Allied-telesis AT-S39 Bedienungsanleitung Seite 159
- Seite / 203
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AT-S39 Command Line Interface User’s Guide
159
SHOW AUTHENTICATION
Syntax
show authentication
Parameters
None.
Description
Use this command to display the following information about the
authenticated protocols on the switch:
❑ The status of your authenticated protocol: enabled or disabled.
❑ The authentication protocol activated on your switch. Either
TACACS+ or RADIUS protocols may be active. The TACACS+
protocol is the default.
❑ The IP addresses of up to 3 authentication servers.
❑ The encryption key for each individual server, if defined.
❑ The global encryption code that applies to all authentication
servers.
❑ The length of the time, in seconds, before the switch assumes the
server cannot respond.
Example
The following command displays authentication protocol information
on your switch:
show authentication
- Command Line 1
- User’s Guide 1
- Table of Contents 3
- Document Conventions 8
- Contacting Allied Telesyn 10
- Management Software Updates 11
- Starting a Command Line 12
- Management Session 12
- Starting a Management Session 13
- Key Features 14
- Command Formatting 15
- Basic Command Line Commands 16
- CLEAR SCREEN 17
- LOGOFF and QUIT 19
- SAVE CONFIGURATION 21
- SET PROMPT 22
- SET SWITCH CONSOLEMODE 23
- SHOW USER 24
- DISABLE DHCPBOOTP 26
- ENABLE DHCPBOOTP 27
- PURGE IP 29
- RESET IP 30
- RESET SYSTEM 31
- RESTART REBOOT 32
- RESTART SWITCH 33
- SET IP ROUTE 36
- SET SYSTEM 37
- SHOW CONFIG 38
- SHOW DHCPBOOTP 39
- SHOW IP ROUTE 41
- SHOW SWITCH 42
- SHOW SYSTEM 43
- Enhanced Stacking Commands 44
- ACCESS SWITCH 45
- SET SWITCH STACKMODE 47
- SHOW REMOTELIST 48
- SNMP Community Strings and 49
- Trap Commands 49
- ADD SNMP COMMUNITY TRAPHOST 50
- CREATE SNMP COMMUNITY 51
- DESTROY SNMP COMMUNITY 53
- RESET SNMP 54
- SET SNMP COMMUNITY 55
- SHOW SNMP 56
- Management Security 57
- DISABLE HTTP SERVER 58
- DISABLE SNMP 59
- ENABLE SNMP 61
- SET PASSWORD MANAGER 62
- SET PASSWORD OPERATOR 63
- SET SWITCH CONSOLETIMER 64
- SHOW HTTP SERVER 65
- RESET SWITCH PORT 67
- SET SWITCH PORT 68
- SHOW SWITCH PORT 73
- SET SWITCH SECURITYMODE 75
- Examples 76
- SET SWITCH THRESHOLD 77
- SHOW SWITCH THRESHOLD 78
- ADD SWITCH TRUNK 80
- CREATE SWITCH TRUNK 81
- DELETE SWITCH TRUNK 83
- DESTROY SWITCH TRUNK 84
- SET SWITCH TRUNK 85
- SHOW SWITCH TRUNK 86
- ADD SWITCH MIRROR 88
- CREATE SWITCH MIRROR 89
- DELETE SWITCH MIRROR 90
- DESTROY SWITCH MIRROR 91
- SET SWITCH MIRROR 92
- SET SWITCH PORT MIRROR 93
- STP Commands 94
- ACTIVATE STP 95
- DISABLE STP 96
- ENABLE STP 97
- RESET STP 98
- SET STP PORT 101
- SHOW STP 103
- RSTP Commands 104
- ACTIVATE RSTP 105
- DISABLE RSTP 106
- ENABLE RSTP 107
- RESET RSTP 108
- SET RSTP 109
- SET RSTP PORT 112
- SHOW RSTP 115
- VLAN Commands 116
- ADD VLAN 117
- Chapter 13: VLAN Commands 118
- DESTROY VLAN 126
- RESET VLAN 127
- SET SWITCH INFILTERING 128
- SET SWITCH MANAGEMENTVLAN 129
- SET SWITCH SWITCHMODE 130
- SET SWITCH VLANMODE 131
- SET SWITCH VLANSTATUS 132
- SHOW VLAN 133
- MAC Address Table Commands 134
- ADD SWITCH FDB 135
- DELETE SWITCH FDB 136
- SET SWITCH AGINGTIMER 137
- SHOW SWITCH FDB 138
- IGMP Snooping Commands 141
- SET IP IGMP 142
- SHOW IP IGMP 144
- Broadcast Frame Control 145
- SET SWITCH BROADCAST 146
- SET SWITCH PORT BCLIMIT 148
- TACACS+ and RADIUS 149
- Commands 149
- ADD RADIUSSERVER 150
- ADD TACACSSERVER 151
- DELETE RADIUSSERVER 152
- DELETE TACACSSERVER 153
- DISABLE AUTHENTICATION 154
- ENABLE AUTHENTICATION 155
- RESET AUTHENTICATION 156
- SET AUTHENTICATION 157
- SHOW AUTHENTICATION 159
- DISABLE PORTACCESS 161
- ENABLE PORTACCESS 162
- SET PORTACCESS 163
- SHOW PORTACCESS 166
- Statistics Commands 167
- RESET SWITCH COUNTER 168
- RESET SWITCH PORT COUNTER 169
- SHOW SWITCH COUNTER 170
- SHOW SWITCH PORT COUNTER 171
- Download and Upload 172
- Command Reference 181
- Basic Switch Commands 183
- Chapter 21: Command Reference 184
- Port Parameter Commands 188
- Port Security Commands 189
- Port Trunking Commands 189
- Port Mirroring Commands 190
- TACACS+ and RADIUS Commands 196
- Download and Upload Commands 199
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-S39
(253 Seiten)
(46 Seiten)
(50 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern