AlliedView™-EMS 3.8 (Full Installation) DEVICE MANAGEMENT GUIDE AlliedView™-EMS 3.8 DEVICE MANAGEMEN
Port Right clicking on a port opens a pull-down menu specific to the device. Selecting a menu item opens another window and lets yo
AT-9410GB This section describes Device Manager menus and operations specific to the AT-9410GB switch. Topics: • Main Window •
Note - When a port on the AT-9410GB is set to 'auto sense' and is connected to a half-duplex port on another device, its
Reset Resets the switch. Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server.
Alarm Table Displays the RMON Alarm table. Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Po
Note - Valid MIB Set values for the Port State parameter are 'enabled' and 'disabled'. Attempting to set this p
AT-FH800u Series This section describes Device Manager menus and operations specific to the AT-FH812u and AT-FH824u hubs. Topics
AT-FH824u Device Manager LEDs for AT-FH800u Series LED State Description PWR Green The hub is receiving power. Agent Men
Firmware Info Displays the version of the software running on the managed device. Manager Address Info Displays the management sta
RMON Menu From the RMON menu, you can view and edit RMON MIB. Statistics Displays traffic statistics in the network segment attac
Note - Valid MIB Set values for the Learn Action parameter are 'inactive' and 'active'. Attempting to set this
Module submenu Port selection dialog box When you select a menu item acting on ports, a dialog box opens to let you select ports.
AT-AR200E This section describes Device Manager menus and operations specific to the AT-AR240E, AT-AR250E, and AT-AR255E ADSL bri
AT-AR250E AT-AR255E Device Manager LEDs for ADSL Bridge/Router LED State Description PWR Green The router is receiving po
Note - The port speed displayed on the Ethernet port images is always '100' even if the Ethernet port is connected to a
Routing Menu From the Routing menu, you can view and edit information about the router's IP routing functions. ARP Table Displ
UDP Statistics Displays UDP statistics. TCP Statistics Displays TCP statistics. Note - The current firmware version does not
ATU Remote ATUR Physical Layer Inventory Displays the physical layer parameters of each remote ADSL transmission unit. ATUR Chan
ATM Menu From the ATM menu, you can view and edit ATM and AAL5-related information such as ATM interfaces, ATM virtual links, ATM c
• Parameter 5 • QoS Class • Status Attempting to configure these parameters will result in the error message: "The erro
Note - The Virtual Path (VP) Cross Connect sub-menu option does not display the correct parameters. Instead, it displays the sub-me
Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation
Select Port dialog box Port status colors Port status is shown by its color. Port speed is also displayed in the port image. •
Note - The current firmware version does not allow the following parameters to be configured: o Tinygram o Ring ID o Line ID
Security Secrets Displays information on the identities and secrets used by the PPP authentication protocols. Note -The current
Error Statistics Displays error statistics for the port. Note - The current firmware version returns 'noSuchName' for t
AT-AR300 Series This section describes Device Manager menus and operations specific to the AT-AR300 Series. Topics: • Main Windo
AT-AR300L(S) AT-AR320 AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 124 of 330
AT-AR350 AT-AR370(S) AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 125 of 330
AT-AR370(U) Device Manager LEDs for AT-AR300 Series LED State Description PWR Green The router is receiving power. B1 Green
File List Displays a list of the files in the router's flash file system. Config File Name Displays the file name of the
Frame Relay Menu From the Frame Relay menu you can view and edit Frame Relay information. The Frame Relay submenus are greyed out i
AT-AR400S Series This section describes Device Manager menus and operations specific to the AT-AR400S Series. Topics: • Main Win
AT-8000 Series This section describes Device Manager menus and operations specific to the AT-8000 Series. Topics: • Main Window
AT-AR440S AT-AR441S AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 130 of 330
AT-AR442S AT-AR450S Device Manager LEDs for AT-AR400S Series LED State Description PWR Green The router is receiving powe
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 132 of 330 Device Manager LEDs for AT-AR400S Series LED State Description Oran
Address Table Displays the list of IP interfaces and their IP addresses on the router. Route Table Displays the IP routing tabl
Attempting to configure these parameters will result in the error message: "The error occurred with 'Set' operation
Line Configuration Displays span configuration profiles for SHDSL lines. Alarm Configuration Displays alarm configuration profile
AT-AR410 This section describes Device Manager menus and operations specific to the AT-AR410 router. Topics: • Main Window • A
Agent Menu From the Agent menu, you can view and edit the system information for the router, or log into the CLI using Telnet. Syst
Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and spanning tree status
Port Menu From the Port menu, you can view and edit MIB information about selected ports. Interface Info Displays port statistics s
AT-8012M-QS AT-8016F/MT AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 14 of 330
AT-AR700 Series This section describes Device Manager menus and operations specific to the AT-AR700 Series. Topics: • Main Windo
AT-AR725 with PICs installed AT-AR725-DC AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 141 of 330
AT-AR740 AT-AR740-DC AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 142 of 330
AT-AR745 AT-AR745-DC AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 143 of 330
Device Manager LEDs for AT-AR700 Series LED State Description PWR Green Red The router is receiving power from the main power sup
Telnet Starts a Telnet connection to the router. WEB browser Opens your web browser and connects to the switch's HTTP server
Frame Relay Menu From the Frame Relay menu you can view and edit Frame Relay information. The Frame Relay submenus are greyed out i
AT-AR750S and AT-AR750S-DP This section describes Device Manager menus and operations specific to the AT-AR750S and AT-AR750S-DP r
AT-AR750S-DP Device Manager LEDs for AT-AR750S and AT-AR750S-DP LED State Description PWR Green The router is receiving po
Telnet Starts a Telnet connection to the router. WEB browser Opens your web browser and connects to the router's HTTP server
AT-8016F/SC AT-8016F/ST AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 15 of 330
Frame Relay Menu From the Frame Relay menu you can view and edit Frame Relay information. The Frame Relay submenus are unavailable
AT-8500 Series This section describes Device Manager menus and operations specific to the AT-8500 Series. Topics: • Main Window
AT-8524M AT-8524POE AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 152 of 330
AT-8550GB AT-8550SP Device Manager LEDs for AT-8500 Series LED State Description PWR Green The switch is receiving power.
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 154 of 330 Device Manager LEDs for AT-8500 Series LED State Description RPS Gr
Network Info Displays network-related information such as the addresses of the default gateway and the agents. Note - The current
Routing Menu From the Routing menu, you can view and edit information about the switch's routing functions. IP ARP Table Disp
Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree st
Event Log Displays the RMON Event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Utiliz
Note - AT-8550 : The current firmware version allows the Port Speed and Mode parameter of a GBIC or SFP port to be set to '10M
AT-8024 AT-8024GB AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 16 of 330
Note - The current firmware version accepts up to 32 characters for the Description parameter. NULL values are not allowed. Poli
Intrusion Attack Displays the VLAN ID and the MAC Address of each port. Note - The VLAN ID and MAC Address parameters do not retu
• The current firmware version allows the Port Speed and Mode parameter of the AT-A47 expansion module port to be set to '10M
AT-8700XL Series This section describes Device Manager menus and operations specific to the AT-8700XL Series of Advanced Layer 2
AT-8748XL Device Manager LEDs for AT-8700XL Series (AC Models) LED State Description PWR Green Red The switch is receiving po
Note - AT-8748XL and AT-8748XL-DC share the same device image. Note - Please refer to Uplink Modules for the operations and behavio
Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displ
Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilizati
AT-9400 Series This section describes Device Manager menus and operations specific to the AT-9400 Series. Topics: • Main Window
AT-9424T/GB AT-9424T/SP Device Manager LEDs for AT-9400 Series LED State Description PWR Green The switch is receiving po
AT-8024M AT-8026FC AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 17 of 330
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 170 of 330 Device Manager LEDs for AT-9400 Series LED State Description RPS Gr
Device Info Displays general information about the switch. Note - The current firmware version is unable to return a valid value
Note - The current firmware version does not allow the Default TTL parameter to be configured. UDP Listener Info Displays UDP li
Bridge Port Info Displays statistics about frames received/transmitted on the switch port. RMON Menu From the RMON menu you can v
Note - The current firmware version does not allow the Promiscuous Mode and Port Alias parameters to be configured. Additional I
Note - The Mirroring Source Module, Mirroring Source Port and Mirroring Destination Module parameters are not applicable to the AT-
AT-8600 Series This section describes Device Manager menus and operations specific to the AT-8600 Series Layer 3 Switch. Topics:
AT-8624T/2M AT-8648T/2SP Device Manager LEDs for AT-8600 Series LED State Description PWR Green Red The switch is receiving
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 178 of 330 Device Manager LEDs for AT-8600 Series LED State Description Red Gr
Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displ
AT-8026T AT-8088/MT AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 18 of 330
Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilizati
AT-8800 Series This section describes Device Manager menus and operations specific to the AT-8800 Series of Intelligent Workgroup
AT-8848 Device Manager LEDs for AT-8800 Series LED State Description PWR Green Red The switch is receiving power from the mai
Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. Syst
ARP Table Displays the ARP cache on the switch. Address Table Displays the list of IP interfaces on the switch. Route Table Dis
Spanning Tree Info Displays the port's spanning tree parameters. MAU Info Displays interface-related MAU information for t
AT-8948 and AT-8948i (AT-x900-48FE) This section describes Device Manager menus and operations specific to the AT-8948 and AT-894
AT-8948i (AT-x900-48FE) Device Manager LEDs for AT-8948 and AT-8948i (AT-x900-48FE) LED State Description PWR 1 and PWR 2 Gre
Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. Syst
Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displ
AT-8088/SC Device Manager LEDs for AT-8000 Series LED State Description PWR Green The switch is receiving power. MASTER Orange
Interface Info Displays port statistics such as the number of frames received and transmitted on the port, bytes received and tra
Rapier This section describes Device Manager menus and operations specific to Rapier Layer 3 Fast Ethernet Switches. Topics: •
Rapier 16F/SC Rapier 24 AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 192 of 330
Rapier 24i Rapier 48 AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 193 of 330
Rapier 48i Rapier G6 AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 194 of 330
Rapier G6F-LX/SC Rapier G6F-SX/SC AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 195 of 330
Rapier G6F-SX/MT Device Manager LEDs for Rapiers LED State Description PWR Green Red The switch is receiving power from the ma
Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. Syst
IP Statistics Displays statistics about IP routing, including the number of IP datagrams received. ICMP Statistics Displays sta
Call List Menu From the Call List menu, you can view ISDN call information. The Call List submenus are greyed out if the device is
TABLE OF CONTENTS BASIC OPERATIONS...
Note - Connection between an AT-8024GB and an AT-8324 can only be established if the uplink ports on both devices are configured to
SwitchBlade This section describes Device Manager menus and operations specific to the SwitchBlade Series, including the AT-SB421
Main Window SwitchBlade 4004 with SB4211 Switch Controller, SB4215 Bandwidth Expander, and Line Cards installed AlliedView™-EMS 3
SwitchBlade 4008 with SB4211 Switch Controller and Line Cards installed AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 202
Device Manager LEDs for AT-SB4211 Switch Controller LED State Description PWR Green The PSU is receiving power from its supply
Config File Name Displays the file name of the start-up configuration file. Boards Info Displays information about the chassis bo
Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either
SwitchBlade Line Cards This section describes the SwitchBlade Line Cards in Device Manager. If the following Line Cards are instal
LED State Description DUPLEX Green Orange The port is operating at full-duplex. The port is operating at half-duplex. AT-SB4441
8-Port (SC) 1000BASE-LX Gigabit Ethernet Line Card 8-Port (MT-RJ) 1000BASE-LX Gigabit Ethernet Line Card LED State Description
AT-9700 Series This section describes Device Manager menus and operations specific to the AT-9700 Series of Advanced Layer 3 Giga
MAC Address Table Displays a list of static MAC addresses configured on the switch. Note - MAC Address Table entries created thro
AT-9748TS/XP The AT-9748TS/XP supports up to 8 AT-9748TS/XP stacked switches with no uplinks or 5 AT-9748TS/XP stacked switches w
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 211 of 330 AT-9748TS/XP (With 10G Uplink) AT-9748TS/XP (No Uplink) AT-9724TS 2
Note - When multiple units of the AT-9700 series are stacked together, port numbering is continuous based on the Box ID. • Box ID
Unit Info Displays information about the system's stacking mode, units supported in the system, total number of ports and nu
IP Protocol Info Displays information about the IP interfaces supported by the system. Multiple Image List Displays information a
Note - The current firmware version does not allow the following parameters to be configured: o Repeating Start o Repeating End
Forwarding Database Displays the Forwarding Database table. ARP Aging Time Displays the timeout period in minutes for aging out d
Route Preferences Displays configurations of routing preferences. Route Redistribution Displays the route redistribution table
Note - The current firmware version does not allow the following parameters to be configured: o AS Border Router Status o Type
o Authentication Type o Authentication Key o Authentication Key ID o Row Status Interface Metric Displays the Type of Serv
Statistics Displays traffic statistics in the network segment attached to each port. History Control Table Displays the RMON Hist
Interface Info Displays a list of the device's multicast capable interfaces. Note - The current firmware version does not
Note - The current firmware version returns ‘noSuchName’ for the Join/Prune Interval parameter and does not allow it to be config
Component Displays the list of objects specific to a PIM. Note - The Component sub-menu option does not display the correct par
Scope Boundary Info Displays a list of the device's scoped multicast address boundaries. Note - The Scope Boundary Info sub
Note - If the MD5 Key parameter is set to a new value whose length is shorter than the length of the previously active MD5 Key, a
Overflow Counters Displays statistics for the high capacity interfaces of a transparent bridge. 802.1p Config Displays informat
Query Info Displays IGMP parameters such as the current IGMP query packets which is captured by this device, as well as the IGMP
Note - The current firmware version does not allow the Priority parameter to be configured when the Virtual IP Address (VRRP ->
Note - The current firmware version returns 'noSuchName' for the Port Number parameter. Authenticator PAE Diagnostics D
Note - The Authenticator PAE Diagnostics sub-menu option does not display the correct parameters. Instead, it displays the sub-me
• Expansion module ports • GBIC ports on the AT-8024GB • Fiber optic ports on the AT-8026FC • 10/100/1000Base-T ports on
Public Key Algorithm Displays the status of the RSA and DSA public key algorithms. Secure Socket Layer SSL Config Displays the st
Server Info Displays information about servers. Note - The current firmware version does not allow the Authentication Key paramet
Packet Content Info Displays ACL mask of user-defined information. Note - The current firmware version does not allow the followi
Note - The current firmware version returns 'noSuchName' for the Date and Time parameter. Network Interface Config Disp
Spanning Tree Info STP Displays information maintained by every port about the Spanning Tree Protocol. Note - The current firm
Displays QoS parameters and allows enabling of Hol prevention status and setting of scheduling mechanism. Scheduling Mechanism Di
Aggregator Port List Displays Link Aggregation Control information for every Aggregation Port associated with this device. Note -
AT-9800 Series This section describes Device Manager menus and operations specific to the AT-9800 Series of Multi-Layer Gigabit Sw
AT-9816GB Device Manager LEDs for AT-9800 Series LED State Description PWR Green Red The switch is receiving power from the ma
Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. Syst
new value to be converted to its equivalent wrap-around value; i.e., 65536 will become 0, 65537 will become 1, and so on. Note -
Routing Menu From the Routing menu, you can view and edit information about the switch's IP routing functions. ARP Table Displ
Utilization Displays the port's utilization information. Interface Info Displays port statistics such as the number of frame
AT-9924 Family This section describes Device Manager menus and operations specific to the AT-9924T, AT-9924SP and AT-9924T/4SP Ad
AT-9924SP AT-9924T/4SP Device Manager LEDs for AT-9924 Family LED State Description PWR 1 and PWR 2 Green Gray Red There i
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 244 of 330 Device Manager LEDs for AT-9924 Family LED State Description - a P
Telnet Starts a Telnet connection to the switch. WEB browser Opens your web browser and connects to the switch's HTTP serve
Statistics Displays statistics about frames received/transmitted on the switch port. Port Menu From the Port menu, you can view and
AT-9924Ts and AT-9924Tsi (AT-x900-24XT) This section describes Device Manager menus and operations specific to the AT-9924Ts and
AT-9924Tsi (AT-x900-24XT) Device Manager LEDs for AT-9924Ts and AT-9924Tsi (AT-x900-24XT) LED State Description PWR 1 and PWR
Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. Syst
• The Spanning Tree Protocol (STP) does not work for the AT-A46 expansion module when it is installed on an AT-8016F/ST device.
ARP Table Displays the ARP cache on the switch. Address Table Displays the list of IP interfaces on the switch. Route Table Dis
Spanning Tree Info Displays the port's spanning tree parameters. MAU Info Displays interface-related MAU information for t
AT-CV5000 This section describes Device Manager menus and operations specific to the AT-CV5000 chassis. Topics: • Main Window •
Device Manager LEDs for AT-CV5000 Chassis LED State Description PWR1 Green Gray Power supply 1 is installed and power is on. Powe
System Config Displays the device's systems variables. Diagnostics Displays the device's software version, fan speed and
Note - The current firmware version does not allow the correct module number to be displayed. As a result, the Module Number parame
Note - The current firmware version does not allow the Loopback Status parameter to be configured. AT-CV5000 AlliedView™-EMS 3.8
AT-CV5000 Modules This section describes the modules supported by Device Manager. If modules are installed on the AT-CV5000 chas
Note - To configure the Port Duplex Status parameter of the 100Base-FX port, the Port Mode parameter must first be set to 'ma
Note - The Port Mode parameter is not applicable to the AT-CV1KSS line card and should be ignored. Attempting to configure this par
AT-8000S Series This section describes Device Manager menus and operations specific to the AT-8000S Series. Topics: • Main Windo
AT-MCF06 Family This section describes Device Manager menus and operations specific to the AT-MCF06 family of media converters.
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 261 of 330 Device Manager LEDs for AT-MCF06 Family LED State Description NORM
Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Telnet Starts a Telnet connection to the media converter.
AT-MCF12 Family This section describes Device Manager menus and operations specific to the AT-MCF12 family of media converters.
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 264 of 330 Device Manager LEDs for AT-MCF12 Family LED State Description RPS G
Power Info Displays the status of the main and backup power supplies. Link Test Channel 1 to 6 Displays link test mode on channel
AT-MCF106 Family This section describes Device Manager menus and operations specific to the AT-MCF106 family of media converters.
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 267 of 330 Device Manager LEDs for AT-MCF106 Family LED State Description NORM
Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Telnet Starts a Telnet connection to the media converter. St
AT-MCF112 Family This section describes Device Manager menus and operations specific to the AT-MCF112 family of media converters.
AT-8000S/24, AT-8000S/48 and POE Models The AT-8000S/24, AT-8000S24/POE, AT 8000S/48 and AT-800S/48 POE can be joined together in
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 270 of 330 Device Manager LEDs for AT-MCF112 Family LED State Description NORM
Link Test Channel 1 to 6 Displays link test mode on channels 1 to 6. Link Test Channel 7 to 12 Displays link test mode on channel
AT-MPB3000 This section describes Device Manager menus and operations specific to the AT-MPB3000 chassis. Topics: • Main Window
Main Window AT-MPB3000 Note - The current firmware version does not allow Device Manager to support stacked AT-MPB3000 devices. De
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 274 of 330 Device Manager LEDs for AT-MMM-01 Management Module LED State Descr
Status Menu From the Status Menu, you can view information about AT-MPB3000 Modules installed on the chassis. Options to view all/p
AT-MPB3000 Modules This section describes the modules supported by Device Manager. If modules are installed on the AT-MPB3000 ch
Note - The MCM100-02 module image applies to the following variants: • AT-MCM100-02SC • AT-MCM100-02SMR • AT-MCM100-02SMRF15
AT-MCM1000S Modules MCM1000S LED State Description RAD Green The LX port is connected to a remote access device. Note - The TP
AT-MCM1000T Modules MCM1000T LED State Description RAD Green The LX port is connected to a remote access device. AT-MPB3000
Device Manager LEDs for AT-8000S Series LED State Description PWR Green The switch is receiving power. STACK ID Orange Gray
PowerBlade This section describes Device Manager menus and operations specific to the AT-PBC18 chassis. Topics: • Main Window •
Device Manager LEDs for AT-PBM02 Management Module LED State Description PWR Green Gray The main power supply is installed and po
Chassis Temperature Displays the actual temperature of the chassis. Power Info Displays power supply voltage information. Bat
PowerBlade Modules This section describes the modules supported by Device Manager. If modules are installed on the PowerBlade ch
AT-PB100 Series Media Converter Modules PB101 PB102 PB103/1 PB103/2 LED State Description DUP Green Gray The media c
AT-PB200 Series Switch Modules PB201 PB202 PB202/1 PB202/3 PB202/4 LED State Description DUP Green Gray The medi
AT-PB300 Series Media Converter Modules PB301 LED State Description DUP Green Gray The media converter is operating in full-d
AT-PB1000 Series Media Converter Modules PB1001/1 PB1001/3 PB1005G LED State Description LT Green Link Test is enable
AT-RG213 Family This section describes Device Manager menus and operations specific to the AT-RG213FX and AT-RG213TX Residential
Agent Menu From the Agent menu, you can view the system information for the device, or log into the CLI using Telnet. System Info D
Device Info General Info Displays common management information. Active Software File Displays the currently available images on t
Port Menu From the Port menu, you can view MIB information about the ethernet and voice ports. Interface Info Ethernet Displays in
Note - SIP : The current firmware version returns 'Not Available' for the Port Registration Time parameter. Note - SIP
AT-RG600 Series This section describes Device Manager menus and operations specific to the AT-RG600 Ethernet and ADSL Residential
AT-RG613LH AT-RG613SH AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 293 of 330
AT-RG613TX AT-RG634A AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 294 of 330
AT-RG644B AT-RG656BD Device Manager LEDs for AT-RG600 Series LED State Description PWR Green The residential gateway is rece
Note - If the user account used to connect to the AT-RG600 device is not the first user account defined in the Target Address table
accepted length will cause the device to restart and will eventually result in the error message: "The error occurred with &ap
Note - AT-RG656BD: Valid MIB Set values for the Password parameter are in the range [0-75] inclusive. Attempting to set this parame
Note - AT-RG656BD : Valid MIB Set values for the Aging Time Value parameter are in the range [0-2147483647] inclusive. However, the
EXPANSION MODULE NOTES ...
Software Packages Displays the device's software packages. Management Info General Management Displays common management inf
Server Info Displays a list of all multicast servers. Note - The Server Info sub-menu option does not display the correct paramete
Note - Valid MIB Set values for the Default Port parameter are in the range [1024-2147483647] inclusive. Attempting to set this par
Port Menu From the Port menu, you can view and edit MIB information about the ethernet and voice ports. Utilization Displays the po
Note - AT-RG600 ADSL: Attempting to configure the parameters under the Additional Info sub-menu option for LAN 4 will not result
Once the retrieval process is complete, the actual values for the different MIB variables will be shown. This applies to the follow
AT-WA7400 This section describes Device Manager menus and operations specific to the AT-WA7400 Dual Radio Wireless Access Point.
Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. Syst
Note - The current firmware version returns 'noSuchName' for the Re-assemble Max Size parameter. Route Table Display
Forwarding Database Displays the Forwarding Database table. Discard/Aging Time Info Displays information about the number of addr
Note - Configuring the Beacon Period parameter will result in the error message: "The error occurred with 'Set' oper
General Tuning Displays general tuning information. Note - The current firmware version accepts values in the range [0-255] inclusi
PHY Attributes Operation Displays PHY level attributes concerned with operation. Note - Valid MIB Set values for the Current Re
Peer STA Statistics Note - The Standard and Extended STA Statistics sub-menu options may, at times, not display the correct paramet
Note - The current firmware version returns 'noSuchName' for the following parameters: • Last Change Time and Date • Re
AT-WA750x Series This section describes Device Manager menus and operations specific to the AT-WA750x Series of Dual Radio Wirele
Agent Menu From the Agent menu, you can view and edit the system information for the switch, or log into the CLI using Telnet. Syst
Note - The current firmware version does not allow the Start Time parameter to be configured. DHCP Info Displays information for ad
ICMP Statistics Displays ICMP statistics. Bridge Menu From the Bridge menu, you can view bridge information such as the discard/a
Bridge State Displays status information about the bridge. ARP Basic Info Displays basic Address Resolution Protocol information.
Supplicant PAE Statistics Displays statistics objects for the Supplicant PAE associated with each port. Wi-Fi Menu From the Wi-Fi
Supported Transmit Data Rates Displays the Transmit bit rates supported by the PLCP and PMD. Note - AT-WA7501: The Supported Tran
Terminal Debug Mode Displays the terminal debug mode password. Note - The current firmware version does not allow the Terminal Debu
Error Statistics Displays error statistics for the ethernet port. Note - The Ethernet Chip Set parameter is not applicable to t
Port Interface Cards This section describes the Port Interface Cards supported in Device Manager. If one of these PICs is instal
AT-AR026 LED State Description DUPLEX Green The port is operating at full-duplex. Note - The four physical ports in this PIC a
Network Service Modules This section describes the Network Service Modules (NSMs) supported in Device Manager. If one of these NS
LED State Description "DATA" Orange Gray For permanent circuits, HDLC packets are being exchanged between the switch
Uplink Modules This section describes the Uplink Modules that can be installed on a switch. If one of these uplink modules is ins
AT-A16/AT-A17/AT-A19 Note - This image is only used on devices whose firmware does not allow Device Manager to differentiate the A
LED State Description DUPLEX Green Orange The port is operating at full-duplex. The port is operating at half-
AT-A60/AT-A60i (AT-XEM-1XP) Note - There are no LEDs on these modules. AT-A61/AT-A61i (AT-XEM-12S) Note - There are no
AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 329 of 330 LED State Description DUPLEX Green Orange The port is operating at
SNTP/NTP Client Config Displays information about SNTP/NTP client configuration. Note - Valid MIB Set values for the Polling Interv
USA Headquarters | 19800 North Creek Parkway | Suite 200 | Bothell | WA 98011 | USA | T: +1 800 424 4284 | F: +1 425 481 3895 European Headquarters |
Syslog Collector Displays the information to generate syslog messages to an aggregating agent or collector. Syslog Application Di
Note - The current firmware version does not allow the Routing Type parameter to be set to ‘local’ for all models except the AT-800
Route Table Displays the CIDR routing tables. Note - The current firmware version does not allow the following parameters to be co
Negative Cache Info Displays information about a collection of objects providing access to and control of a DNS resolver's neg
Note - The current firmware version does not allow the Number of Traffic Class parameter to be configured. 802.1p Device Capabiliti
Note - The current firmware version does not allow the EAP Current Method List parameter to be configured. Method Lists Displays in
AGENT MENU ...
Note - The current firmware version returns a 'noSuchName' value for the Port Number parameter. Note - The current firmwa
Note - The current firmware version is unable to display any value for the Client ID parameter. Authentication Server Info Displays
Secure Socket Layer Basic Info Displays basic SSL information. Note - The current firmware version does not allow the Certificate S
Note - The current firmware version does not allow Device Manager to display Utilization information. Interface Info Standard Displ
Note - The current firmware version is unable to display any value for the Port Number and Alignment Error Frames (HC) parameters.
Enable Enables the port. Disable Disables the port. Port Lock Basic Info Displays basic information about port lock. Interf
Tail Drop/WRED Displays information about the Tail Drop or WRED parameters and the EF of WRR parameters. Note - The current firmwar
Default VPT to Queue Displays information about the VLAN tag priority. Default DSCP to Queue Displays information about the setti
Status and Partner Operational Status parameters will also display unrecognizable values. Note - The current firmware version does
AT-8124 This section describes Device Manager menus and operations specific to the AT-8124 switch. Topics: • Main Window • Ag
ROUTING MENU ...
Agent Menu From the Agent menu, you can view and edit the system information for the device or log into the CLI using telnet. Syste
Statistics Displays statistics about frames received/transmitted on the switch port. RMON Menu From the RMON menu you can view
Detail Status Displays detailed port information such as duplex mode. Spanning Tree Info Displays the port's spanning tree
AT-8124XL (V2) This section describes Device Manager menus and operations specific to the AT-8124XL (V2) switch. Topics: • Main
Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. Syst
Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either the
Detail Info Displays detailed port information such as duplex mode. Note - Enabling/Disabling the Port STP Configuration parameter
Displays port mirroring parameters and allows configuration of port mirroring state, source, and destination. IGMP Snooping Displ
AT-8200XL Series This section describes Device Manager menus and operations specific to the AT-8216FXL/SC and AT-8224XL switches.
AT-8224XL Device Manager LEDs for AT-8200XL Series LED State Description PWR Green The switch is receiving power. RPS Green
ROUTING MENU ...
Note - The current firmware version allows the user to enter up to 64 characters for the System Contact and the System Location par
Diagnostics Displays the operating status of the switch's components such as power supply and system fans. Note - The current
Discard/Aging Time Info Displays information about the number of address entries that were learned but discarded because either the
Error Statistics Displays error statistics. Detail Info Displays detailed port information such as duplex mode. Note - The Port Fl
Expansion Module Notes • When the Port Speed and Mode parameter of an AT-A14 expansion module port is set to 'auto sense&apos
AT-8324 This section describes Device Manager menus and operations specific to the AT-8324 switch. Topics: • Main Window • Ag
Main Window AT-8324 Supports up to 8 stacked AT-8324 switches. Device Manager LEDs for AT-8324 LED State Description PWR Gre
Note - The current firmware version does not allow Device Manager to support the RPS and MASTER LEDs. Note - When a port is configu
Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree st
Event Table Displays the RMON Event table. Event Log Displays the RMON Event log. Port Menu From the Port menu, you can vie
AT-MCF106 FAMILY ...
These parameters are defined in v2.13 but will return 'noSuchName.' because they do not exist in v1.0. Note - The curr
• The Port Speed and Mode parameter of the 1000Base-X port on the AT-A15 expansion module can only be set to '1Gbps full-dupl
AT-8324SX This section describes Device Manager menus and operations specific to the AT-8324SX switch. Topics: • Main Window •
Main Window AT-8324SX Supports up to 4 stacked switches. AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 73 of 330
Device Manager LEDs for AT-8324SX LED State Description PWR Green The switch is receiving power. RPS Green Gray Redundant power
Telnet Starts a Telnet connection to the switch. WEB Browser Connects to the switch's HTTP server. Bridge Menu From the
Event Log Displays the RMON event log. Port Menu From the Port menu, you can view and edit MIB information about the port. Note -
Spanning Tree Info Displays the port's spanning tree parameters. Enable Enables the port. Disable Disables the port. Port
AT-8300GB Series This section describes Device Manager menus and operations specific to the AT-8300GB Series. Topics: • Main Wi
Main Window AT-8326GB The AT-8326GB supports up to 6 AT-8326GB stacked switches or any of the following mixed stack combinations
MAIN WINDOW ...
Note - When 3 or more AT-8326GB devices are stacked together, expect the twisted pair port image of Port 26 on the last device on t
Note - The current firmware version does not allow Device Manager to detect the presence or absence of a GBIC module in any of the
Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree st
Port Menu From the Port menu, you can view and edit MIB information about the port. Utilization Displays the port's utilizati
QoS Displays QoS parameters and allows enabling of QoS status and setting priority queue. Port Mirroring Displays port mirroring
AT-8400 This section describes Device Manager menus and operations specific to the AT-8400 switch. Topics: • Main Window • Ag
Device Manager LEDs for AT-8401 Management Module LED State Description FAN A Green Gray FAN TRAY A is installed and is operati
Agent Menu From the Agent menu, you can view and edit the system information for the device, or log into the CLI using Telnet. Sy
Bridge Menu From the Bridge menu, you can view and edit bridge information such as the forwarding database and the spanning tree st
Note - The current firmware version does not support the "historyControlTable" MIB object of RFC1757. As a result, Device
Basic Operations Device Manager's main window shows the main panel of the target device. It has both common and device-speci
Spanning Tree Info Displays the port's spanning tree parameters. Note - The current firmware version does not allow the Port
AT-8400 Line Cards This section describes the AT-8400 Line Cards supported by Device Manager. If line cards are installed on the
AT-8412 AT-8412/MT AT-8412/SC LED State Description DUPLEX Green The port is operating in full-duplex. Note - The curren
AT-8413 AT-8413GB/T LED State Description DUPLEX Green Orange The port is operating in full-duplex. The port is operating in
AT-8414 AT-8414/SC AT-8414/ST LED State Description DUPLEX Green Orange The port is operating in full-duplex. The port is
AT-9006 Family This section describes Device Manager menus and operations specific to the AT-9006SX/SC and AT-9006T switches. Top
AT-9006T Device Manager LEDs for AT-9006 Family LED State Description PWR Green The switch is receiving power. RPS Green Gr
Network Info Displays network-related information such as agent's and default gateway address. Manager Address Info Displa
Event Table Displays RMON Event table. Event Log Displays RMON Event log. VLAN Menu From the VLAN menu, you can view the list
Disable Disables the port. AT-9006 Family AlliedView™-EMS 3.8 DEVICE MANAGEMENT GUIDE Page 99 of 330
Kommentare zu diesen Handbüchern