Allied Telesis AT-S94 Betriebsanweisung Seite 233
- Seite / 254
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Managing Stacking
Stacking Overview
Page 233
Chapter 18.Managing Stacking
This section describes the stacking control management and includes the following topics:
• Stacking Overview
• Configuring Stacking Management
Stacking Overview
Stacking provides multiple switch management through a single point as if all stack members are a single unit. All
stack members are accessed through a single IP address through which the stack is managed. The stack can be
managed using the following interfaces:
• Web-based Interface
• SNMP Management Station
• Command Line Interface (CLI)
Devices support stacking up to six units per stack, or can operate as stand-alone units. During the Stacking setup,
one switch is selected as the Stacking Master and another stacking member can be selected as the Secondary
Master. All other devices are selected as stack members, and assigned a unique Unit ID.
Switch software is downloaded for each stack member. During a software download, the software version is
downloaded to the master unit and can then be copied to all units at once. All units in the stack must be running
the same software version.
Switch stacking and configuration is maintained by the Stacking Master. The Stacking Master detects and
reconfigures the ports with minimal operational impact in the event of:
• Unit Failure
• Inter-unit Stacking Link Failure
• Unit Insertion
• Removing a Stacking Unit
This section includes the following topics:
• Stacking Ring Topology
• Stacking Chain Topology
• Stacking Members and Unit ID
• Removing and Replacing Stacking Members
• Exchanging Stacking Members
Stacking Ring Topology
Stacked devices operate in a Ring topology. A Ring topology is where all devices in the stack are connected to
each other forming a circle. Each stacked device accepts data and sends it to the device to which it is physically
connected. The packet continues through the stack until it reaches the destination port. The system automatically
discovers the optimal path on which to send traffic.
Most difficulties in Ring topologies occur when a device in the ring becomes non-functional, or a link is severed. In
a stack, the system automatically switches to a Stacking Failover topology without any system downtime. An
SNMP message is automatically generated, but no stack management action is required. However, the stacking
link or stacking member must be repaired to ensure the stacking integrity.
- User’s Guide 1
- Table of Contents 3
- • Intended Audience 8
- Intended Audience 9
- Document Conventions 10
- Contacting Allied Telesis 11
- Chapter 1. Getting Started 13
- Getting Started 15
- Figure 3: Port Settings Page 15
- User Interface Components 16
- Using the Management Buttons 17
- Figure 5: Add Community Page 19
- Saving Configurations 20
- Logging Out 21
- Resetting the Device 21
- Configurable Login Banner 21
- Defining System Information 23
- Figure 8: System General Page 23
- Chapter 3. Configuring IPv6 25
- Configuring Tunnels 31
- Defining IPv6 Neighbors 32
- Setting the System Clock 37
- Configuring SNTP 38
- Defining Access Profiles 43
- Defining Profile Rules 47
- Configuring Device Security 53
- Configuring TACACS+ 56
- Figure 28: Add TACACS+ Page 58
- Configuring RADIUS 60
- Figure 31: Add RADIUS Page 62
- Configuring Local Users 64
- Configuring Network Security 66
- Managing Port Security 67
- Figure 37: Port Security Page 68
- Defining 802.1x Port Access 70
- Enabling Storm Control 75
- Defining Access Control 77
- Adding ACE Rules 80
- Defining IPv4 Based ACL 81
- Defining IPv6 Based ACL 87
- Defining ACL Binding 91
- Configuring DHCP Snooping 93
- • Defining Trusted Interfaces 93
- Defining Trusted Interfaces 96
- Page 100 100
- Chapter 7. Configuring Ports 101
- Page 102 102
- Page 103 103
- Page 104 104
- Configuring Port Mirroring 105
- Page 106 106
- Aggregating Ports 107
- Defining Trunk Settings 108
- Page 109 109
- Page 110 110
- Defining Port Trunking 111
- Page 112 112
- Configuring LACP 113
- Allied Telesis 114
- Defining MAC Addresses 115
- Page 116 116
- Configuring Interfaces 117
- Configuring VLANs 118
- Defining VLAN Properties 119
- Page 120 120
- Figure 76: VLAN Configuration 121
- Page 122 122
- Page 123 123
- Defining GVRP 124
- Page 125 125
- Defining MAC Based Groups 126
- Page 127 127
- Page 128 128
- Defining Log Settings 129
- Adding Log Servers 130
- Page 131 131
- Modifying Log Servers 132
- Page 133 133
- Page 135 135
- Defining STP Properties 136
- Page 137 137
- Defining STP Interfaces 138
- Page 139 139
- Page 140 140
- Page 141 141
- Page 142 142
- Defining MSTP Properties 143
- Defining MSTP Interfaces 144
- Configuring Spanning Tree 145
- Page 146 146
- Page 149 149
- • Configuring IGMP Snooping 151
- Configuring IGMP Snooping 152
- Page 153 153
- Page 154 154
- Page 155 155
- Page 157 157
- Page 159 159
- Chapter 12.Configuring SNMP 161
- Enabling SNMP 162
- Defining SNMP Communities 163
- Page 164 164
- Page 165 165
- Defining SNMP Groups 167
- Page 168 168
- Configuring SNMP 169
- Defining SNMP Users 170
- Page 171 171
- Defining SNMP Views 173
- Figure 120:Add SNMP VIew Page 174
- Page 175 175
- SNMPv3 Notification Recipient 176
- Page 177 177
- Defining Notification Filters 179
- Page 180 180
- Chapter 13.Configuring LLDP 181
- Page 182 182
- Defining LLDP Port Settings 183
- Page 184 184
- Page 185 185
- Page 186 186
- Configuring LLDP 187
- Page 188 188
- Page 189 189
- Page 190 190
- Page 191 191
- Page 192 192
- Page 193 193
- Page 194 194
- Page 195 195
- Page 196 196
- Page 197 197
- Page 199 199
- Page 200 200
- Page 201 201
- Page 202 202
- Mapping CoS Values to Queues 203
- Mapping DSCP Values to Queues 204
- Configuring QoS Bandwidth 205
- Page 206 206
- Chapter 16.System Utilities 207
- Page 208 208
- Page 209 209
- Page 210 210
- Page 211 211
- Page 212 212
- System Utilities 213
- Viewing Optical Transceivers 214
- Chapter 17.Viewing Statistics 217
- Page 218 218
- Viewing Etherlike Statistics 219
- Managing RMON Statistics 220
- Page 221 221
- Page 222 222
- Configuring RMON History 223
- Viewing Statistics 225
- Page 226 226
- Configuring RMON Events 227
- Viewing the RMON Events Logs 228
- Page 229 229
- Defining RMON Alarms 230
- Page 231 231
- Chapter 18.Managing Stacking 233
- Stacking Chain Topology 234
- Stacking Members and Unit ID 234
- Exchanging Stacking Members 235
- Page 236 236
- Connecting a Terminal 237
- Initial Configuration 238
- Downloading Software 239
- Page 240 240
- Page 241 241
- Page 242 242
- Page 243 243
- Appendix B. System Defaults 244
- RS-232 Port Settings 245
- Port Defaults 245
- Configuration Defaults 246
- Security Defaults 246
- Jumbo Frame Defaults 246
- System Time Defaults 246
- Spanning Tree Defaults 247
- Address Table Defaults 247
- VLAN Defaults 247
- Trunking Defaults 248
- Multicast Defaults 248
- QoS Defaults 248
- Page 249 249
- Page 251 251
- Page 253 253
Verwandte Produkte und Handbücher für Software Allied Telesis AT-S94
Software Allied Telesis AT-S80 Betriebsanweisung
(242 Seiten)
(242 Seiten)
Software Allied Telesis AT-8000S Betriebsanweisung
(204 Seiten)
(204 Seiten)
Software Allied Telesis AT-S82 Betriebsanweisung
(76 Seiten)
(76 Seiten)
(49 Seiten)
(20 Seiten)LG MC-8047ARS manuels
Manuels d'utilisation et guides de l'utilisateur pour Non LG MC-8047ARS.
Nous fournissons des manuels en pdf 1 LG MC-8047ARS à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern