Allied-telesis AT-S39 Bedienungsanleitung

Management SoftwareAT-S39◆Command Line User’s GuideAT-8012M, AT-8016F/xx (SC or MT), AT-8024, AT-8024GB, AT-8024M, AT-8026FC, AT-8088/xx (SC or MT) FA

Section II: Local and Telnet Management10Contacting Allied TelesynTo contact Technical Support by phone, find your country or region in the table belo

Chapter 12: Rapid Spanning Tree Protocol Commands100SHOW RSTPSyntaxshow rstp [portconfig=ports|portstate=port]Parametersportconfig Displays the RSTP p

AT-S39 Command Line Interface User’s Guide101ACTIVATE RSTPSyntaxactivate rstpParametersNoneDescriptionUse this command to designate RSTP as the active

Chapter 12: Rapid Spanning Tree Protocol Commands102DISABLE RSTPSyntaxdisable rstpParametersNoneDescriptionThis command disables the Rapid Spanning Tr

AT-S39 Command Line Interface User’s Guide103ENABLE RSTPSyntaxenable rstpParametersNoneDescriptionThis command enables the Rapid Spanning Tree Protoco

Chapter 12: Rapid Spanning Tree Protocol Commands104RESET RSTPSyntaxreset rstpParametersNone.DescriptionThis command returns all bridge and port RSTP

AT-S39 Command Line Interface User’s Guide105SET RSTPSyntaxset rstp [default] [priority=priority] [hellotime=hellotime] [forwarddelay=forwarddelay] [m

Chapter 12: Rapid Spanning Tree Protocol Commands106hellotime Specifies the time interval between generating and sending configuration messages by the

AT-S39 Command Line Interface User’s Guide107❑ Maximum age time❑ Port priority❑ Force version of STP or normal RSTPExamplesThe following command retur

Chapter 12: Rapid Spanning Tree Protocol Commands108SET RSTP PORTSyntaxset rstp port=port|all [default] [portcost=portcost] [portpriority=portpriority

AT-S39 Command Line Interface User’s Guide109portpriority Specifies the port’s priority. This parameter is used as a tie breaker when two or more port

AT-S39 User’s Guide11Management Software UpdatesNew releases of management software for our managed products can be downloaded from our web site at ww

Chapter 12: Rapid Spanning Tree Protocol Commands110bridges connected to the port. If the port receives STP BPDU packets in response, the port changes

111Chapter 13VLAN Commands❑ SET SWITCH VLANMODE on page 113❑ SET SWITCH VLANSTATUS on page 127❑ SHOW VLAN on page 114❑ CREATE VLAN on page 115❑ ADD VL

Chapter 13: VLAN Commands112SET SWITCH SWITCHMODESyntaxset switch switchmode=tagged|basicParametersvlanmode Specifies the switch’s mode. Specifying ta

AT-S39 Command Line Interface User’s Guide113SET SWITCH VLANMODESyntaxset switch vlanmode=userconfig|multiple| dotqmultipleParametersvlanmode Specifie

Chapter 13: VLAN Commands114SHOW VLANSyntaxshow vlan=name|vidParametersvlan Specifies the name or VID of the VLAN.DescriptionThis command displays all

AT-S39 Command Line Interface User’s Guide115CREATE VLANNoteThis command is only allowed in user-configured VLANs mode. If you use this command when i

Chapter 13: VLAN Commands116VLAN on the switch.If this VLAN will be unique in your network, then its VID must also be unique. If this VLAN will be par

AT-S39 Command Line Interface User’s Guide117As shown at the start of this section, this command features two syntaxes. You can use either syntax when

Chapter 13: VLAN Commands118create vlan name=Sales vid=22 taggedports=3,6Now let’s try creating an tagged VLAN that contains both untagged and tagged

AT-S39 Command Line Interface User’s Guide119ADD VLANNoteThis command is only allowed in user-configured VLANs mode. If you use this command when in m

12Chapter 1Starting a Command Line Management SessionThis chapter contains the following sections:❑ Starting a Management Session on page 13❑ Key Feat

Chapter 13: VLAN Commands120mirrorport Specifies a port on the switch where all traffic on the VLAN will be mirrored. This function is useful in troub

AT-S39 Command Line Interface User’s Guide121add vlan name=production port=3 frame=taggedThe following command does the same thing using Syntax 2:add

Chapter 13: VLAN Commands122DELETE VLANNoteThis command is only allowed in user-configured VLANs mode. If you use this command when in multiple VLAN m

AT-S39 Command Line Interface User’s Guide123DescriptionThis command removes tagged and untagged ports from a VLAN. You can also use this command to c

Chapter 13: VLAN Commands124The following command does the same thing using Syntax 2:delete vlan name=production untaggedports=3To delete both tagged

AT-S39 Command Line Interface User’s Guide125DESTROY VLANNoteThis command is only allowed in user-configured VLANs mode. If you use this command when

Chapter 13: VLAN Commands126RESET VLANNoteThis command is only allowed in user-configured VLANs mode. If you use this command when in multiple VLAN mo

AT-S39 Command Line Interface User’s Guide127SET SWITCH VLANSTATUSSyntaxset switch vlanstatus=enabled|disabledParametersvlanstatus Specifies the switc

Chapter 13: VLAN Commands128SET SWITCH INFILTERINGSyntaxset switch infiltering=on|offParameterinfiltering Specifies the status of ingress filtering. O

129Chapter 14MAC Address Table Commands❑ SHOW SWITCH FDB on page 130❑ ADD SWITCH FDB on page 132❑ DELETE SWITCH FDB on page 133❑ SET SWITCH AGINGTIMER

AT-S39 Command Line User’s Guide13Starting a Management SessionIn order to manage an AT-8000 Series switch using the command line commands, you must f

Chapter 14: MAC Address Commands130SHOW SWITCH FDB Syntaxshow switch fdb [address=macaddress] [port=port] [status=static|dynamic|multicast] [vlan=name

AT-S39 Command Line Interface User’s Guide131The following command displays the port number on which the MAC address 00:A0:D2:18:1A:11 was learned (dy

Chapter 14: MAC Address Commands132ADD SWITCH FDBSyntaxadd switch fdb macaddress=macaddress port=portParametersmacaddress Specifies the static or mult

AT-S39 Command Line Interface User’s Guide133DELETE SWITCH FDBSyntaxdelete switch fdb macaddress=macaddress [vlan=name|VID]Parametersaddress Specifies

Chapter 14: MAC Address Commands134SET SWITCH AGINGTIMERSyntaxset switch agingtimer=valueParameteragingtimer Specifies the aging timer for the MAC add

135Chapter 15IGMP Snooping Commands❑ SET IP IGMP on page 136❑ SHOW IP IGMP on page 138NoteFor background information on IGMP snooping, refer to the AT

Chapter 15: IGMP Snooping Commands136SET IP IGMPSyntaxset ip igmp [snoopingstatus=enabled|disabled] [hoststatus=singlehost|multihost] [timeout=timeout

AT-S39 Command Line Interface User’s Guide137from filling up with multicast addresses, leaving no room for dynamic or static MAC addresses. The range

Chapter 15: IGMP Snooping Commands138SHOW IP IGMPSyntaxshow ip igmp [hostlist|routerlist]Parametershostlist Displays a list of the multicast groups le

139Chapter 16Broadcast Frame Control Command❑ SET SWITCH BROADCAST on page 140NoteRemember to save your changes with the SAVE CONFIGURATION command.No

Chapter 1: Starting a Command Line Management Session14Key FeaturesThe following features are supported in the command line interface:❑ Command histor

Chapter 16: Broadcast Frame Control Commands140SET SWITCH BROADCASTSyntaxset switch broadcast timer10_100mbps=integer timer1000mbps=integerParameterst

AT-S39 Command Line Interface User’s Guide141ExamplesThe following command sets a broadcast timer of 500 milliseconds for ports operating at 10 Mbps a

142Chapter 17TACACS+ and RADIUS Commands❑ DISABLE AUTHENTICATION on page 143❑ ENABLE AUTHENTICATION on page 144❑ RESET AUTHENTICATION on page 145❑ SET

AT-S39 Command Line Interface User’s Guide143DISABLE AUTHENTICATIONSyntaxdisable authenticationParametersNone.DescriptionUse this command to disable T

Chapter 17: TACACS+ and RADIUS Commands144ENABLE AUTHENTICATIONSyntaxenable authenticationParametersNone.DescriptionUse this parameter to enable TACAC

AT-S39 Command Line Interface User’s Guide145RESET AUTHENTICATIONSyntaxreset authenticationParameterNone.DescriptionThis command disables authenticati

Chapter 17: TACACS+ and RADIUS Commands146SET AUTHENTICATIONSyntaxset authentication method=[tacacs|radius] [secret=string] [timeout=integer]Parameter

AT-S39 Command Line Interface User’s Guide147The following command selects TACACS+ as the authentication protocol with a global encryption key of tige

Chapter 17: TACACS+ and RADIUS Commands148SHOW AUTHENTICATIONSyntaxshow authenticationParametersNone.DescriptionUse this command to display the follow

AT-S39 Command Line Interface User’s Guide149ADD TACACSSERVERSyntaxadd tacacsserver ipaddress=ipaddress order=integer [secret=string]Parametersipaddre

AT-S39 Command Line User’s Guide15Command FormattingThe following formatting conventions are used in this manual:❑ screen text font - This font is use

Chapter 17: TACACS+ and RADIUS Commands150DELETE TACACSSERVERSyntaxdelete tacacsserver ipaddress=ipaddressParametersipaddress Specifies the IP address

AT-S39 Command Line Interface User’s Guide151ADD RADIUSSERVERSyntaxadd radiusserver ipaddress=ipaddress order=integer [secret=string] [port=integer]Pa

Chapter 17: TACACS+ and RADIUS Commands152DELETE RADIUSSERVERSyntaxdelete radiusserver ipaddress=ipaddressParametersipaddress Specifies the IP address

153Chapter 18802.1x Port-Based Access Control Commands❑ ENABLE PORTACCESS on page 154❑ DISABLE PORTACCESS on page 155❑ SHOW PORTACCESS STATUS on page

Chapter 18: TACACS+ and RADIUS Commands154ENABLE PORTACCESSSyntaxenable portaccessParametersNone.DescriptionUse this command to enable port access con

AT-S39 Command Line Interface User’s Guide155DISABLE PORTACCESSSyntaxdisable portaccessParametersNone.DescriptionUse this command to disable port acce

Chapter 18: TACACS+ and RADIUS Commands156SHOW PORTACCESS STATUSSyntaxshow portaccess statusParametersNone.DescriptionUse this command to display the

AT-S39 Command Line Interface User’s Guide157SET PORTACCESSSyntaxset portaccess port=port|all[role=none|authenticator] [control=auto|forceauthenticate

Chapter 18: TACACS+ and RADIUS Commands158quietperiod Sets the number of seconds that the switch remains in the quiet state following a failed authent

AT-S39 Command Line Interface User’s Guide159set portaccess ports=all role=authenticatorTyping the following command, sets all ports with the role of

16Chapter 2Basic Command Line Commands❑ SAVE CONFIGURATION on page 17❑ SET PROMPT on page 18❑ CLEAR SCREEN on page 19❑ MENU on page 20❑ SET SWITCH CON

160Chapter 19Statistics Commands❑ SHOW SWITCH COUNTER on page 161❑ SHOW SWITCH PORT COUNTER on page 162❑ RESET SWITCH COUNTER on page 163❑ RESET SWITC

AT-S39 Command Line Interface User’s Guide161SHOW SWITCH COUNTERSyntaxshow switch counterParametersNone.DescriptionThis command displays switch operat

Chapter 19: Statistics Commands162SHOW SWITCH PORT COUNTERSyntaxshow switch port=port counterParametersport Specifies the port whose statistics you wa

AT-S39 Command Line Interface User’s Guide163RESET SWITCH COUNTERSyntaxreset switch counterParametersNone.DescriptionThis command returns all statisti

Chapter 19: Statistics Commands164RESET SWITCH PORT COUNTERSyntaxreset switch port=port|all counterParametersport Specifies the port whose statistics

165Chapter 20Download and Upload Commands❑ LOAD on page 166❑ UPLOAD on page 170❑ ENABLE TFTPSERVER on page 172❑ DISABLE TFTPSERVER on page 173❑ SHOW T

Chapter 20: Download and Upload Commands166LOADSyntaxload method=tftp|xmodem|remoteswitch type=image|config|bootloader switchnumber=switchesParameters

AT-S39 Command Line Interface User’s Guide167type Specifies the file to be downloaded. Options are:image Downloads both the AT-S39 software image and

Chapter 20: Download and Upload Commands168❑ A switch running AT-S39 Version 1.4 or earlier must first be ungraded to Version 1.4.1 or 1.4.2 before yo

AT-S39 Command Line Interface User’s Guide169The following command downloads a new AT-S39 configuration from the management workstation to the switch:

AT-S39 Command Line Interface User’s Guide17SAVE CONFIGURATIONSyntaxsave configurationParametersNone.DescriptionThis command saves your changes to the

Chapter 20: Download and Upload Commands170UPLOADSyntaxupload method=tftp|xmodem type=image|configmethod Specifies the method of the upload. Only one

AT-S39 Command Line Interface User’s Guide171ExamplesThe following command uploads the switch’s configuration file to the management workstation:uploa

Chapter 20: Download and Upload Commands172ENABLE TFTPSERVERSyntaxenable tftpserverParametersNone.DescriptionThis command activates the TFTP server so

AT-S39 Command Line Interface User’s Guide173DISABLE TFTPSERVERSyntaxdisable tftpserverParametersNone.DescriptionThis command disables the TFTP server

Chapter 20: Download and Upload Commands174SHOW TFTPSERVERSyntaxshow tftpserverParametersNone.DescriptionThis command displays the status of the TFTP

175Chapter 21Command Reference❑ Basic Command Line Commands on page 176❑ Basic Switch Commands on page 177❑ Enhanced Stacking Commands on page 179❑ SN

Chapter 21: Command Reference176Basic Command Line CommandsSAVE CONFIGURATIONsave configurationSaves your changes to the switch’s flash memory for per

AT-S39 Command Line Interface User’s Guide177Basic Switch CommandsSHOW IPshow ip interface=1Displays the IP address, subnet mask, and default gateway.

Chapter 21: Command Reference178SET SYSTEMset system [name=”name”] [contact=”contact”] [location=”location”]Sets a switch’s name, the name of the netw

AT-S39 Command Line Interface User’s Guide179SHOW CONFIGshow configDisplays overall information on the switch and the ports. PINGping ipaddressInstruc

Chapter 2: Basic Command Line Commands18SET PROMPTSyntaxset prompt=promptParameterPrompt Specifies the command line prompt. The prompt can be from one

Chapter 21: Command Reference180SNMP Community Strings and Trap CommandsSHOW SNMPshow snmpDisplays the community strings for SNMP Read and Write acces

AT-S39 Command Line Interface User’s Guide181Management Security CommandsSET PASSWORD MANAGERset password managerSets the manager’s password. SET PASS

Chapter 21: Command Reference182SET SWITCH CONSOLETIMERset switch consoletimer=valueSets the console timer.Port Parameter CommandsSHOW SWITCH PORTshow

AT-S39 Command Line Interface User’s Guide183Port Security CommandsSET SWITCH SECURITYMODEset switch securitymode=automatic|limited|secure|lockedSets

Chapter 21: Command Reference184DESTROY SWITCH TRUNKdestroy switch trunk=nameDeletes a port trunk from a switch. Port Mirroring CommandsCREATE SWITCH

AT-S39 Command Line Interface User’s Guide185Spanning Tree Protocol CommandsSHOW STPshow stp [port=port]Displays the STP parameter settings.ACTIVATE S

Chapter 21: Command Reference186Rapid Reconfiguration Spanning Tree CommandsSHOW RSTPshow rstp [portconfig=ports|portstate=port]Displays the RSTP para

AT-S39 Command Line Interface User’s Guide187VLAN CommandsSET SWITCH VLANMODE SET SWITCH VLANSTATUSSHOW VLANshow vlanDisplays all the VLANs on a switc

Chapter 21: Command Reference188Syntax 2delete vlan=name [vid=vid] taggedports=taggedports untaggedports=untaggedports [mirrorport=mirrorport]Removes

AT-S39 Command Line Interface User’s Guide189SET SWITCH INFILTERINGset switch infiltering=on|offActivates and deactivates ingress filtering.MAC Addres

AT-S39 Command Line Interface User’s Guide19CLEAR SCREENSyntaxclear screenParametersNone.DescriptionThis command clears the screen.ExampleThe followin

Chapter 21: Command Reference190SHOW IP IGMPshow ip igmp [hostlist|routerlist]Displays the IGMP parameter settings, host nodes, and multicast router p

AT-S39 Command Line Interface User’s Guide191ADD TACACSSERVERadd tacacsserver ipaddress=ipaddress order=integer [secret=string]Adds the IP address of

Chapter 21: Command Reference192SET PORTACCESSset portaccess port=port|all[role=none|authenticator] [control=auto|forceauthenticate|forceunauthenticat

AT-S39 Command Line Interface User’s Guide193Download a new version of the AT-S39 software image or a configuration file onto an AT-8000 Series switch

194IndexNumerics802.1x port-based accessDISABLE PORTACCESS, 155ENABLE PORTACCESS, 154SET PORTACCESS, 157SHOW PORTACCESS STATUS, 156802.1x port-based n

AT-S39 Command Line Interface User’s Guide195commandsACCESS SWITCH, 45ACTIVATE RSTP, 101ACTIVATE STP, 91ADD RADIUSSERVER, 151ADD SNMP COMMUNITY TRAPHO

Index196SHOW IP ROUTE, 30SHOW IP, 27SHOW PORTACCESS STATUS, 156SHOW REMOTELIST, 44SHOW RSTP, 100SHOW SNMP, 49SHOW STP, 90SHOW SWITCH COUNTER, 161SHOW

AT-S39 Command Line Interface User’s Guide197RRSTP commandsACTIVATE RSTP, 101DISABLE RSTP, 102ENABLE RSTP, 103RESET RSTP, 104SET RSTP PORT, 108SET RST

Copyright  2003 Allied Telesyn, Inc. 960 Stewart Drive Suite B, Sunnyvale, CA 94085 USAAll rights reserved. No part of this publication may be reprod

Chapter 2: Basic Command Line Commands20MENUSyntaxmenuParametersNone.DescriptionEntering this command at the command prompt displays the AT-S39 Main M

AT-S39 Command Line Interface User’s Guide21SET SWITCH CONSOLEMODESyntaxset switch consolemode=cli|menuParameterconsolemode Specifies the mode you wan

Chapter 2: Basic Command Line Commands22LOGOFF and QUITSyntaxlogoffquitParametersNone.DescriptionBoth commands perform the same function. They end a m

23Chapter 3Basic Switch Commands❑ SHOW DHCPBOOTP on page 24❑ ENABLE DHCPBOOTP on page 25❑ DISABLE DHCPBOOTP on page 26❑ SHOW IP on page 27❑ SET IP on

Chapter 3: Basic Switch Commands24SHOW DHCPBOOTPSyntaxshow dhcpbootpParametersNone.DescriptionThis command displays the status of DHCP and BOOTP on th

AT-S39 Command Line Interface User’s Guide25ENABLE DHCPBOOTPSyntaxenable dhcpbootpParametersNone.DescriptionThis command activates DHCP and BOOTP on t

Chapter 3: Basic Switch Commands26DISABLE DHCPBOOTPSyntaxdisable dhcpbootpParametersNone.DescriptionThis command deactivates DHCP and BOOTP on the swi

AT-S39 Command Line Interface User’s Guide27SHOW IPSyntaxshow ip interface=1Parametersinterface Specifies the interface number. This value is always “

Chapter 3: Basic Switch Commands28SET IPSyntaxset ip interface=1 ipaddress=IPaddress|DHCP netmask=subnetmaskParametersinterface Specifies the interfac

AT-S39 Command Line Interface User’s Guide29ExamplesThe following command sets a switch’s IP address to 140.35.22.22 and the subnet mask to 255.255.25

3Table of ContentsPreface ...

Chapter 3: Basic Switch Commands30SHOW IP ROUTESyntaxshow ip routeParametersNone.DescriptionThis command displays the switch’s default gateway address

AT-S39 Command Line Interface User’s Guide31SET IP ROUTESyntaxset ip route ipaddress=ipaddressParameteripaddress Specifies the IP address of the defau

Chapter 3: Basic Switch Commands32RESET IPSyntaxreset ip interface=1Parameterinterface Specifies the interface number. This value is always “1”. Descr

AT-S39 Command Line Interface User’s Guide33PURGE IPSyntaxpurge ip [ipaddress] [netmask] [route]Parametersipaddress Returns the switch’s IP address to

Chapter 3: Basic Switch Commands34SHOW SYSTEMSyntaxshow systemParametersNone.DescriptionThis command displays the following information:❑ Application

AT-S39 Command Line Interface User’s Guide35SET SYSTEMSyntaxset system [name=”name”] [contact=”contact”] [location=”location”]ParametersThe parameters

Chapter 3: Basic Switch Commands36RESET SYSTEMSyntaxreset system [name] [contact] [location]Parametersname Deletes the name of the switch.contact Dele

AT-S39 Command Line Interface User’s Guide37SHOW SWITCHSyntaxshow switchParametersNone.DescriptionThis command displays the following switch parameter

Chapter 3: Basic Switch Commands38RESTART SWITCHSyntaxrestart switchParameterNone.DescriptionThis command resets the switch. The system reset will tak

AT-S39 Command Line Interface User’s Guide39RESTART REBOOTSyntaxrestart rebootParametersNone.DescriptionThis command returns the switch’s operating pa

Table of Contents4RESTART REBOOT ...

Chapter 3: Basic Switch Commands40SHOW CONFIGSyntaxshow configParametersNone.DescriptionThis command displays overall information on the switch and th

AT-S39 Command Line Interface User’s Guide41PINGSyntaxping ipaddressParameteripaddress Specifies the IP address of an end node you want the switch to

42Chapter 4Enhanced Stacking Commands❑ SET SWITCH STACKMODE on page 43❑ SHOW REMOTELIST on page 44❑ ACCESS SWITCH on page 45❑ EXIT on page 47NoteRemem

AT-S39 Command Line Interface User’s Guide43SET SWITCH STACKMODESyntaxset switch stackmode=master|slave|unavailableParameterstackmode Specifies the en

Chapter 4: Enhanced Stacking Commands44SHOW REMOTELISTSyntaxshow remotelist [sorted by=macaddress|name]Parameterssorted by Sorts the list either by MA

AT-S39 Command Line Interface User’s Guide45ACCESS SWITCHSyntaxaccess switch number=number|macaddress=macaddressParametersnumber Specifies the number

Chapter 4: Enhanced Stacking Commands46The following command starts a management session on switch with the MAC address 00:30:84:52:02:11access switch

AT-S39 Command Line Interface User’s Guide47EXITSyntaxexitParametersNone.DescriptionEnds a management session. The menu or screen that is displayed as

48Chapter 5SNMP Community Strings and Trap Commands❑ SHOW SNMP on page 49❑ DESTROY SNMP COMMUNITY on page 50❑ CREATE SNMP COMMUNITY on page 51❑ SET SN

AT-S39 Command Line Interface User’s Guide49SHOW SNMPSyntaxshow snmpParametersNone.DescriptionThis command displays the community strings for SNMP Rea

5Chapter 10Port Mirroring Commands ...

Chapter 5: SNMP Community Strings and Trap Commands50DESTROY SNMP COMMUNITYSyntaxdestroy snmp community=communityParametercommunity Specifies the comm

AT-S39 Command Line Interface User’s Guide51CREATE SNMP COMMUNITYSyntaxcreate snmp community=community access=read|writeParametercommunity Specifies t

Chapter 5: SNMP Community Strings and Trap Commands52SET SNMP COMMUNITYSyntaxset snmp community=community access=read|writeParametercommunity Specifie

AT-S39 Command Line Interface User’s Guide53RESET SNMPSyntaxreset snmpParametersNone.DescriptionThis command performs the following functions:❑ Return

Chapter 5: SNMP Community Strings and Trap Commands54ADD SNMP COMMUNITY TRAPHOSTSyntaxadd snmp community=community traphost=ipaddressParameterscommuni

AT-S39 Command Line Interface User’s Guide55DELETE SNMP COMMUNITY TRAPHOSTSyntaxdelete snmp community=community traphost=ipaddressParameterscommunity

56Chapter 6Management Security Commands❑ SET PASSWORD MANAGER on page 57❑ SET PASSWORD OPERATOR on page 58❑ SHOW HTTP SERVER on page 59❑ ENABLE HTTP S

AT-S39 Command Line Interface User’s Guide57SET PASSWORD MANAGERSyntaxset password managerParametersNone.DescriptionThis command sets the manager’s pa

Chapter 6: Management Security Commands58SET PASSWORD OPERATORSyntaxset password operatorParametersNone.DescriptionThis command sets the operator’s pa

AT-S39 Command Line Interface User’s Guide59SHOW HTTP SERVERSyntaxshow http serverParametersNone.DescriptionThis command displays the status of the HT

Table of Contents6Chapter 17TACACS+ and RADIUS Commands ...

Chapter 6: Management Security Commands60ENABLE HTTP SERVERSyntaxenable http serverParametersNone.DescriptionThis command activates the HTTP server on

AT-S39 Command Line Interface User’s Guide61DISABLE HTTP SERVERSyntaxdisable http serverParametersNone.DescriptionThis command disables the HTTP serve

Chapter 6: Management Security Commands62ENABLE SNMPSyntaxenable snmpParametersNone.DescriptionThis command enables SNMP on the switch so that the dev

AT-S39 Command Line Interface User’s Guide63DISABLE SNMPSyntaxdisable snmpParametersNone.DescriptionThis command disables SNMP on the switch so that t

Chapter 6: Management Security Commands64SET SWITCH CONSOLETIMERSyntaxset switch consoletimer=valueParameterconsoletimer Specifies the console timer i

65Chapter 7Port Parameter Commands❑ SHOW SWITCH PORT on page 66❑ SET SWITCH PORT on page 67❑ RESET SWITCH PORT on page 71NoteRemember to save your cha

Chapter 7: Port Parameter Commands66SHOW SWITCH PORTSyntaxshow switch port=portParametersport Specifies the port whose parameter settings you want to

AT-S39 Command Line Interface User’s Guide67SET SWITCH PORTSyntaxset switch port=port|all [status=forwarding|disabled] [flowcontrol=none|transmit|reci

Chapter 7: Port Parameter Commands68information on broadcast frame control, refer to the AT-S39 User’s Guide. To set the broadcast timer interval, ref

AT-S39 Command Line Interface User’s Guide69100mfauto 100 Mbps and full-duplex mode with autonegotiation. 1000mfull 1000 Mbps and full-duplex mode.100

7PrefaceThis guide contains instructions on how configure an AT-8000 Series Fast Ethernet Switch using the AT-S39 command line interface. The Fast Eth

Chapter 7: Port Parameter Commands70ExamplesThe following command configures Port 11 to operate at 10 Mbps, half duplex:set switch port=11 speed=10mha

AT-S39 Command Line Interface User’s Guide71RESET SWITCH PORTSyntaxreset switch port=portParameterport Specifies the port to be reset. You can specify

72Chapter 8Port Security Commands❑ SET SWITCH SECURITYMODE on page 73❑ SET SWITCH THRESHOLD on page 75❑ SHOW SWITCH THRESHOLD on page 76NoteRemember t

AT-S39 Command Line Interface User’s Guide73SET SWITCH SECURITYMODESyntaxset switch securitymode=automatic|limited|secure|lockedParametersecuritymode

Chapter 8: Port Security Commands74DescriptionThis command sets a switch’s port security mode. Only one mode can be active on a switch at a time.NoteT

AT-S39 Command Line Interface User’s Guide75SET SWITCH THRESHOLDSyntaxset switch threshold=threshold port=port|allParametersthreshold Specifies the ma

Chapter 8: Port Security Commands76SHOW SWITCH THRESHOLDSyntaxshow switch thresholdParametersNone.DescriptionThis command displays the threshold limit

77Chapter 9Port Trunking Commands❑ SHOW SWITCH TRUNK on page 78❑ CREATE SWITCH TRUNK on page 79❑ ADD SWITCH TRUNK on page 80❑ DELETE SWITCH TRUNK on p

Chapter 9: Port Trunking Commands78SHOW SWITCH TRUNKSyntaxshow switch trunkParametersNone.DescriptionThis command displays the ports of a port trunk a

AT-S39 Command Line Interface User’s Guide79CREATE SWITCH TRUNKSyntaxcreate switch trunk=name port=ports [select=macsrc|macboth]Parameterstrunk Specif

Section II: Local and Telnet Management8Document ConventionsThis document uses the following conventions:NoteNotes provide additional information.Warn

Chapter 9: Port Trunking Commands80ADD SWITCH TRUNKSyntaxadd switch trunk=name port=portsParameterstrunk Specifies the name of the trunk to be modifie

AT-S39 Command Line Interface User’s Guide81DELETE SWITCH TRUNKSyntaxdelete switch trunk=name port=portsParameterstrunk Specifies the name of the trun

Chapter 9: Port Trunking Commands82DESTROY SWITCH TRUNKSyntaxdestroy switch trunk=nameParametertrunk Specifies the name of the trunk to be deleted. (Y

83Chapter 10Port Mirroring Commands❑ CREATE SWITCH MIRROR on page 84❑ ADD SWITCH MIRROR on page 85❑ DELETE SWITCH MIRROR on page 86❑ SET SWITCH MIRROR

Chapter 10: Port Mirroring Commands84CREATE SWITCH MIRRORSyntaxcreate switch mirror destport=destinationport srcport=sourceportParametersdestport Spe

AT-S39 Command Line Interface User’s Guide85ADD SWITCH MIRRORSyntaxadd switch mirror srcport=portParametersrcports Specifies the port(s) whose data ar

Chapter 10: Port Mirroring Commands86DELETE SWITCH MIRRORSyntaxdelete switch mirror srcport=portParameterssrcports Specifies the port(s) to be removed

AT-S39 Command Line Interface User’s Guide87SET SWITCH MIRRORSyntaxset switch mirror=portParametermirror Specifies the new destination port for the mi

Chapter 10: Port Mirroring Commands88DESTROY SWITCH MIRRORSyntaxdestroy switch mirrorParametersNone.DescriptionThis command deletes a port mirror. Onc

89Chapter 11STP Commands❑ SHOW STP on page 90❑ ACTIVATE STP on page 91❑ ENABLE STP on page 92❑ DISABLE STP on page 93❑ SET STP on page 94❑ SET STP POR

AT-S39 User’s Guide9Where to Find Web-based GuidesThe installation and user guides for all Allied Telesyn products are available in Portable Document

Chapter 11: Spanning Tree Protocol Commands90SHOW STPSyntaxshow stp [port=port]Parametersport Specifies the port whose STP parameters you want to view

AT-S39 Command Line Interface User’s Guide91ACTIVATE STPSyntaxactivate stpParametersNoneDescriptionUse this command to designate STP as the active spa

Chapter 11: Spanning Tree Protocol Commands92ENABLE STPSyntaxenable stpParametersNone.DescriptionThis command activates the Spanning Tree Protocol on

AT-S39 Command Line Interface User’s Guide93DISABLE STPSyntaxdisable stpParametersNone.DescriptionThis command deactivates the Spanning Tree Protocol

Chapter 11: Spanning Tree Protocol Commands94SET STPSyntaxset stp [default] [priority=priority] [hellotime=hellotime] [forwarddelay=forwarddelay] [max

AT-S39 Command Line Interface User’s Guide95NoteThe value for the maxage parameter must be less than (2 x (hellotime +1)) and less than (2 x (forwardd

Chapter 11: Spanning Tree Protocol Commands96SET STP PORTSyntaxset stp port=port|all [default] [portcost=portcost] [portpriority=portpriority] [fastmo

AT-S39 Command Line Interface User’s Guide97NoteA port that is not participating in spanning tree is immediately placed in the forwarding state. It ca

Chapter 11: Spanning Tree Protocol Commands98RESET STPSyntaxreset stpParametersNone.DescriptionThis command disables STP and returns all bridge and po

99Chapter 12RSTP Commands❑ SHOW RSTP on page 100❑ ACTIVATE RSTP on page 101❑ DISABLE RSTP on page 102❑ ENABLE RSTP on page 103❑ RESET RSTP on page 104