Media Converter ChassisAT-MCR1Installation Guide613-000687 Rev B
Preface10Contacting Allied TelesisThis section provides Allied Telesis contact information for technical support as well as sales or corporate informa
AT-MCR1 Media Converter Chassis Installation Guide11tab.Sales or Corporate InformationYou can contact Allied Telesis for sales or corporate informatio
Preface12
13Chapter 1OverviewThe AT-MCR1, shown in Figure 1, is a chassis with an internal power supply designed to house one Allied Telesis media converter. Th
Chapter 1: Overview14Key FeaturesThe AT-MCR1 chassis has the following features: LED for unit status One slot for an ATI standard media converter I
15Chapter 2InstallationThis chapter contains the following sections: “Reviewing Safety Precautions” on page 16 “Verifying the Package Contents” on p
Chapter 2: Installation16Reviewing Safety PrecautionsReview the following safety precautions before you begin to install the AT-MCR1 chassis.NoteThe
AT-MCR1 Media Converter Chassis Installation Guide17Caution: Air vents must not be blocked and must have free access to the room ambient air for cooli
Chapter 2: Installation18Warning: Check to see if there are any exposed copper strands coming from the installed wires. When this installation is done
AT-MCR1 Media Converter Chassis Installation Guide19Warning: Reliable earthing of rack-mounted equipment should be maintained. Particular attention sh
Copyright © 2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied
Chapter 2: Installation20Verifying the Package ContentsMake sure the following items are included in your package. If any item is missing or damaged,
AT-MCR1 Media Converter Chassis Installation Guide21Selecting a SiteBe sure to observe the following requirements when choosing a site for your chassi
Chapter 2: Installation22Installing a Media Converter in the ChassisTo install a media converter in the AT-MCR1 chassis, perform the following procedu
AT-MCR1 Media Converter Chassis Installation Guide233. Align the mounting rail with the media converter, placing the two pins into the front and rear
Chapter 2: Installation245. Press gently on the media converter to seat the power plug into the chassis.6. Tighten the captive screw on the mounting r
AT-MCR1 Media Converter Chassis Installation Guide25Installing the Chassis On a Table or Desktop (AC Models Only)To install the chassis on a table or
Chapter 2: Installation26Installing the Chassis Under a Table (AC Models Only)The AT-MCR1 chassis can be mounted under a table using the mounting brac
AT-MCR1 Media Converter Chassis Installation Guide273. Attach one mounting bracket (provided) to each side of the chassis using the bracket mounting s
Chapter 2: Installation285. Make sure that the chassis is securely mounted under the table.6. Power the chassis on following the instructions in “Powe
AT-MCR1 Media Converter Chassis Installation Guide29Mounting the Chassis on the WallThe chassis can be mounted vertically on a wall using the mounting
3Electrical Safety and Emission Compliance StatementStandards: This product meets the following standards.U.S. Federal Communications CommissionDeclar
Chapter 2: Installation303. Turn the chassis over and attach a mounting bracket (provided) to each side of the chassis using the bracket mounting scre
AT-MCR1 Media Converter Chassis Installation Guide315. Make sure that the chassis is securely mounted onto the wall.6. Install the cables. For cabling
Chapter 2: Installation32Installing the Chassis in a RackYou can mount the chassis in an industry-standard 19” or 23” rack.To install the chassis in a
AT-MCR1 Media Converter Chassis Installation Guide333. Mount the AT-MCR1 chassis on a 19” or 23” rack using the rackmounting screws (not provided), as
Chapter 2: Installation34Powering On an AC-Powered ChassisTo apply power to an AC-powered AT-MCR1 chassis, perform the following procedure:1. Install
AT-MCR1 Media Converter Chassis Installation Guide353. Plug the power cord into the power connector on the back of the chassis, as shown in Figure 16.
Chapter 2: Installation366. Verify that the PWR LED in the front of the chassis is green. If the PWR LED is OFF, refer to Chapter 3, ”Troubleshooting”
AT-MCR1 Media Converter Chassis Installation Guide37Wiring and Powering On a DC-Powered ChassisTo wire and power on a DC-powered chassis, perform the
Chapter 2: Installation38A tray cable is required to connect the power source if the chassis is powered by centralized DC power. The tray cable must b
AT-MCR1 Media Converter Chassis Installation Guide39WarningDo not strip more than the recommended amount of wire. Stripping more than the recommended
4RFI Emissions FCC Part 15 Class BImmunity EN55024Electrical Safety EN60950 (TUV),UL 60950-1 (cULus),CSA C22.2Translated Safety StatementsImportant: T
Chapter 2: Installation405. Connect the negative feed wire to the terminal block marked (-).WarningCheck to see if there are any exposed copper strand
AT-MCR1 Media Converter Chassis Installation Guide41For cabling instructions, refer to the installation guide that is shipped with the Allied Telesis
Chapter 2: Installation42Warranty RegistrationWhen you have finished installing the product, register your product by completing the enclosed warranty
43Chapter 3TroubleshootingFollow the guidelines below to test and troubleshoot the installation in the event a problem occurs.If the PWR LED is OFF, d
Chapter 3: Troubleshooting44
45Appendix ATechnical SpecificationsPhysicalDimensions: W x D x H130 mm x 166 mm x 44 mm(5.118 in x 6.535 in x 1.732 in)Weight: .27 kg (0.60 lbs)Tempe
Appendix A: Technical Specifications46Safety and Electromagnetic Emissions CertificationsRFI Emissions FCC Part 15 Class BImmunity EN55024Electrical S
5Preface ...7Safety Symbols Used in this Document ...
Contents6Temperature ...45Electrical Rating (for AC version only)...
7PrefaceThis guide contains instructions on how to install an AT-MCR1 Media Converter Chassis. This preface contains the following sections: “Safety
Preface8Safety Symbols Used in this DocumentThis document uses the safety symbols in Table 1. Table 1. Safety SymbolsSymbol Meaning DescriptionCaution
AT-MCR1 Media Converter Chassis Installation Guide9Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are
Kommentare zu diesen Handbüchern