Allied Telesis AT-MC601 Bedienungsanleitung

Extended EthernetAT-MC601 AT-MC602 Installationand User’s Guide®PN 613-50647-00 Rev B

AT-MC601, AT-MC602 Installation and User’s Guide 10OverviewThese devices can be used in multi-dwelling units (MDU), multi-tenant buildings (MTU), and

Product Description11Location of ComponentsFigure 2 illustrates the front panels of the AT-MC601 and AT-MC602 network extenders.Figure 2 Front Panels

AT-MC601, AT-MC602 Installation and User’s Guide 12Hardware FeaturesThe following sections describe these hardware features of the AT-MC601 and AT-MC6

Product Description13PSTN Port The PSTN port allows you to connect the AT-MC601 Subscriber unit to a telephone and the AT-MC602 Provider unit to the o

AT-MC601, AT-MC602 Installation and User’s Guide 14Auto-Negotiation.The network extenders Auto-Negotiate the speed and duplex mode of the Ethernet lin

Product Description15Status LEDs The AT-MC601 and AT-MC602 network extenders feature the status LEDs defined in Table 4.MGMT Port The management port

AT-MC601, AT-MC602 Installation and User’s Guide 16Table 5 lists the management cable connector pins and their signals.DC PowerSupply InputPortThe net

Product Description17Software FeaturesThe AT-S57 software used to configure the AT-MC601 and AT-MC602 network extenders has the following features:❑ D

18Chapter 2InstallationThis chapter contains the installation procedures for the network extenders. The installation process is described in the follo

Installation19Installation Safety PrecautionsPlease review the following safety precautions before you begin to install the network extenders. Refer t

Copyright  2004 Allied Telesis K.K. www.alliedtelesyn.comAll rights reserved. No part of this publication may be reproduced without prior written per

AT-MC601, AT-MC602 Installation and User’s Guide 20AdditionalComplianceWarningStatementsAdditional telecommunication-related compliance warning statem

Installation21Selecting a Site for the Network ExtenderObserve the following requirements when choosing a site for your network extender:❑ If you plan

AT-MC601, AT-MC602 Installation and User’s Guide 22Cables Not IncludedThe AT-MC601 and AT-MC602 network extenders require the three cables described i

Installation23Unpacking the Network ExtenderTo unpack the network extender:1. Remove all components from the shipping package and store the packaging

AT-MC601, AT-MC602 Installation and User’s Guide 24Installing the AT-MC601 Subscriber UnitThe AT-MC601 Subscriber unit will most likely be used as a s

Installation253. Install the screws and plastic anchors onto the wall, as shown in Figure 7.Figure 7 Installing the Screws and Plastic Anchors Onto T

AT-MC601, AT-MC602 Installation and User’s Guide 26Cabling theSubscriber UnitTo cable the Subscriber unit, perform the following steps:1. First, conne

Installation273. Next, connect a telephone line cable from the VDSL Line port to the wall/interior telephone line, as shown in Figure 11, so that the

AT-MC601, AT-MC602 Installation and User’s Guide 28Installing the AT-MC602 Provider UnitThe AT-MC602 Provider unit can be installed in an AT-MCR12 rac

Installation29Wall-Mountingthe ProviderUnitThe Provider unit can be mounted onto a wall using the keyholes on the bottom of the unit. The screws and p

3Electrical Safety and Emission StatementStandards: This product meets the following standards.Warning: In a domestic environment this product may cau

AT-MC601, AT-MC602 Installation and User’s Guide 30Grounding theProvider UnitWhen an AT-MC602 Provider unit is used as a standalone network extender,

Installation31Rack-Mountingthe ProviderUnitTo install the Provider unit in an AT-MCR12 rackmount chassis, perform the following steps:1. Attach the un

AT-MC601, AT-MC602 Installation and User’s Guide 32Cabling theProvider UnitTo cable the Provider unit, perform the following steps:1. First, connect t

Installation333. Next, connect a telephone line cable from the VDSL Line port to the wall/interior telephone line, as shown in Figure 22, so that the

AT-MC601, AT-MC602 Installation and User’s Guide 34Warranty RegistrationWhen you have finished installing the network extender, register your product

35Chapter 3ConfigurationThe configuration software allows you to adjust and monitor the operating parameters of the media converter. Some of the funct

AT-MC601, AT-MC602 Installation and User’s Guide 36Starting a Configuration SessionDownloadingSoftware UpdatesIn order to configure and manage your AT

Configuration37Opening theConfigurationSoftwareOpen the configuration software by double-clicking the “ATS57” application icon, as you would with any

AT-MC601, AT-MC602 Installation and User’s Guide 38Configuring the Provider UnitAfter performing the procedure described in the previous section, ”Sta

Configuration39The parameters on the Configuration screen are described below.Upstream/DownstreamThe upstream and downstream data transfer rate.❑ Actu

4ContentsElectrical Safety and Emission Statement 3Preface ...

AT-MC601, AT-MC602 Installation and User’s Guide 40The Configuration Saved pop-up shown in Figure 27 will appear when the set rate or the highest poss

Configuration41VDSL Status To view the VDSL Status screen, click on the VDSL Status tab at the top of the menu.The VDSL Status screen is displayed in

AT-MC601, AT-MC602 Installation and User’s Guide 42Reduced Constellation LinkA lesser QAM constellation, causing reduced line rates. If the full const

Configuration43Ethernet Status To view the Ethernet Status screen, click on the Ethernet Status tab at the top of the menu.The Ethernet Status screen

AT-MC601, AT-MC602 Installation and User’s Guide 44Stop/StartThis button allows you to pause counting. When you press Stop, the counters remain at the

Configuration45Configuring the Subscriber UnitIn rare instances, you may need to use the configuration software on the Subscriber unit to attempt link

AT-MC601, AT-MC602 Installation and User’s Guide 46time, a timeout will occur. After a timeout, the default configuration parameters will be used to e

47Chapter 4TroubleshootingThis chapter contains information on how to troubleshoot the AT-MC601 and AT-MC602 network extenders in the event a problem

AT-MC601, AT-MC602 Installation and User’s Guide 48Verify that the ACT LED for each twisted pair port is ON. If a ACT LED is OFF, do the following:❑ V

Troubleshooting49If you are unable to establish a configuration session with the network extender and receive this error message, check to be sure tha

Contents5Cabling the Subscriber Unit...

AT-MC601, AT-MC602 Installation and User’s Guide 50❑ “Configuration file was not found” ❑ “Syntax error in configuration file”❑ “Configuration cannot

51Appendix ADefault Configuration SettingsThis appendix lists the AT-MC601 and AT-MC602 default settings. Setting DefaultProvider Parameters Monitore

52Appendix BTechnical SpecificationsPhysical SpecificationsDimensions: (W x D x H)109 mm x 95 mm x 25 mm(4.29 in. x 3.74 in. x 0.98 in.)Weight: .27 k

Technical Specifications53Safety and Electromagnetic Compatibility CertificationsEmission: EN55022 ClassA, FCC Part15 ClassAImmunity: EN55024Safety: E

54Appendix CTranslated Electrical Safety and Emission InformationImportant: This appendix contains multiple-language translations for the safety state

Translated Electrical Safety and Emission Information55Standards: This product meets the following safety standards. 1 RFI Emission EN55022 Class A,

AT-MC601, AT-MC602 Installation and User’s Guide 56Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. 1 Hochfrequenzstörung E

Translated Electrical Safety and Emission Information57Standarder: Dette produkt tilfredsstiller de følgende standarder. 1 Radiofrekvens forstyrrelse

AT-MC601, AT-MC602 Installation and User’s Guide 58Eisen: Dit product voldoet aan de volgende eisen. 1 RFI Emissie EN55022 Klasse A, FCC Part 15 Klas

Translated Electrical Safety and Emission Information59Normes: ce produit est conforme aux normes de suivantes. 1 Eemission d’interférences EN55022

6PrefaceThis guide contains instructions on how to install and configure the AT-MC601 and AT-MC602 Extended Ethernet units.How This Guide is Organized

AT-MC601, AT-MC602 Installation and User’s Guide 60Standardit: Tämä tuote on seuraavien standardien mukainen. 1 Radioaaltojen häirintä EN55022 Class

Translated Electrical Safety and Emission Information61Standard: Questo prodotto è conforme ai seguenti standard. 1 Emissione RFI (interferenza di E

AT-MC601, AT-MC602 Installation and User’s Guide 62Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. 1 RFI stråling EN550

Translated Electrical Safety and Emission Information63Padrões: Este produto atende aos seguintes padrões. 1 Emissão de interferência de EN55022 Cla

AT-MC601, AT-MC602 Installation and User’s Guide 64Estándares: Este producto cumple con los siguientes estándares. 1 Emisión RFI EN55022 Clase A, FCC

Translated Electrical Safety and Emission Information65Standarder: Denna produkt uppfyller följande standarder. 1 Radiostörning EN55022 Klass A, FCC

Preface7Document ConventionsThis document uses the following conventions:NoteNotes provide additional information.WarningWarnings inform you that perf

AT-MC601, AT-MC602 Installation and User’s Guide 8Contacting Allied Telesyn Technical SupportThis section provides Allied Telesyn contact information

9Chapter 1Product DescriptionThe AT-MC601, AT-MC602 Extended Ethernet products are designed to transmit data at very high speeds over unshielded pairs