The following table lists the IEEE 802.3u cabling specifications for the AT-PB1000
Series modules when operating in full-duplex mode.
Cabling specifications for half-duplex operation can be found in the PowerBlade Chassis
Installation Guide.
Package Contents
Make sure the following items are included in your package. If any of these items are
missing or damaged, contact your Allied Telesyn sales representative.
❑ One AT-PB1000 Series Gigabit Media Converter
❑ This quick install guide
❑ Warranty card
Installing the Media Converter
1. Remove a blank faceplate from an empty expansion slot on the front of the chassis.
The module can be installed in any slot.
2. Remove the module from the shipping package and store the packaging in a safe
place. Be sure to observe standard ESD precautions.
3. Slide the module into the expansion slot, aligning it with the guiderails, until it
firmly connects to the chassis’ backplane.
4. Secure the module to the chassis by tightening the thumbscrew.
5. Verify that the PR LED on the front of the module is green.
6. Set the ML/LT switch to the LT (Link Test) position.
7. Set the LT BB/LT SA button to either back to back or standalone, depending on your
topology. Refer to the PowerBlade Chassis Installation Guide for additional
information.
8. Remove the dust covers from the fiber optic connectors and connect the data cables.
9. Power ON the end nodes.
Note
End stations used with the media converter must operate with the same duplex
mode (either both full-duplex or both half-duplex mode).
10. Check that the LK LEDs on both ports on the media converter are green. If the
LEDs are OFF, refer to the PowerBlade Chassis Installation Guide for
troubleshooting instructions.
11. If the link test is successful, set the ML/LT switch to the ML (MissingLink) position.
The ML LED should be green. The media converter will not pass network traffic
when a link test is being performed.
12. Repeat this procedure to install additional AT-PB1000 Series modules.
Status LEDs
Fiber Optic Port Specifications
Port Cable Type Maximum Distance
1000Base-SX
All Models 62.5/125
µm multimode fiber 275 m (902 ft)
50/125
µm multimode fiber 550 m (1,804 ft)
1000Base-LX
AT-PB1001/1 62.5/12 5
µm multimode fiber 550 m (1,804 ft)
50/12 5
µm multimode fiber 550 m (1,804 ft)
10/125
µm single-mode fiber 10,000 m (32,800 ft)
AT-PB1001/2 10/125
µm single-mode fiber 20 km (12.4 mi)
AT-PB1001/3 10/125
µm single-mode fiber 50 km (31 mi)
AT-PB1001/4 10/125
µm single-mode fiber 70 km (43.4 mi)
LED Color Description
System LEDs
PR Green Power is applied to the media converter.
ML Green
OFF
The MissingLink feature is activated.
The MissingLink feature is disabled and the media converter is operating in
the link test mode.
Port LEDs
LK Green A link has been established on the port.
Port Cable
Transmitter
Output Power
(dBm avg.)
Wavelength
(nm)
Minimum
Receiver
Sensivity
(dBm avg.)
1000Base-SX
All Models 50/125 or 62.5/125 micron
multimode
-9.5 to -4.0 850 -17.0
1000Base-LX
AT-PB1001 10/125 micron single-mode -9.5 to -3.0 1310 -20.0
50/125 or 62.5/125 micron
multimode
-11.5 to -3.0 1310 -20.0
AT-PB1001/2 10/125 micron single-mode -3.0 to 0.0 1310 -24.0
AT-PB1001/3 10/125 micron single-mode -5.0 to 0.0 1550 -24.0
AT-PB1001/4 10/125 micron single-mode 0.0 to 5.0 1550 -24.0
1 2
(2 Seiten)
(19 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern