613-000974 Rev. BAT-8000GS SeriesStackable Gigabit Ethernet SwitchesAT-8000GS/24AT-8000GS/POEAT-8000GS/48Installation Guide
Chapter 1: Overview10AT-8000GS Switch Series FeaturesThe AT-8000GS/24, AT-8000GS/24POE, and AT-8000GS/48 features include the following: Wire speed s
AT-8000GS Series Gigabit Ethernet Switch Installation Guide11IEEE Standards IEEE 802.3 — 10Base-T IEEE 802.3u — 100Base-TX IEEE 802.3ab — 1000Base-
Chapter 1: Overview12Model DescriptionsAT-8000GS/24 The following figure illustrates the AT-8000GS/24 front panel.Figure 1 AT-8000GS/24 Gigabit Ether
AT-8000GS Series Gigabit Ethernet Switch Installation Guide13AT-8000GS/24POEThe following figure illustrates the AT-8000GS/24POE front panel.Figure 3
Chapter 1: Overview14AT-8000GS/48 The following figure illustrates the AT-8000GS/48 front panel.Figure 5 AT-8000GS/48 Gigabit Ethernet Switch Front P
AT-8000GS Series Gigabit Ethernet Switch Installation Guide15Port Descriptions10/100/1000 Base-T GigabitEthernet PortsThe 10/100/1000Base-T Gigabit po
Chapter 1: Overview16LED DefinitionsThe switch has Light Emitting Diodes (LED) on both the front and rear panels that indicate the both the port statu
AT-8000GS Series Gigabit Ethernet Switch Installation Guide17Power LEDThe PWR LED on the front panel of the device indicates the power supply status.T
Chapter 1: Overview18The stacking LED indications are described in the following table:Mode LEDs You can select a particular status mode for a RJ-45 P
AT-8000GS Series Gigabit Ethernet Switch Installation Guide19Figure 9 below illustrates the mode LEDs on the front panel and Table 5 below gives the f
Copyright © 2008 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied
Chapter 1: Overview20Figure 10 RJ-45 Port LEDs for the AT-8000/24 and AT-8000/48Each non-POE RJ-45 port has two LEDs, one for Link and one for Mode s
AT-8000GS Series Gigabit Ethernet Switch Installation Guide21RJ-45 Port LEDsAT-8000GS/24POEFigure 11 on page 21 illustrates the 10/100/1000 Base-T RJ-
Chapter 1: Overview22SFP Port LEDs The following figure illustrates the SFP port LEDs.Figure 12 SFP Port LEDsThe SFP ports have one LEDs for link and
AT-8000GS Series Gigabit Ethernet Switch Installation Guide23Stacking PortLEDsThe Stacking LEDs are located on the rear panel. The following figure il
Chapter 1: Overview24
25Chapter 2InstallationThis chapter contains information for installing the device, and includes the following sections:“Reviewing Safety Precautions
Chapter 2: Installation26Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the chassis or any of
AT-8000GS Series Gigabit Ethernet Switch Installation Guide27Warning: Operating Temperature. This product is designed for a maximum ambient temperatur
Chapter 2: Installation28Warning: To reduce the risk of electric shock, the ports on this product must not connect to cabling that is routed outside t
AT-8000GS Series Gigabit Ethernet Switch Installation Guide29Preparing for InstallationThis section provides an explanation for preparing the installa
AT-8000GS Series Gigabit Ethernet Switch Installation Guide3PrefaceThis guide provides the hardware installation instructions for your managed, AT-800
Chapter 2: Installation30SiteRequirementsThe device should be placed on a table-top. Before installing the unit, verify that the location chosen for i
AT-8000GS Series Gigabit Ethernet Switch Installation Guide31To unpack the device perform the following:1. It is recommended to put on an ESD wrist st
Chapter 2: Installation32Installing the DeviceThe device can be installed on a flat surface or mounted in a rack. This section includes the following
AT-8000GS Series Gigabit Ethernet Switch Installation Guide33• Disconnect all cables from the unit before mounting the device in a rack or cabinet.• W
Chapter 2: Installation34Connecting the DeviceThis section describes how to connect the device, and includes the following sections:“Connecting the S
35Chapter 3StackingThis section describes the stacking control management and includes the following topics: “Stacking Overview” on page 36 “Configu
Chapter 3: Stacking36Stacking OverviewStacking provides multiple switch management through a single point as if all stack members are a single unit. A
AT-8000GS Series Gigabit Ethernet Switch Installation Guide37automatically switches to a Stacking Failover topology without any system downtime. An SN
Chapter 3: Stacking38manually configured as the Stacking Master, the manually configured member is elected Stacking Master.If two Master-enabled units
AT-8000GS Series Gigabit Ethernet Switch Installation Guide39 Units are reassigned Unit IDs Units toggle between Stacking mode and Stand-alone modeE
Preface4Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Description
Chapter 3: Stacking40Configuring StackingConfiguring stacking is performed during the bootup process. To configure a device as part of a stack, the bo
AT-8000GS Series Gigabit Ethernet Switch Installation Guide41The Startup Menu is displayed and contains the following configuration functions:6. From
Chapter 3: Stacking42
43Chapter 4Initial ConfigurationThis chapter contains information for installing the device, and includes the following sections:“Configuration Overv
Chapter 4: Initial Configuration44Configuration OverviewBefore assigning a static IP address to the device, obtain the following information from the
AT-8000GS Series Gigabit Ethernet Switch Installation Guide45ConfigurationThe initial configuration, which starts after the device has booted successf
Chapter 4: Initial Configuration46illustrated in the following example.User Name A user name is used to manage the device remotely, for example throug
47Chapter 5TroubleshootingThis chapter contains information on how to troubleshoot the switch in the event that a problem occurs.NoteIf you are still
Chapter 5: Troubleshooting48 Be sure the management station has an IP address in the same subnet as the switch’s IP interface to which it is connecte
49Appendix ATechnical SpecificationsPhysical SpecificationsThe different devices have the following physical specifications:AT-AT-8000/24 — 440 x 257
AT-8000GS Series Gigabit Ethernet Switch Installation Guide5Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis prod
Appendix A: Technical Specifications50Power SpecificationsPower Supply for Non-POE model100-240VAC/50-60 Hz universal inputTotal Power Consumption AT
AT-9400 Series Gigabit Ethernet Switches Installation Guide51Pin Connections for the 10/100/1000 Ethernet InterfaceThe following figure illustrates th
Appendix A: Technical Specifications52
Preface6Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales or corporate informa
7ContentPreface ...
Contents8Chapter 3: Stacking .........
9Chapter 1OverviewThis chapter contains the following sections: “AT-8000GS Switch Series Features” on page 10 “IEEE Standards” on page 11 “Model De
Kommentare zu diesen Handbüchern