enabled 349
- Mode Auto 349
- Flow Ctrl Enabled 349
- Quality of Service 350
- RSTP Default Settings 352
- Settings Default 354
- Server IP Address 0.0.0.0 354
- Response Time 10 seconds 354
- Maximum Retransmissions 3 354
- Threshold Low 355
- 356 Section I: Basic Features 356
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-S81
(326 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern