Allied Telesis AT-TQ2403 Bedienungsanleitung Seite 162
- Seite / 292
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
162 AT-TQ2403 - Management Software - User's Guide
Figure 66: Security Setting Page – IEEE802.1x Setting Page
. . . then configure IEEE 802.1x security with certificate authentication on each client as follows.
- SAFETY NOTICE 3
- STANDARDS 4
- CONTENTS 6
- FIGURES 12
- Preface 15
- Contacting Allied Telesis 16
- Wireless Access Point 17
- Dynamic IP Addressing 19
- Static IP Addressing 19
- Recovering an IP Address 20
- Management Software 21
- Network 25
- Navigating to Basic Settings 27
- Provide Network Settings 29
- Update Basic Settings 30
- Navigation 30
- Clusters 31
- Understanding Clustering 32
- Which Are Not? 33
- Cluster Formation 34
- Cluster Size and Membership 34
- Intra-Cluster Security 35
- Setting the Cluster Name 36
- Viewing User Accounts 40
- Adding a User 40
- Editing a User Account 41
- Removing a User Account 42
- Sorting Session Information 45
- How it Works in a Nutshell 47
- Update Advanced Settings 51
- When to Use Static WEP 58
- When to Use IEEE 802.1x 59
- When to Use WPA Personal 60
- When to Use WPA Enterprise 60
- None (Plain-text) 64
- Static WEP 65
- Example of Using Static WEP 68
- IEEE 802.1x 69
- WPA Personal 71
- WPA Enterprise 73
- Interfaces 78
- Ethernet (Wired) Settings 79
- Wireless Settings 79
- Event Logs 79
- Severity 80
- Understanding Remote Logging 81
- Update Settings 82
- Transmit/Receive Statistics 83
- Associated Wireless Clients 84
- Neighboring Access Points 85
- Interface 88
- Setting the DNS HostName 89
- Deployment Example 102
- Networks 104
- Configuring VLANs 105
- Updating Settings 106
- Understanding Radio Settings 107
- Navigating to Radio Settings 107
- Enabled 109
- Disabled 109
- Address Filtering 114
- Chapter 17: Load Balancing 116
- Configuring Load Balancing 117
- Using Pre-Config Rogue AP 120
- Understanding QoS 121
- 802.1q and DSCP tags 125
- Navigating to QoS Settings 126
- Configuring QoS Queues 126
- Distribution System (WDS) 132
- Navigating to WDS Settings 134
- Configuring WDS Settings 135
- Understanding SNMP 138
- Supported MIBs 139
- Navigating to SNMP Settings 140
- Configuring SNMP Settings 140
- Configuring SNMP Traps 142
- Updating SNMP Settings 143
- Protocol Server 144
- Configuration 146
- Rebooting the Access Point 148
- Upgrading the Firmware 149
- Security Settings 153
- Security) 154
- Configuring a RADIUS server 183
- Appendix B: Troubleshooting 185
- BootLoader Recovery 186
- Telnet Connection to the AP 190
- SSH Connection to the AP 191
- Commands and Syntax 192
- Ready to Get Started? 197
- Saving Configuration Changes 198
- Basic Settings 199
- User Accounts 204
- Get All User Accounts 205
- Add Users 205
- Remove a User Account 206
- Get Status on Events 211
- Get Status on Persistence 211
- View Log Settings 212
- Specify the Relay Host 213
- Specify the Relay Port 214
- Get Client Associations 214
- Get Neighboring APs 215
- Ethernet (Wired) Interface 216
- Get the DNS Name 217
- Set the DNS Name 217
- To get the connection type: 218
- To view the new settings: 218
- Wireless Interface 220
- Guest Access 220
- View Guest Login Settings 222
- Set Guest Welcome Page Text 223
- Review Guest Login Settings 223
- Set the SSID for a VWN 224
- Enable or Disable a VWN 225
- Get the VLAN ID of a VWN 225
- Set the VLAN ID of a VWN 225
- Get the SSID of a VWN 226
- Example: Configuring VWNs 227
- Security 228
- Set Security to Plain Text 230
- Set Security to Static WEP 231
- Set Security to IEEE 802.1x 234
- Radio Settings 244
- Get IEEE 802.11 Radio Mode 245
- Get Radio Channel 246
- Get Basic Radio Settings 246
- Get All Radio Settings 246
- Get Supported Rate Set 247
- Get Basic Rate Set 247
- Configure Radio Settings 247
- MAC Filtering 253
- Load Balancing 255
- Quality of Service 256
- Get QoS Settings on the AP 258
- Set AIFS on the AP 259
- Configuring a WDS Link 262
- Time Protocol 265
- Pre-Config Rogue AP 266
- Reboot the AP 266
- Upgrade the Firmware 267
- Keyboard Shortcuts 268
- Tab Completion and Help 269
- Glossary 274
Verwandte Produkte und Handbücher für Software Allied Telesis AT-TQ2403
Software Allied Telesis AT-S94 Betriebsanweisung
(254 Seiten)
(254 Seiten)
Software Allied Telesis AT-S80 Betriebsanweisung
(242 Seiten)
(242 Seiten)
Software Allied Telesis AT-8000S Betriebsanweisung
(204 Seiten)
(204 Seiten)
Software Allied Telesis AT-S82 Betriebsanweisung
(76 Seiten)
(76 Seiten)
(49 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern