Allied-telesis AT-9000 Series Bedienungsanleitung Seite 182
- Seite / 258
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 16: Setting RADIUS and TACACS+ Clients
182
AAA Authentication Enable Local— Enable or disable
TACACS+ to authenticate users requesting the Privileged Exec
mode. Choose from the following:
Enabled: The TACACS+ determines whether users can
access the Privileged EXEC level using the TACACS+ enable
password. When any TACACS+ server is not available,
authentication is attempted using the password specified using
the ENABLE PASSWORD command in the CLI.
Disabled: The TACACS+ servers do not use its enable
password. Authentication is attempted using the password
specified using the ENABLE PASSWORD command in the
CLI.
AAA Accounting— Select a TACACS+ accounting setting.
Choose from the following:
Start-Stop: A start accounting message is sent at the
beginning of a session, and a stop accounting message is sent
at the end of the session.
Stop-Only: A stop accounting message is sent at the end of
the session.
None: Sending accounting messages is disabled.
5. Click Apply.
The Active Authentication Server field shown on the upper middle of
the page indicates “TACACS+.”
6. Click SAVE
.
Adding a
TACACS+
Server
To add a TACACS+ server, do the following:
1. Click Add
at the bottom of the page.
The TACACS+ Add page is displayed. See Figure 63 on page 183.
- AT-9000 Series 1
- Copyright 2
- Contents 5
- Document Conventions 12
- Contacting Allied Telesis 14
- Browser Interface 15
- Management Sessions 16
- Web Manager Accounts 17
- Starting a Management Session 19
- Figure 3. Login Page 22
- What to Configure First 27
- Saving Your Changes 28
- 5 on page 28 29
- Basic Switch Parameters 31
- Setting System 33
- Time Manually 33
- Setting an SNTP 34
- Setting a Remote Log Server 39
- Displaying and 42
- Setting the Active 42
- Uploading a 43
- Managing User Accounts 44
- Changing a User 45
- Password 45
- Changing the 47
- User Privilege 47
- Rebooting a Switch 49
- Upgrading the Software 50
- Displaying System Information 53
- Setting Port Parameters 57
- Changing the Port Settings 62
- 7. Click Apply 65
- 8. Click SAVE 65
- Setting Port Statistics 71
- Displaying Port Statistics 72
- Receive Statistics 73
- Transmit 75
- Statistics 75
- Interface 77
- Clearing Port Statistics 79
- Setting Port Mirroring 81
- Assigning a Destination Port 85
- Specifying Direction Type 86
- Chapter 7 89
- Setting the MAC Address 95
- Displaying the MAC Address 96
- Multicast MAC 97
- Addresses 97
- Assigning a MAC Address 98
- Multicast 99
- Deleting a MAC Address 101
- Setting LACP 103
- Overview 104
- Displaying LACP Trunks 105
- Chapter 9: Setting LACP 106
- Modifying an LACP Trunk 109
- Adding Static Trunks 117
- Deleting Static Trunks 123
- Chapter 11 125
- Tagged and 127
- Untagged Ports 127
- Displaying VLANs 128
- Adding a VLAN 130
- Modifying VLANs 132
- Assigning a Native VLAN 134
- 7. Click SAVE 135
- Deleting VLANs 136
- Protocol (IGMP) Snooping 137
- Clearing the Routers List 141
- 5. Click Apply 142
- 6. Click SAVE 142
- Disabling IGMP Snooping 143
- Displaying the Routers List 144
- Displaying the Hosts List 145
- Chapter 13 147
- Power Over Ethernet (PoE) 155
- Prioritization 157
- Displaying PoE Settings 158
- PoE Configuration 160
- Security 163
- Interface— Port number 166
- Chapter 16 171
- Server 1 174
- Configuring 175
- Remote Manager 175
- Authentication 175
- Using RADIUS 175
- Adding a 177
- RADIUS Server 177
- Using TACACS+ 179
- Chapter 17 185
- Chapter 18 197
- IP Management 199
- Guidelines 199
- Assigning an IPv4 Address 200
- Assigning a 201
- DHCP IPv4 201
- Assigning an IPv6 Address 204
- Displaying IP Addresses 206
- Modifying IP Addresses 207
- Modifying an 208
- IPv6 Address 208
- Setting LLDP and LLDP-MED 209
- Setting LLDP Locations 211
- Figure 74. Locations Tab 212
- 5. Click Add 214
- Creating a 215
- Coordinate 215
- Location 215
- Creating an 217
- ELIN Location 217
- Configuring LLDP and LLDP-MED 219
- Setting LLDP 220
- Port Assignments 220
- Assigning Port 222
- Locations 222
- Enabling LLDP 224
- Displaying LLDP 231
- Neighbor 231
- Information 231
- Neighbor Detail 232
- Displaying LLDP Statistics 236
- Displaying LLDP Locations 238
- Displaying 239
- Displaying ELIN 240
- Displaying the 241
- Basic LLDP 241
- Configuration 241
- Displaying Port 243
- LLDP-MED TLV 245
- Disabling LLDP on the Switch 247
- Setting sFlow 249
- Configuring sFlow on a Port 252
- Chapter 20: Setting sFlow 254
- Enabling sFlow on the Switch 256
- Displaying the sFlow Settings 257
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-9000 Series
(330 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern