Allied-telesis AT-AR256E Bedienungsanleitung

Web Interface User Guide Allied Telesyn AT-AR256E 4-Port ADSL Router Rev. 1.0

- 10 - Figure 3 (Setup page) 4.3.1 Wide Area Network Connection On the other side of the ADSL router is where your Wide Area Network (WAN) connec

- 11 - Since multiple users can use the ADSL router, the ADSL router can simultaneously support multiple connection types; hence, the user must se

- 12 - To complete the connection, you must now click the Apply button. The Apply button will temporarily save this connection. To make the

- 13 - Figure 5 (PPPoA Connection Setup) To complete the connection, you must now click the Apply button. The Apply button will temporarily s

- 14 - e. Keep Alive: When on-demand option is not enabled, this value specifies the time to wait without being connected to your provider before

- 15 - using 0,100. Also select the Quality of Service (QoS); leave the default value if you are unsure or the ISP did not provide this informatio

- 16 - Based upon the information your ADSL Provider/ISP provided, enter your assigned IP address, Subnet Mask, Default Gateway (if provided), and

- 17 - Figure 9 (CLIP Connection Setup) To complete the connection, you must now click the Apply button. The Apply button will temporar

- 18 - 4.5.1 Enable/Disable DHCP To enable or disable DHCP, click setup. Under LAN Setup, select DHCP Configuration. This will bring up the pag

- 19 - Figure 11 (Example of a DHCP Relay configuration) By turning off the DHCP server and relay, the network administrator must carefully config

- 2 - 1. Introduction... 4 1.1 Main

- 20 - Figure 12 (Management IP) The Apply button will temporarily save this connection. To make the change permanent, you need to click on S

- 21 - To enable UPnP, you must first have a WAN connection configured. Once the WAN connection is configured, click Advanced and under Advanced,

- 22 - For example, if you want to host a NetMeeting session, from the Home page, click Advanced and under Advanced, select Port Forwarding. First

- 23 - Figure 14 (Access Control) The Apply button will temporarily save this connection. To make the change permanent, you need to click on S

- 24 - 4.6.3.4 Enable Incoming ICMP Ping Enabling the Incoming Internet Control Message Protocol (ICMP) Ping will allow Echo requests to come into

- 25 - the “Apply” button. The “Select All” select box can also be used to delete the entire filter rule. It provides a quick method of selecting

- 26 - b. There are no restrictions on a host's location. c. There are no restrictions on the number of members that may belong to a host gr

- 27 - Mask is 255.255.255.0. The Gateway IP address should be the IP address of the gateway device that allows for contact between the Gateway an

- 28 - in RIP v2 format using subnet broadcasting. If RIP v1 Compatible is selected, routing data will be sent in RIP v2 format using multicasting

- 29 - 4.7.2 User Management You can change the ADSL router’s username and password by clicking on User Management. From here you can change the

- 3 - 5.2 I Can’t Connect To The ADSL Router. ... 32 5.3 The DSL Link LED Continues To B

- 30 - 4.7.4 Ping Test Once you have the ADSL router configured, it is a good idea to make sure you can ping the network. You can get to the Pin

- 31 - 4.8.2 Connection Status Select to view the Status of different connections. 4.8.3 DHCP Clients Select to view the list of DHCP clients.

- 32 - 5. Appendix A: Troubleshooting Below is a list of commonly asked questions. Before calling technical support, please look through these is

- 33 - 5.4 The DSL Link LED Is Always Off 1. Make sure you have a ADSL service. You should get some kind of information from your ISP that state

- 34 - 6. ADSL Router Terms What Is A Firewall? A firewall is a protection between the Internet and your local network. It acts similarly to the

- 35 - or other network device where to send data if the target station does not reside on the same subnet as the source. If your machine can reac

- 4 - 1. Introduction The AT-AR256E 4-Port ADSL Router is the perfect high speed WAN bridge/router. This full-featured product is specifically d

- 5 - Management Support • Web Based HTTP management GUI • TFTP/FTP Support for Firmware Upgrade • Web Based Firmware Upgrade (Local) • Soft Fa

- 6 - 2. Your Gateway at a Glance The AT-AR256E 4-Port ADSL Router has several ports and LEDs. Let’s take a look at them. 2.1 Ports and Buttons

- 7 - 3. Installing Your ADSL Router 1. Locate an optimum location for the ADSL router. 2. For connections to the Ethernet and DSL interfaces, p

- 8 - 4. Setting Up Your ADSL Router This section will guide you through the ADSL router’s configuration. The ADSL router is shipped with a stand

- 9 - The Quick Start page is meant for basic users who only require easy and seamless connectivity to the Internet, without worrying about any oth