Allied-telesis AT-S62 Bedienungsanleitung Seite 171
- Seite / 573
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AT-S62 Command Line User’s Guide
171
SET SWITCH PORT RATELIMIT
Syntax
set switch port=all [rate=value]
[bcastratelimiting=yes|no|on|off|true|false|
enabled|disabled]
[mcastratelimiting=yes|no|on|off|true|false|
enabled|disabled]
[unkucastratelimiting=yes|no|on|off|true|false|
enabled|disabled]
Parameters
port Specifies all ports on the switch. This feature
cannot be configured on a per-port basis. You
must specify ALL.
rate Specifies the number of ingress packets the switch
ports accept each second. This setting applies all
packet types that have their rate limit enabled. The
range is 0 to 262,143.
bcastratelimiting Enables or disables rate limiting for ingress
broadcast packets. Settings for this parameter are:
yes, on, true, enabled Activates broadcast
packet rate limit on the
port. The values are
equivalent.
no, off, false, disabled Deactivates broadcast
packet rate limit on the
port. The values are
equivalent.
mcastratelimiting Enables or disables rate limiting for ingress
multicast packets. Settings for this parameter are:
yes, on, true, enabled Activates multicast
packet rate limit on the
port. The values are
equivalent.
no, off, false, disabled Deactivates multicast
packet rate limit on the
port. The values are
equivalent.
unkucastratelimiting Enables or disables rate limiting for unknown
ingress unicast packets. An unknown unicast
packet is a packet whose destination MAC
address is not stored in the switch’s MAC address
- Command Line 1
- User’s Guide 1
- Table of Contents 10
- Document Conventions 14
- Contacting Allied Telesyn 15
- Starting a Command Line 16
- Management Session 16
- Starting a Management Session 17
- Command Formatting 19
- Basic Command Line Commands 20
- CLEAR SCREEN 21
- LOGOFF, LOGOUT, and QUIT 24
- SAVE CONFIGURATION 26
- SET PROMPT 27
- SET SWITCH CONSOLEMODE 28
- SHOW USER 29
- Enhanced Stacking Commands 30
- ACCESS SWITCH 31
- SET SWITCH STACKMODE 33
- SHOW REMOTELIST 35
- Basic Switch Commands 36
- DISABLE DHCPBOOTP 38
- DISABLE IP REMOTEASSIGN 39
- ENABLE BOOTP 41
- ENABLE DHCP 42
- ENABLE IP REMOTEASSIGN 43
- ENABLE TELNET 44
- FORMAT DEVICE 45
- PURGE IP 48
- RESET SWITCH 49
- RESET SYSTEM 50
- RESTART REBOOT 51
- RESTART SWITCH 52
- SET ASYN 54
- SET IP INTERFACE 55
- SET IP ROUTE 57
- SET PASSWORD MANAGER 58
- SET PASSWORD OPERATOR 59
- SET SYSTEM 61
- SET USER PASSWORD 62
- SHOW ASYN 63
- SHOW CONFIG 64
- SHOW DHCPBOOTP 65
- SHOW IP INTERFACE 66
- SHOW SWITCH 68
- SHOW SYSTEM 69
- Simple Network Time Protocol 70
- (SNTP) Commands 70
- ADD SNTPSERVER PEER 71
- DISABLE SNTP 73
- ENABLE SNTP 74
- PURGE SNTP 75
- SET DATE TIME 76
- SET SNTP 77
- SHOW SNTP 78
- SHOW TIME 79
- ADD SNMP COMMUNITY 81
- CREATE SNMP COMMUNITY 83
- DELETE SNMP COMMUNITY 86
- DESTROY SNMP COMMUNITY 88
- DISABLE SNMP 89
- DISABLE SNMP AUTHENTICATETRAP 90
- DISABLE SNMP COMMUNITY 91
- ENABLE SNMP 92
- ENABLE SNMP AUTHENTICATETRAP 93
- ENABLE SNMP COMMUNITY 94
- SET SNMP COMMUNITY 95
- SHOW SNMP 97
- SNMPv3 Commands 99
- ADD SNMPV3 USER 101
- Chapter 7: SNMPv3 Commands 102
- CLEAR SNMPV3 NOTIFY 106
- CLEAR SNMPV3 TARGETADDR 107
- CLEAR SNMPV3 VIEW 108
- CREATE SNMPV3 ACCESS 109
- CREATE SNMPV3 COMMUNITY 112
- CREATE SNMPV3 GROUP 114
- CREATE SNMPV3 NOTIFY 116
- CREATE SNMPV3 TARGETADDR 118
- CREATE SNMPV3 TARGETPARAMS 120
- CREATE SNMPV3 VIEW 122
- DELETE SNMPV3 USER 124
- DESTROY SNMPv3 ACCESS 125
- DESTROY SNMPv3 GROUP 128
- DESTROY SNMPv3 NOTIFY 129
- DESTROY SNMPv3 TARGETADDR 130
- DESTROY SNMPv3 TARGETPARMS 131
- DESTROY SNMPV3 VIEW 132
- SET SNMPV3 ACCESS 133
- SHOW SNMPV3 COMMUNITY 150
- SHOW SNMPv3 GROUP 151
- SHOW SNMPV3 NOTIFY 152
- SHOW SNMPV3 TARGETADDR 153
- SHOW SNMPV3 TARGETPARAMS 154
- SHOW SNMPV3 USER 155
- SHOW SNMPV3 VIEW 156
- Port Parameter Commands 157
- ACTIVATE SWITCH PORT 158
- DISABLE INTERFACE LINKTRAP 159
- DISABLE SWITCH PORT 160
- DISABLE SWITCH PORT FLOW 161
- ENABLE INTERFACE LINKTRAP 162
- ENABLE SWITCH PORT 163
- ENABLE SWITCH PORT FLOW 164
- RESET SWITCH PORT 165
- SET SWITCH PORT 166
- SET SWITCH PORT RATELIMIT 171
- SHOW INTERFACE 174
- SHOW SWITCH PORT 176
- MAC Address Table Commands 177
- ADD SWITCH FDB 178
- DELETE SWITCH FDB 180
- RESET SWITCH FDB 181
- SHOW SWITCH FDB 184
- Port Trunking Commands 186
- ADD SWITCH TRUNK 187
- CREATE SWITCH TRUNK 188
- DELETE SWITCH TRUNK 190
- DESTROY SWITCH TRUNK 191
- SET SWITCH TRUNK 192
- SHOW SWITCH TRUNK 193
- Networking Stack Commands 194
- DELETE IP ARP 195
- DELETE TCP 196
- RESET IP ARP 197
- SET IP ARP 198
- SHOW IP ARP 199
- SHOW IP ROUTE 200
- SHOW TCP 201
- 169.254.37.1:23 202
- IP Address 202
- TCP Port 202
- LACP Commands 204
- ADD LACP PORT 205
- Chapter 12: LACP Commands 206
- DESTROY LACP AGGREGATOR 210
- DISABLE LACP 211
- ENABLE LACP 212
- SET LACP AGGREGATOR 213
- SET LACP PORT 214
- SET LACP PRIORITY 216
- SET LACP STATE 217
- SHOW LACP 218
- Port Mirroring Commands 219
- SET SWITCH MIRROR 220
- SET SWITCH PORT MIRROR 221
- SHOW SWITCH MIRROR 222
- Statistics Commands 223
- RESET SWITCH PORT COUNTER 224
- SHOW SWITCH COUNTER 225
- SHOW SWITCH PORT COUNTER 226
- File System Commands 227
- CREATE CONFIG 229
- DELETE FILE 230
- SET CONFIG 232
- SHOW FILE 234
- Commands 235
- File Download and Upload 235
- LOAD METHOD=LOCAL 236
- LOAD METHOD=TFTP 238
- LOAD METHOD=XMODEM 242
- UPLOAD METHOD=LOCAL 246
- UPLOAD METHOD=REMOTESWITCH 248
- UPLOAD METHOD=TFTP 253
- UPLOAD METHOD=XMODEM 256
- Event Log and Syslog Server 258
- ADD LOG OUTPUT 259
- CREATE LOG OUTPUT 262
- DESTROY LOG OUTPUT 266
- DISABLE LOG 267
- DISABLE LOG OUTPUT 268
- ENABLE LOG 269
- ENABLE LOG OUTPUT 270
- PURGE LOG 271
- SAVE LOG 272
- SET LOG FULLACTION 274
- SET LOG OUTPUT 275
- SHOW LOG 278
- SHOW LOG OUTPUT 283
- SHOW LOG STATUS 285
- Classifier Commands 286
- CREATE CLASSIFIER 287
- DESTROY CLASSIFIER 291
- PURGE CLASSIFIER 292
- SET CLASSIFIER 293
- SHOW CLASSIFIER 297
- ACL Commands 298
- CREATE ACL 299
- Chapter 19: ACL Commands 300
- PURGE ACL 302
- Quality of Service (QoS) 306
- ADD QOS FLOWGROUP 308
- ADD QOS POLICY 309
- ADD QOS TRAFFICCLASS 310
- CREATE QOS FLOWGROUP 311
- CREATE QOS POLICY 314
- CREATE QOS TRAFFICCLASS 320
- DELETE QOS FLOWGROUP 324
- DELETE QOS POLICY 325
- DELETE QOS TRAFFICCLASS 326
- DESTROY QOS FLOWGROUP 327
- DESTROY QOS POLICY 328
- DESTROY QOS TRAFFICCLASS 329
- SET QOS FLOWGROUP 330
- SET QOS POLICY 333
- SET QOS PORT 336
- SET QOS TRAFFICCLASS 337
- SHOW QOS FLOWGROUP 341
- SHOW QOS POLICY 342
- SHOW QOS TRAFFICCLASS 343
- Chapter 21 344
- MAP QOS COSP 345
- SET QOS COSP 347
- SET QOS SCHEDULING 348
- SHOW QOS CONFIG 349
- Power Over Ethernet Commands 350
- DISABLE POE PORT 351
- ENABLE POE PORT 352
- SET POE PORT 353
- SET POE THRESHOLD 355
- SHOW POE CONFIG 356
- SHOW POE STATUS 357
- IGMP Snooping Commands 359
- DISABLE IGMPSNOOPING 360
- ENABLE IGMPSNOOPING 361
- SET IP IGMP 362
- SHOW IGMPSNOOPING 364
- SHOW IP IGMP 365
- SET DOS IPOPTION 369
- SET DOS LAND 370
- SET DOS PINGOFDEATH 371
- SET DOS SMURF 373
- SET DOS SYNFLOOD 374
- SET DOS TEARDROP 375
- SHOW DOS 377
- STP Commands 379
- ACTIVATE STP 380
- DISABLE STP 381
- ENABLE STP 382
- PURGE STP 383
- Chapter 25: STP Commands 384
- RSTP Commands 392
- ACTIVATE RSTP 393
- DISABLE RSTP 394
- ENABLE RSTP 395
- PURGE RSTP 396
- SET RSTP 397
- Chapter 26: RSTP Commands 398
- SHOW RSTP 404
- MSTP Commands 406
- Protocol 407
- ACTIVATE MSTP 408
- ADD MSTP 409
- CREATE MSTP 410
- DELETE MSTP 411
- DESTROY MSTP MSTIID 412
- DISABLE MSTP 413
- ENABLE MSTP 414
- PURGE MSTP 415
- SET MSTP 416
- Chapter 27: MSTP Commands 418
- SET MSTP PORT 424
- VLANs and Multiple VLAN Mode 432
- ADD VLAN 433
- CREATE VLAN 435
- DELETE VLAN 439
- DESTROY VLAN 442
- SET SWITCH INFILTERING 443
- SET SWITCH MANAGEMENTVLAN 444
- SET SWITCH VLANMODE 445
- SET VLAN 447
- SHOW VLAN 448
- DISABLE GARP 450
- ENABLE GARP 451
- PURGE GARP 452
- SET GARP PORT 453
- SET GARP TIMER 454
- SHOW GARP 456
- SHOW GARP COUNTER 457
- SHOW GARP DATABASE 459
- SHOW GARP GIP 460
- SHOW GARP MACHINE 461
- Protected Ports VLAN Commands 462
- ADD VLAN GROUP 463
- CREATE VLAN PORTPROTECTED 466
- MAC Address Security 472
- SET SWITCH PORT SECURITYMODE 474
- SHOW SWITCH PORT INTRUSION 477
- SHOW SWITCH PORT SECURITYMODE 478
- DISABLE PORTACCESS 480
- DISABLE RADIUSACCOUNTING 481
- ENABLE PORTACCESS 482
- ENABLE RADIUSACCOUNTING 483
- SET RADIUSACCOUNTING 491
- SHOW PORTACCESS 493
- SHOW PORTACCESS 494
- SHOW RADIUSACCOUNTING 495
- Web Server Commands 496
- DISABLE HTTP SERVER 497
- ENABLE HTTP SERVER 498
- PURGE HTTP SERVER 499
- SET HTTP SERVER 500
- CERTIFICATE on page 516 503
- SERVER on page 497 503
- SHOW HTTP SERVER 506
- Encryption Key Commands 507
- CREATE ENCO KEY 508
- DESTROY ENCO KEY 512
- SET ENCO KEY 513
- SHOW ENCO 514
- Certificate Commands 515
- ADD PKI CERTIFICATE 516
- CREATE PKI CERTIFICATE 518
- CREATE PKI ENROLLMENTREQUEST 521
- DELETE PKI CERTIFICATE 523
- PURGE PKI 524
- SET PKI CERTIFICATE 525
- SET PKI CERTSTORELIMIT 527
- SET SYSTEM DISTINGUISHEDNAME 528
- SHOW PKI 529
- SHOW PKI CERTIFICATE 530
- Secure Sockets Layer (SSL) 531
- SHOW SSL 533
- Secure Shell (SSH) Commands 534
- DISABLE SSH SERVER 535
- ENABLE SSH SERVER 536
- SET SSH SERVER 539
- SHOW SSH 541
- TACACS+ and RADIUS 542
- ADD RADIUSSERVER 543
- ADD TACACSSERVER 545
- DELETE RADIUSSERVER 546
- DELETE TACACSSERVER 547
- DISABLE AUTHENTICATION 548
- ENABLE AUTHENTICATION 549
- PURGE AUTHENTICATION 550
- SET AUTHENTICATION 551
- SHOW AUTHENTICATION 553
- Management ACL Commands 554
- ADD MGMTACL 555
- DELETE MGMTACL 557
- DISABLE MGMTACL 558
- ENABLE MGMTACL 559
- SET MGMTACL 560
- SET MGMTACL STATE 562
- SHOW MGMTACL 563
Verwandte Produkte und Handbücher für Computerhardware Allied-telesis AT-S62
(12 Seiten)
(40 Seiten)
(38 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern