Allied-telesis AT-S39 Bedienungsanleitung Seite 105
- Seite / 203
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AT-S39 Command Line Interface User’s Guide
105
ACTIVATE RSTP
Syntax
activate rstp
Parameters
None
Description
Use this command to designate RSTP as the active spanning tree on the
switch. A spanning tree protocol is active on a switch only if you
designate it as the active spanning tree and enable it.
Note
A change to the active spanning tree protocol will reboot the switch.
Some network traffic may be lost.
When you activate RSTP, the management software displays a prompt
asking if you want to enable the spanning tree. If you select yes, the
management software activates RSTP, resets the switch, and, once the
reset process is completed, enables RSTP. If you select no, the
management software activates RSTP and resets the unit, but does not
enable RSTP. You might select the latter if you want to configure RSTP
parameters before enabling spanning tree.
Example
The following command designates RSTP as the active spanning tree:
activate rstp
- Command Line 1
- User’s Guide 1
- Table of Contents 3
- Document Conventions 8
- Contacting Allied Telesyn 10
- Management Software Updates 11
- Starting a Command Line 12
- Management Session 12
- Starting a Management Session 13
- Key Features 14
- Command Formatting 15
- Basic Command Line Commands 16
- CLEAR SCREEN 17
- LOGOFF and QUIT 19
- SAVE CONFIGURATION 21
- SET PROMPT 22
- SET SWITCH CONSOLEMODE 23
- SHOW USER 24
- DISABLE DHCPBOOTP 26
- ENABLE DHCPBOOTP 27
- PURGE IP 29
- RESET IP 30
- RESET SYSTEM 31
- RESTART REBOOT 32
- RESTART SWITCH 33
- SET IP ROUTE 36
- SET SYSTEM 37
- SHOW CONFIG 38
- SHOW DHCPBOOTP 39
- SHOW IP ROUTE 41
- SHOW SWITCH 42
- SHOW SYSTEM 43
- Enhanced Stacking Commands 44
- ACCESS SWITCH 45
- SET SWITCH STACKMODE 47
- SHOW REMOTELIST 48
- SNMP Community Strings and 49
- Trap Commands 49
- ADD SNMP COMMUNITY TRAPHOST 50
- CREATE SNMP COMMUNITY 51
- DESTROY SNMP COMMUNITY 53
- RESET SNMP 54
- SET SNMP COMMUNITY 55
- SHOW SNMP 56
- Management Security 57
- DISABLE HTTP SERVER 58
- DISABLE SNMP 59
- ENABLE SNMP 61
- SET PASSWORD MANAGER 62
- SET PASSWORD OPERATOR 63
- SET SWITCH CONSOLETIMER 64
- SHOW HTTP SERVER 65
- RESET SWITCH PORT 67
- SET SWITCH PORT 68
- SHOW SWITCH PORT 73
- SET SWITCH SECURITYMODE 75
- Examples 76
- SET SWITCH THRESHOLD 77
- SHOW SWITCH THRESHOLD 78
- ADD SWITCH TRUNK 80
- CREATE SWITCH TRUNK 81
- DELETE SWITCH TRUNK 83
- DESTROY SWITCH TRUNK 84
- SET SWITCH TRUNK 85
- SHOW SWITCH TRUNK 86
- ADD SWITCH MIRROR 88
- CREATE SWITCH MIRROR 89
- DELETE SWITCH MIRROR 90
- DESTROY SWITCH MIRROR 91
- SET SWITCH MIRROR 92
- SET SWITCH PORT MIRROR 93
- STP Commands 94
- ACTIVATE STP 95
- DISABLE STP 96
- ENABLE STP 97
- RESET STP 98
- SET STP PORT 101
- SHOW STP 103
- RSTP Commands 104
- ACTIVATE RSTP 105
- DISABLE RSTP 106
- ENABLE RSTP 107
- RESET RSTP 108
- SET RSTP 109
- SET RSTP PORT 112
- SHOW RSTP 115
- VLAN Commands 116
- ADD VLAN 117
- Chapter 13: VLAN Commands 118
- DESTROY VLAN 126
- RESET VLAN 127
- SET SWITCH INFILTERING 128
- SET SWITCH MANAGEMENTVLAN 129
- SET SWITCH SWITCHMODE 130
- SET SWITCH VLANMODE 131
- SET SWITCH VLANSTATUS 132
- SHOW VLAN 133
- MAC Address Table Commands 134
- ADD SWITCH FDB 135
- DELETE SWITCH FDB 136
- SET SWITCH AGINGTIMER 137
- SHOW SWITCH FDB 138
- IGMP Snooping Commands 141
- SET IP IGMP 142
- SHOW IP IGMP 144
- Broadcast Frame Control 145
- SET SWITCH BROADCAST 146
- SET SWITCH PORT BCLIMIT 148
- TACACS+ and RADIUS 149
- Commands 149
- ADD RADIUSSERVER 150
- ADD TACACSSERVER 151
- DELETE RADIUSSERVER 152
- DELETE TACACSSERVER 153
- DISABLE AUTHENTICATION 154
- ENABLE AUTHENTICATION 155
- RESET AUTHENTICATION 156
- SET AUTHENTICATION 157
- SHOW AUTHENTICATION 159
- DISABLE PORTACCESS 161
- ENABLE PORTACCESS 162
- SET PORTACCESS 163
- SHOW PORTACCESS 166
- Statistics Commands 167
- RESET SWITCH COUNTER 168
- RESET SWITCH PORT COUNTER 169
- SHOW SWITCH COUNTER 170
- SHOW SWITCH PORT COUNTER 171
- Download and Upload 172
- Command Reference 181
- Basic Switch Commands 183
- Chapter 21: Command Reference 184
- Port Parameter Commands 188
- Port Security Commands 189
- Port Trunking Commands 189
- Port Mirroring Commands 190
- TACACS+ and RADIUS Commands 196
- Download and Upload Commands 199
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-S39
(253 Seiten)
(46 Seiten)
(50 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.225 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern