AT-8400 ChassisAT-8400◆Installation Guide®PN 613-50395-00 Rev B
PrefacexContacting Allied TelesynThis section provides Allied Telesyn contact information for technical support as well as sales or corporate informat
AT-8400 Chassis Installation GuidexiObtaining Management Software UpdatesNew releases of management software for our managed products can be downloade
Prefacexii
1Chapter 1AT-8400 Series Switch OverviewThis chapter contains the following sections: Overview on page 2 Hardware Features on page 3 Software Featu
AT-8400 Series Switch Overview2OverviewThe AT-8400 Series switch is a modular unit that simplifies the task of building and maintaining a Fast Etherne
AT-8400 Chassis Installation Guide3Hardware FeaturesHardware features of the AT-8400 Series switch include: 13 slots — 12 slots for line cards, such
AT-8400 Series Switch Overview4 Internet Group Management Protocol (IGMP) snooping (RFC 2236) — controls the flow of multicast packets for improved n
AT-8400 Chassis Installation Guide5Front and Back Panel ComponentsFigure 2 illustrates the front panel of the chassis.Figure 2 Front Panel of the AT-
AT-8400 Series Switch Overview6Figure 4 illustrates the back panel of the DC model of the AT-8400 Series switch.Figure 4 Rear Panel of the AT-8400 Se
7Chapter 2Installing the AT-8400 ChassisThis chapter contains the following sections:❑ Overview on page 8❑ Installing the Chassis on a Desktop on page
Copyright 2003 Allied Telesyn, Inc. 960 Stewart Drive Suite B, Sunnyvale, CA 94085 USAAll rights reserved. No part of this publication may be reprod
Installing the AT-8400 Chassis8OverviewThis chapter discusses how to install the AT-8400 chassis on a desktop or in a rack and the necessary preparati
AT-8400 Chassis Installation Guide9VerifyingPackageContentsMake sure the following items are included in your package. If items are missing or damaged
Installing the AT-8400 Chassis10Preparing theSiteBe sure to observe the following guidelines when planning the installation of your chassis.❑ Make sur
AT-8400 Chassis Installation Guide11CautionPower cord is used as a disconnection device: To de-energize equipment, disconnect the power cord. 10 War
Installing the AT-8400 Chassis12Installing the Chassis on a DesktopThis section explains how to install the chassis on a desktop. To install the chass
AT-8400 Chassis Installation Guide13Installing the Chassis in a RackThe chassis can be installed in a 19-inch rack. Allied Telesyn recommends that you
Installing the AT-8400 Chassis142. Attach the brackets to the sides of the chassis with four screws (not provided) on each side.There are two ways to
AT-8400 Chassis Installation Guide153. Attach the chassis to the rack with two screws (not provided) on each side. Refer to Figure 9 on page 15.NoteTh
Installing the AT-8400 Chassis16Cabling and Powering on the ChassisThe following subsections describe how to cable and power on the AT-8400 chassis. F
AT-8400 Chassis Installation Guide17Connecting the Frame GroundTo ensure the safe and proper operation of your AT-8400 chassis, you must ground the un
iiiElectrical Safety and Emission Compliance StatementStandards: This product meets the following standards:RFI Emission FCC Class A, EN55022 Class A,
Installing the AT-8400 Chassis18To attach the frame ground, perform the following procedure:1. Use a crimping tool to affix the cable lug to one end o
AT-8400 Chassis Installation Guide19Powering on an AC ChassisThis procedure describes how to power on an AC powered AT-8400 chassis with an AT-PWR10 p
Installing the AT-8400 Chassis20Powering on a DC ChassisThis procedure describes how to power on a DC AT-8400 chassis. If your chassis is AC powered,
AT-8400 Chassis Installation Guide213. With a 14-gauge wire-stripping tool, strip the three wires in the tray cable coming from the DC input power sou
Installing the AT-8400 Chassis22WarningSafety Hazard - Check to see if there are any exposed copper strands coming from the installed wires. When this
23Chapter 3Installing and Removing Line CardsThis chapter contains the following sections:❑ Overview on page 24❑ Installing a Line Card on page 25❑ Re
Installing and Removing Line Cards24OverviewThis chapter contains general instructions for installing and removing line cards from the AT-8400 chassis
AT-8400 Chassis Installation Guide25Installing a Line CardThis section explains how to install a line card into the AT-8400 chassis. It is a generic p
Installing and Removing Line Cards26CautionIf the WAIT/REMOVE LED is steady amber, you must wait approxi-mately 20 seconds until it turns steady green
AT-8400 Chassis Installation Guide273. Using a Phillips screwdriver, loosen the two installation screws on the faceplate. See Figure 15.Figure 15 Rem
Installing and Removing Line Cards28NoteKeep the shipping material. You must use the original shipping material if you need to return the chassis to A
AT-8400 Chassis Installation Guide29NoteAlways use installation screws to secure the line card to the chassis. Leaving a line card partially seated ma
Installing and Removing Line Cards30Removing a Line CardThis section explains how to remove a line card from the AT-8400 chassis. It is a generic proc
AT-8400 Chassis Installation Guide31CautionIf the WAIT/REMOVE LED is steady amber, you must wait approxi-mately 20 seconds until it turns steady green
Installing and Removing Line Cards324. Using a Phillips screwdriver, loosen the two installation screws on the faceplate of the line card. See Figure
AT-8400 Chassis Installation Guide33Software Implications of Replacing Line CardsThe AT-S60 software allows you to remove and replace, or hotswap, lin
Installing and Removing Line Cards34When you remove a line card and do not replace it, the information you configured for the line card is saved on th
AT-8400 Chassis Installation Guide35For AT-8413 port trunk, all ports that are included in the trunk must belong to different line cards. As a result,
Installing and Removing Line Cards36
37Appendix ATechnical SpecificationsOverviewThis section lists the technical specifications of an AT-8400 Chassis that contains the following installe
vTable of ContentsPreface ...
Technical Specifications38Storage Humidity 5% to 95% (non-condensing)Altitude Up to 3,048 m (10,000 ft.)Power RequirementsInput Supply Voltages:AT-PWR
AT-8400 Chassis Installation Guide39Appendix BTranslated Safety InformationImportant: This appendix contains multiple-language translations for the sa
Translated Safety Information40Standards: This product meets the following standards. 1 RFI Emission FCC Class A, EN55022 Class A, EN61000-3-2, EN61
AT-8400 Chassis Installation Guide41 13 Caution: Air vents must not be blocked and must have free access to the room ambient air for cooling. 14 Ope
Translated Safety Information42 10 Vorsicht: DAS NETZKABEL DIENT ZUM TRENNEN DER STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DER STECKDOSE ZIEH
AT-8400 Chassis Installation Guide43Sikkerhed 6Advarsel: Laserprodukt av klasse 1. 7Advarsel: Stirr ikke på strålen. 8 Elektriske ForholdsreglerAdv
Translated Safety Information44Eisen: Dit product voldoet aan de volgende eisen. 1 RFI Emissie FCC Klasse A, EN55022 Klasse A, EN61000-3-2,EN61000-3
AT-8400 Chassis Installation Guide45 17 Waarschuwing: Verwijder niet meer dan de aanbevolen hoeveelheid isolatiemateriaal. Als u meer dan de aanbevol
Translated Safety Information46 13 Attention: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de circuler librement pour le refr
AT-8400 Chassis Installation Guide47 10 Huomautus: Virtajohtoa käytetään virrankatkaisulaitteena. Virta katkaistaan irrottamalla virtajohto. 11 SÄH
Table of ContentsviSoftware Implications of Replacing Line Cards ...
Translated Safety Information48 8 Avvertenze ElettricheAttenzione: PERICOLO DI SCOSSE ELETTRICHEPer evitare SCOSSE ELETTRICHE non asportare il coperc
AT-8400 Chassis Installation Guide49 3 Immunitet EN55024 4 Elektrisk sikkerhet EN60950 (TUV), UL60950 (UL/cUL) 5 Laser EN60825Sikkerhet 6Advarsel
Translated Safety Information50 20 Merknad: Systemet fungerer med positivt og negativt jordede likestrømssystemer.Padrões: Este produto atende aos s
AT-8400 Chassis Installation Guide51Ligue SEMPRE os cabos ao equipamento LAN primeiro antes de os ligar ao disjuntor. Para evitar o perigo de feriment
Translated Safety Information52 13 ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener acceso libre al aire ambiental de
AT-8400 Chassis Installation Guide53 9 Fara För BlixtnedslagFara: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER. 10 Varning: NÄTKABELN ANVÄN
Translated Safety Information54
AT-8400 Chassis Installation Guide55
Translated Safety Information56
viiPrefaceThis installation guide contains a description of the AT-8400 Series switch as well as instructions on how to install an AT-8400 chassis and
PrefaceviiiWhere to Find Related GuidesThe Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent documenta
AT-8400 Chassis Installation GuideixDocument ConventionsThis guide uses the following conventions: NoteNotes provide additional information.WarningWar
Kommentare zu diesen Handbüchern