Allied-telesis AT-9000 Series Bedienungsanleitung Seite 120
- Seite / 258
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 10: Setting Static Port Trunks
120
Modifying the Static Trunk Settings
Review the following information if you are adding ports to an existing
trunk:
If the port you are adding is the lowest numbered port in the trunk, its
parameter settings overwrites the settings of the existing ports in the
trunk. Therefore, check if its settings are appropriate before adding it
to the trunk. If the new port is not the lowest numbered port, its port
settings are changed to match the settings of the existing ports in the
trunk.
If the new port added to a trunk is already a member of another static
trunk, you must first remove it from its current trunk assignment.
To add or delete member ports from a static port trunk, do the following:
1. Hover the cursor over the Switching tab.
The Switching tab is displayed. See Figure 20 on page 59.
2. From the Switching tab, hover over Link Aggregation.
For an example of the Link Aggregation selection, see Figure 42 on
page 115.
3. Move the cursor to the right and select Static Trunks.
The Static Trunks page is displayed. See Figure 44 on page 116.
4. From the Static Trunks page, click Edit
.
The Modify Static Trunk page is displayed. See Figure 46 on page
121.
- AT-9000 Series 1
- Copyright 2
- Contents 5
- Document Conventions 12
- Contacting Allied Telesis 14
- Browser Interface 15
- Management Sessions 16
- Web Manager Accounts 17
- Starting a Management Session 19
- Figure 3. Login Page 22
- What to Configure First 27
- Saving Your Changes 28
- 5 on page 28 29
- Basic Switch Parameters 31
- Setting System 33
- Time Manually 33
- Setting an SNTP 34
- Setting a Remote Log Server 39
- Displaying and 42
- Setting the Active 42
- Uploading a 43
- Managing User Accounts 44
- Changing a User 45
- Password 45
- Changing the 47
- User Privilege 47
- Rebooting a Switch 49
- Upgrading the Software 50
- Displaying System Information 53
- Setting Port Parameters 57
- Changing the Port Settings 62
- 7. Click Apply 65
- 8. Click SAVE 65
- Setting Port Statistics 71
- Displaying Port Statistics 72
- Receive Statistics 73
- Transmit 75
- Statistics 75
- Interface 77
- Clearing Port Statistics 79
- Setting Port Mirroring 81
- Assigning a Destination Port 85
- Specifying Direction Type 86
- Chapter 7 89
- Setting the MAC Address 95
- Displaying the MAC Address 96
- Multicast MAC 97
- Addresses 97
- Assigning a MAC Address 98
- Multicast 99
- Deleting a MAC Address 101
- Setting LACP 103
- Overview 104
- Displaying LACP Trunks 105
- Chapter 9: Setting LACP 106
- Modifying an LACP Trunk 109
- Adding Static Trunks 117
- Deleting Static Trunks 123
- Chapter 11 125
- Tagged and 127
- Untagged Ports 127
- Displaying VLANs 128
- Adding a VLAN 130
- Modifying VLANs 132
- Assigning a Native VLAN 134
- 7. Click SAVE 135
- Deleting VLANs 136
- Protocol (IGMP) Snooping 137
- Clearing the Routers List 141
- 5. Click Apply 142
- 6. Click SAVE 142
- Disabling IGMP Snooping 143
- Displaying the Routers List 144
- Displaying the Hosts List 145
- Chapter 13 147
- Power Over Ethernet (PoE) 155
- Prioritization 157
- Displaying PoE Settings 158
- PoE Configuration 160
- Security 163
- Interface— Port number 166
- Chapter 16 171
- Server 1 174
- Configuring 175
- Remote Manager 175
- Authentication 175
- Using RADIUS 175
- Adding a 177
- RADIUS Server 177
- Using TACACS+ 179
- Chapter 17 185
- Chapter 18 197
- IP Management 199
- Guidelines 199
- Assigning an IPv4 Address 200
- Assigning a 201
- DHCP IPv4 201
- Assigning an IPv6 Address 204
- Displaying IP Addresses 206
- Modifying IP Addresses 207
- Modifying an 208
- IPv6 Address 208
- Setting LLDP and LLDP-MED 209
- Setting LLDP Locations 211
- Figure 74. Locations Tab 212
- 5. Click Add 214
- Creating a 215
- Coordinate 215
- Location 215
- Creating an 217
- ELIN Location 217
- Configuring LLDP and LLDP-MED 219
- Setting LLDP 220
- Port Assignments 220
- Assigning Port 222
- Locations 222
- Enabling LLDP 224
- Displaying LLDP 231
- Neighbor 231
- Information 231
- Neighbor Detail 232
- Displaying LLDP Statistics 236
- Displaying LLDP Locations 238
- Displaying 239
- Displaying ELIN 240
- Displaying the 241
- Basic LLDP 241
- Configuration 241
- Displaying Port 243
- LLDP-MED TLV 245
- Disabling LLDP on the Switch 247
- Setting sFlow 249
- Configuring sFlow on a Port 252
- Chapter 20: Setting sFlow 254
- Enabling sFlow on the Switch 256
- Displaying the sFlow Settings 257
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-9000 Series
(330 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern