Allied-telesis AT-LMC10ST Bedienungsanleitung

AT-LMC10SC AT-LMC10STEthernet Media ConvertersInstallation GuidePN 613-50451-00 Rev B

Welcome to Allied TelesynxContacting Allied Telesyn This section provides Allied Telesyn contact information for technical support as well as sales or

1Chapter 1OverviewThe AT-LMC10 Series Ethernet Media Converters include the following models:❑ AT-LMC10SC❑ AT-LMC10STThe AT-LMC10 Series Ethernet Medi

Overview2Figure 2 AT-LMC10ST Model Converter - Front PanelFigure 3 displays the rear panel of the AT-LMC10 Series Media Converters.Figure 3 AT-LMC10

AT-LMC10SC and AT-LMC10ST Installation Guide3Key FeaturesThe media converters have the following key features:❑ LEDs for unit and port status❑ MDI/MDI

Overview4NoteAfter using the MDI/MDI-X switch to change between the two settings, you must reset the media converter by powering OFF then powering ON

AT-LMC10SC and AT-LMC10ST Installation Guide5Network TopologiesThe AT-LMC10 Series Media Converters can be used in two different types of topologies:

Back-to-Back TopologyFigure 5 illustrates two media converters in a back-to-back configuration.Figure 5 Back-to-Back TopologyRS-232TERMINAL PORTSTATU

7Chapter 2Installing the Media ConverterVerifying the Package ContentsMake sure the following items are included in your package. If any item is missi

Installing the Media Converter8Table 4 10Base-FL Fiber Optic Port Specifications (Full-duplex)Reviewing Safety PrecautionsPlease review the following

AT-LMC10SC and AT-LMC10ST Installation Guide9NoteDo not remove the dust cover from the fiber optic port until you are ready to connect the fiber optic

Copyright © 2004 Allied Telesyn, Inc.960 Stewart Drive, Suite B, Sunnyvale, CA 94085, USAAll rights reserved. No part of this publication may be repro

Installing the Media Converter10Figure 7 12VDC Connector on Rear Panel6. Verify that the PWR LED is green. If the LED is OFF, refer to “Troubleshooti

AT-LMC10SC and AT-LMC10ST Installation Guide11Warranty RegistrationWhen you finish installing the product, you should register your product by complet

13Chapter 3TroubleshootingTroubleshooting GuidelinesFollow the guidelines below to test and troubleshoot the installation in the event a problem occur

Troubleshooting14If the LNK LED for the fiber optic port is OFF, do the following:❑ Verify that then end-node connected to the port is ON and is opera

AT-LMC10SC and AT-LMC10ST Installation Guide15Loopback TestTo check hardware reliability of the media converter, perform the following procedure:1. Po

17Appendix ATechnical SpecificationsPhysicalDimensions: W x D x H10.5 cm x 9.5 cm x 2.5 cm (4.125 in x 3.75 in x 1.0 in)Weight: 0.27 kg (0.60 lbs)Envi

Technical Specifications18Agency CertificationsEMI/RFI: FCC Class B, EN55022 Class B, VCCI Class BElectrical Safety: EN60950 (TUV), UL1950 (cULus), CE

AT-LMC10SC and AT-LMC10ST Installation Guide19Fiber Optic Loss Specifications (Benchmarks)Table 7 Fiber Optic DatalinkModel Fiber Type1Minimum Power

iiiElectrical Safety and Emission ComplianceStandards: This product meets the following standards.U.S. Federal Communications CommissionDeclaration Of

21Appendix BTranslated Electrical Safety and Emission InformationImportant: This appendix contains multiple-language translations for the safety state

Translated Electrical Safety and Emission Information22Standards: This product meets the following standards.U.S. Federal Communications CommissionDec

AT-LMC10SC and AT-LMC10ST Installation Guide23 1RFI Emission EN55022 Class B 2 Immunity EN55024 3 Warning: This product requires shielded cables to

Translated Electrical Safety and Emission Information24Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. 1 Hochfrequenzstöru

AT-LMC10SC and AT-LMC10ST Installation Guide25Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelsesemissio

Translated Electrical Safety and Emission Information26Eisen: Dit product voldoet aan de volgende eisen. 1RFI Emissie EN55022 Klasse B 2 Immuniteit

AT-LMC10SC and AT-LMC10ST Installation Guide27Normes: ce produit est conforme aux normes de suivantes. 1 Emission d'interférences radioélectriqu

Translated Electrical Safety and Emission Information28Standardit: Tämä tuote on seuraavien standardien mukainen. 1 Radioaaltojen häirintä EN55022 Lu

AT-LMC10SC and AT-LMC10ST Installation Guide29Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di radiofreque

Electrical Safety and Emission ComplianceivRFI Emission EN55022 Class B  1Immunity EN55024  2Warning: This product requires shielded cables to comp

Translated Electrical Safety and Emission Information30Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. 1 RFI stråling EN

AT-LMC10SC and AT-LMC10ST Installation Guide31Padrões: Este produto atende aos seguintes padrões. 1 Emissão De Interferência De Radiofrequência EN55

Translated Electrical Safety and Emission Information32Estándares: Este producto cumple con los siguientes estándares. 1Emisión RFI EN55022 Clase B

AT-LMC10SC and AT-LMC10ST Installation Guide33Standarder: Denna produkt uppfyller följande standarder. 1Radiostörning EN55022 Klass B 2 Immunitet E

vAT-LMC10SC and AT-LMC10ST Installation GuideImportante: O Anexo A contém advertências de segurança traduzidas para instalar este equipamento. Quando

viiTable of ContentsElectrical Safety and Emission Compliance...iiiTable of Contents ...

viiiAppendix ATechnical Specifications ......17Physical ...

ixThis guide contains instructions on how to install an AT-LMC10SC or an AT-LMC10ST Fast Ethernet Media Converter.Where to Find Web-based GuidesThe Al