Allied-telesis AT-S101 Bedienungsanleitung Seite 217
- Seite / 238
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AT-S101 Management Software User’s Guide
217
Downloading or Uploading a Configuration File via TFTP
This section describes how to download or upload a configuration file
using TFTP on an TFTP server. Before uploading or downloading a
configuration file onto the switch using TFTP, note the following:
The current configuration of a switch is retained when a new AT-S101
software image is installed. To return a switch to its default
configuration values, see “Returning the AT-S101 Management
Software to the Factory Default Values” on page 44.
Your network must have a node with TFTP server software.
You must store the new AT-S101 image file on the TFTP server.
Start the TFTP server software before you begin the download
procedure.
To download or upload an AT-S101 configuration file onto the switch using
a TFTP server, perform the following procedure:
1. From the menu on the left side of the home page, select the Tools
folder.
The Tools folder expands.
2. From the Tools folder, select the Config File Upload/Download
folder.
The Config File Upload/Download folder expands.
3. From the Config File Upload/Down folder, select via TFTP.
The Configuration Upload/Download via TFTP Page is displayed. See
Figure 69.
Figure 69. Configuration Upload/Download via TFTP Page
- User’s Guide 1
- Contents 3
- Document Conventions 10
- Contacting Allied Telesis 12
- Chapter 1 13
- Switch’s IP Address 14
- Save Configuration 17
- Web Browser Tools 18
- Basic Switch Parameters 21
- Setting Up the IP Access List 24
- Deleting an IP 26
- Adding System 31
- Administration 31
- Information 31
- Modifying 32
- Deleting 33
- Viewing System Information 36
- Rebooting a Switch 39
- Pinging a Remote System 41
- Average Time 43
- Virtual LANs 45
- VLAN Overview 46
- Tagged VLAN 48
- Tagged and Untagged Ports 49
- Port VLAN Identifier 49
- Chapter 3: Virtual LANs 50
- Creating a Tagged VLAN 51
- Modifying a Tagged VLAN 53
- Deleting a Tagged VLAN 55
- Creating a Port-Based VLAN 56
- Modifying a Port-Based VLAN 57
- Deleting a Port-Based VLAN 59
- Quality of Service (QoS) 61
- Configuring CoS 67
- Port Configuration 71
- Chapter 5: Port Configuration 74
- Port Trunking 77
- Port Trunking Overview 78
- Static Port Trunk Guidelines 79
- Creating a Port Trunk 80
- Modifying a Port Trunk 82
- 7. Click Apply 83
- Disabling a Port Trunk 84
- LACP Port Trunks 85
- LACP Overview 86
- Chapter 7: LACP Port Trunks 88
- LACP System Priority 90
- Key Parameter 90
- LACP Port Priority Value 90
- Displaying LACP Group Status 94
- Selecting Port Priority 96
- Chapter 8 99
- SNMP Overview 100
- Community String Attributes 101
- Creating an SNMP Community 104
- Modifying an SNMP Community 105
- Deleting an SNMP Community 106
- Creating a Host Table 107
- Modifying a Host Table Entry 108
- Deleting a Host Table Entry 109
- Enabling or Disabling Traps 110
- Modifying Traps 111
- Deleting Traps 112
- IGMP Snooping 113
- Overview 114
- Configuring IGMP Snooping 116
- Chapter 9: IGMP Snooping 118
- Bandwidth Control 119
- Setting Bandwidth Control 121
- Chapter 10: Bandwidth Control 122
- Port Mirroring 123
- Configuring Port Mirroring 125
- Disabling Port Mirroring 126
- Static Multicast MAC Address 127
- Protocols 133
- Path Costs and 136
- Port Costs 136
- Hello Time and 138
- Bridge Protocol 138
- Data Units 138
- Point-to-Point Ports 139
- (Full-duplex Mode) 139
- Edge Port 140
- Point-to-Point and Edge Port 141
- Workstation 141
- Mixed STP and RSTP Networks 142
- Spanning Tree and VLANs 143
- Configuring the 148
- Basic RSTP Port 148
- Settings 148
- Advanced RSTP 150
- Port Settings 150
- Chapter 14 157
- Authentication 159
- Authenticator 159
- AT-GS950/8POE 160
- Port-based 161
- Network Access 161
- Guidelines 161
- Switch A 163
- Switch B 163
- Guest VLANs 164
- Chapter 15 169
- Configuring the RADIUS Client 171
- Destination MAC Filter 173
- Power over Ethernet (PoE) 179
- Port Power Priority 181
- Setting Power over Ethernet 182
- Classifiers 185
- Classifier Criteria 187
- VLAN ID 188
- Protocol (Layer 2) 188
- DSCP (DiffServ Code Point) 189
- Protocol 189
- Creating Classifiers 192
- Chapter 18: Classifiers 194
- Access Control Policies 195
- ACP Components 197
- Creating Profile Action 199
- Creating an In-profile Action 201
- Creating a Policy 206
- Displaying a Policy Sequence 208
- Management Software Updates 209
- Statistics 219
- Chapter 21: Statistics 222
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-S101
(48 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern