Allied-telesis AT-EN646MOD Enclosure Bedienungsanleitung

613-000731 Rev AEnclosure and Intelligent Multiservice Gateways _________________AT-EN646MOD EnclosureInstallation Guide

AT-EN646MOD Installation Guide10 Chapter 3: Enclosure InstallationCheck Package ContentsThe following items are included in the enclosure package. If

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 11Mount the EnclosureTo mount the AT-EN646MOD enclosure, perform the following procedu

AT-EN646MOD Installation Guide12 Chapter 3: Enclosure InstallationInstall the Grounding Plate1. Remove the grounding plate and the self-tapping screws

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 13Figure 6. Aligning the Ground Plate

AT-EN646MOD Installation Guide14 Chapter 3: Enclosure InstallationInstall the Fiber Clips onto the Grounding Plate1. From the accessory kit, take out

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 15Option 1 - Install the Dielectric Drop CableSecuring the Fiber Optic Drop CableTo in

AT-EN646MOD Installation Guide16 Chapter 3: Enclosure InstallationFigure 9. Positioning the Cable11. Tighten the Kepnuts on the strength member clamp

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 1712. Replace the bar, washers, and Kepnuts on the posts of the drop cable clamp and t

AT-EN646MOD Installation Guide18 Chapter 3: Enclosure InstallationInstall the Ground WireThe AT-iMG646MOD must be connected to a good earth ground.Cau

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 19Secure the Entrance (Replace/Seal the Grommet and Install Tie-Down)1. Take the gromm

Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

AT-EN646MOD Installation Guide20 Chapter 3: Enclosure InstallationSecure the Tracer Wire and Aramid YarnNoteAny tracer wire or cable armoring on the f

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 21Option 2 - Install the Armored Drop CableTo install the fiber optic drop cable, perf

AT-EN646MOD Installation Guide22 Chapter 3: Enclosure InstallationNoteMake sure that the fiber optic cable is not secured by either clamp.10. Position

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 23Install the Ground WireThe AT-iMG646MOD must be connected to a good earth ground.Cau

AT-EN646MOD Installation Guide24 Chapter 3: Enclosure InstallationSecure the Entrance (Replace/Seal the Grommet and Install Tie-Down)1. Take the gromm

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 25Splice the Drop Cable and Securing the Fusion Splice Tray1. Locate the fusion splice

AT-EN646MOD Installation Guide26 Chapter 3: Enclosure Installation8. Route the buffer tube from the drop cable to the upper left corner of the splice

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 2712. Strip the SC/UPC pigtail jacket to expose 22.75 in. (58 cm) of fiber.13. Clean t

AT-EN646MOD Installation Guide28 Chapter 3: Enclosure InstallationFigure 24. Splicing Tray - CompleteNoteThe AT-iMG646MOD WAN module has a receive sen

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 29Secure the Optical WireNoteIt is critical that you maintain a minimum fiber bend rad

3Chapter 1: Preface ...

Figure 26. Enclosure Connections at End of Installation

AT-EN646MOD Installation GuideChapter 3: Enclosure Installation 31

AT-EN646MOD Installation Guide32 Chapter 3: Enclosure Installation613-000731 A

Contents4

AT-EN646MOD Installation Guide5Chapter 1PrefaceThis guide contains instructions on how to install the AT-EN646MOD enclosure. This guide is used when t

Preface6web site: www.alliedtelesis.com.Returning Products Products for return or repair must first be assigned a return materials authorization (RMA)

AT-EN646MOD Installation GuideEnclosure Overview 7Chapter 2Enclosure OverviewFeaturesThe AT-EN646MOD enclosure houses and protects the AT-iMG646MOD se

8 Enclosure OverviewThe AT-EN646MOD Interfaces to the NetworkThe AT-EN646MOD allows the AT-iMG646MOD to be installed in an outdoor environment. Refer

9Chapter 3Enclosure InstallationTools RequiredHave the following tools on hand before you install the enclosure: 3/8” drill Drill bit for the size o